Merrithew Health & Fitness Tower Trainer User manual

OWNER’S MANUAL
Please review this important assembly, safety and warranty information
about your new MERRITHEW™Tower Trainer and keep it handy for future reference.

Tower Trainer™Owner’s Manual
17.
2
26.
24.
.
29.
28.
30.
32.
31.
21.
22.
23.
19.
16.
18.
20.
1 Eyehook
2 Upper Tube Assembly
3 Safety Chain
4 Spring Clip
5 Large Securing Knob
6 Light Arm Springs (Yellow)
7 Left Sliding Stability Bar Holder
8 Roll-Down Bar
9 Foam Grip Handles
10 Left Upright
11 Wheel Cap
12 Outer Cover
13 Base Frame
14 Main Frame
15 Handle Strap
16 Round Feet
17 Serial Number Sticker (see pg. 5 for detail)
18 Extension Frame
19 Raised Extension Mat
20 Raised Main Mat
21 Locking Knob
22 Raised Base Mat
23 Inner Cover
24 Right Upright
25 Push-Thru Bar
26 Push-Pin
27 Fuzzy Hanging Straps [fig. A]
28 Right Sliding Stability Bar Holder
29 Spring-loaded Pin
30 Sliding Stability Bar
31 Padded Sliding Stability Bar Sleeve
32 Rolldown Spring (Black)
33 Single D-ring Strap [fig. B]
34 Leg Springs (White) [fig. C]
35 Padded Long Spine Straps [fig. C]
36 Push-Thru Spring (Blue)
37 Vinyl Spring Cover [fig. D]
38 Locking Spring Clip [fig. D]
39 Bolt-on Wheels [fig. E]
Part Identification for the Tower Trainer™
Hardware Identification
QTY
40 Screw, Round Head (M4 x 20mm) 4
41 Bolt, Button Head (M8 x 1.25 x 50mm) 2
42 Bolt, Button Head (M8 x 1.25 x 55mm) 2
43 Bolt, Button Head (M8 x 1.25 x 60mm) 4
44 Bolt, Button Head (M8 x 1.25 x 76mm) 8
45 Acorn Nut (M8 x 1.25) 4
46 Nylock Nut (M8 x 1.25) 12
47 Washer (M8) 8
48 Arc Washer (M8) 16
49 Lock Washer (M8) 4
Covered by one or more of the following patents and/or patent applications:
US 8,057,371 B2, 7,878,954 B2, US Application No. 11/329,252, US Application No. 12/233,968,
US Application No. 60/642,985, PCT International Application No. 2006000814.
17

merrithew.com
C
A
34
33
27
35
3
11
6.
5.
7.
10
1.2.3.
13
8.
4.
9.
12
15
14
REQUIRED TOOLS:
1/4" (6MM) HEX KEY
COMBINATION WRENCH
D
E
36
37
39
38
38

Tower Trainer™Owner’s Manual
4
User Guidelines
The Tower Trainer is a multifunctional piece of equipment that
canbe used for Pilates, dance and traditional fitness training.
It is a portable unit that can be folded for storage, then laid
outflatwhen in use.
The Trainer comes equipped with a full compliment of springs,straps
and a safety chain. The springs can be attached tovarious locations
on the frame, or on the straps hooked aroundthe sliding bar.
Besure your spring clips are completely closed and secure.
For inexperienced or first-time users, the Tower Trainer
should only be used under the supervision of a
trained professional.
This manual includes general guidelines for setup and usage. To get
the most out of your Tower Trainer, MERRITHEW offers instructional
DVDs and manuals. Personalized training is offeredthrough our
Licensed and Corporate Training Centers.
Visit merrithew.com for more information.
For questions or technical assistance,
email [e-mail]
Care & Cleaning
Wipe vinyl surfaces with a mixture of water and tea tree oil,
a natural disinfectant.
Add 5ml or 1tsp of tea tree oil to a 1L or 1qt spray bottle ofwater.
A mixture of mild soap and water may be used to remove more
persistent dirt. Ensure cleaner does not leave an oily residue,
or make surfaces slippery.
Clean all metal surface areas as required, using a soft cloth
and gentle cleaner.
IMPORTANT!
This manual contains important assembly, safety and warranty
information. Read the manual carefully before using your new
TowerTrainer™and keep the manual on hand for future reference.
UNSAFE OR IMPROPER USE OF THIS EQUIPMENT BY
FAILING TO READ AND COMPLYWITH ALL REQUIREMENTS
ANDWARNINGS COULD RESULT IN SERIOUSINJURY.
It is impossible to predict every situation and condition that can
occur while using your Tower Trainer. MERRITHEW™makes no
representation about the safe use of the Tower Trainer under all
conditions. There are risks associated with the use of any exercise
equipment that cannot be predicted or avoided, and you assume
the responsibility for that risk.
Please ensure that you and your clients/patients have received
proper instruction regarding the correct and safe use of
MERRITHEW equipment. We recommend cautious assembly and
usage and wish you many hours of safe and effective exercise.
Safety Instructions
WARNING: As with any athletic activity, the use of exercise
equipment involves risk of injury, damage and/or death.
By choosing to use MERRITHEW equipment, you and/or your clients/
patients assume responsibility for that risk, not the people who sold
you the equipment, distribute and/or manufacture it.
wWe recommend that two people be available for assembly
of this product.
wSet up and operate the Tower Trainer on a solid level surface.
Do not position the Tower Trainer on loose rugs or
uneven surfaces.
wMake sure that adequate space is available for access to
and around the Tower Trainer.
wEnsure that the Main Frame is secured properly on the Base Frame
with the locking knobs before using the Tower Trainer.
wAlways make sure that the Dowel Holder is adjusted to the
same height with Spring Pins in parallel holes in Uprights.
wAlways choose the workout which best fits your physical strength
and flexibility level. Know your limits and train
within them. Always use common sense when exercising.
wDo not wear loose clothing while using the Tower Trainer.
wBe careful to maintain your balance while using, mounting,
dismounting or assembling the Tower Trainer, loss of balance
may result in a fall and serious injury.
wThe Tower Trainer should not be used by persons weighing
over 250 lbs (113 kgs).
wThe Tower Trainer should be used by only one person at a time.
Mechanical
Safety Check
Proper maintenance and timely replacement of your equipment or
component parts is your responsibility as it helps reduce the risk of
injury. Conduct a regular inspection of the following:
DAILY
wClean all surface areas after each use, using a soft cloth
and gentle cleanser.
WEEKLY
wCheck all springs and spring clips for wear and damage
and replace as needed.
MONTHLY
wEnsure all nuts, bolts and screws are securely fastened.
wEnsure eyehooks are securely fastened.
YEARLY
wReplace all spring clips.
EVERY TWO YEARS
wReplace all springs.
REPLACE ALL SPRINGS EVERY 24 MONTHS AND SPRING CLIPS
EVERY 12 MONTHS OR AS NEEDED WITHIN THAT PERIOD.
FAILURE TO PERFORM RECOMMENDED SAFETY CHECKS, OR
USING THE MACHINE WITH IMPROPERLY ADJUSTED, BROKEN OR
WORN PARTS, COULD RESULT IN SERIOUS BODILY INJURY.

merrithew.com
48
28
29
46
5
IMPORTANT! PLEASE DO NOT ATTEMPT TO ASSEMBLE
ON YOUR OWN. THIS IS, AT MINIMUM, A JOB FOR TWO
PEOPLE. PLEASE READ THESE INSTRUCTIONS COMPLETELY
BEFORE BEGINNING ASSEMBLY.
Place all parts from the box in a cleared area and position them on
the floor in front of you. Remove all packing material from your area
and place them back into the box. Do not dispose of the packing
materials until assembly is completed. To prevent unsafe or improper
use, please read each step carefully before beginning.
For assistance or to report missing parts:
Call: Toll-free in North America 1-800-910-0001
Toll-free in United Kingdom 0800-328-5676 or
Email [e-mail]
Please refer to the assembly instructions included
in this Owner’s Manual for initial Assembly Instructions
and Part Identification.
Assembly Instructions
1Attach the bolt-on wheels [39] to the base frame [13] by
inserting the button head bolts [44] and arc washer [48],
secure with arc washer [48] and nylock nut [46].
2Attach the left [10] and the right uprights [24] to the base frame
[13] by inserting the button head bolts [44] and arc washers [48]
from top and secure with arc washers [48] and nylock nut [46] from
bottom. Do not tighten the bolts until step 6.
NOTE: The correct positions of the holes and eyehooks on
the left upright and right upright in the illustration. The holes
face away from the raised base mat [22] and the eyehooks
face to the outside.
3Pull the spring-loaded pin [29] then slide the right sliding
stability bar holder [28] onto the right upright [24]. Release the
spring-loaded pin so it catches in one of the adjustment holes and
locks the holder in place. Repeat with the left sliding stability bar
holder [7] and left upright [10]. Position the left and right sliding
stability bar holders so they are the same distance from the top of
the left and right uprights.
NOTE: The correct position of the eyehooks on the sliding stability
bar holders in the illustration. The eyehooks face to the outside.
7
10
24
48
44
39
44
13
22
Serial Number
Placement
48
STEP 1
STEP 3
STEP 2
17

Tower Trainer™Owner’s Manual
Tower Trainer
™
Owner’s Manual
28.
24.
44.
30.
49.
45.
40.
23
STEP 6
6
Assembly Instructions CONT’D
4 Attach the sliding stability bar [30] to the left and right
sliding stability bar holders [7, 28] with button head bolts [43],
lock washers [49] and acorn nuts [45]. Do not tighten
the bolts until Step 6.
NOTE: The padded stability sleeve can easily be removed
by undoing the zipper.
5Insert the upper tube assembly [2] into the left and right uprights
[10, 24] and secure with the large securing knobs [5].
NOTE: The correct position of the holes and eyehooks [1]
on the upper tube assembly [2] in the illustration below.
6Tighten the button head bolts [43] to secure the sliding stability
bar [30]. Tighten the button head bolts [44] to secure the left and
right upright [10, 24].
7Attach the outer cover [12] and inner cover [23] to the right
upright [24] with round head screws [40]. Repeat on other side.
2.
1.
43.
5.
7.
10
12
STEP 5
STEP 4
STEP 7

merrithew.com 7
STEP 9
STEP 8 18
42
47
46
21
14
13
47
46
41
8Place the main frame [14] with the mat side face down.
Attach the extension frame [18] by placing it (mat side up)
on top of the mat frame, aligning hinge brackets.
Use button head bolts [42], washers [47] and nylock
nuts [46] to secure together.
9 Unfold the extension frame [18] from the main frame [14]
and turn the mat side face up. Attach the Main frame [14] to the
base frame [13] with button head bolts [41], washers [47], and
nylock nuts [46]. Lock the main frame [14] and the base frame [13]
together with the locking knobs [21].

Tower Trainer™Owner’s Manual
10
26
8
Safety & Usage
SLIDING STABILITY BAR ADJUSTMENT
To adjust the height of the Sliding Stability Bar [30], pull out on the
spring-loaded pins [29] and carefully slide the bar to the desired
location. Release the pins and ensure they are fully locked in one
of the holes. The bar also comes with a soft padded covering to
increase comfort and usability.
NOTE: Always make sure that the sliding stability bar holders
[7, 28] are adjusted so the bar is parallel with the mat.
SET-UP FOR THE PUSH-THRU BAR
Attach the push-thru bar [25] to the top adjustment hole
in the uprights [10, 24] with two upper push-pins [26].
Attach the safety chain [3] to the eyehook [1] on the top of the
upper tube assembly [2]. For some exercises, the push-thru bar [25]
should be up and secured in position with the safety chain [3].
The push-thru bar [25] can be used as a foot bar for some exercises.
Attach the push-thru bar (25) to the lowest adjustment hole in the
upright [10, 24] with two upper push-pins [26].
Lock the push-thru bar [25] to the uprights [10, 24] with
two lower push-pins [26].
NOTE:
wThere are three adjustment holes in the uprights that allow you to
attach the push-thru bar [25] at one of the different heights.
wRefer to the inset illustration. Push down the button on the “T”
end of the push-pins [26] to release. Then you can insert
the push-pin [26] into the adjustment hole.
wAlways make sure the safety chain [3] is connected when the
push-thru bar [25] is in use in the rotating positions.
1.
2.
3.
29.
28.
25.
24.
30.7.

merrithew.com
2.
3.
25.
24.
4.
37.
36.
1.
4.
36.
38.
25.
9
USING THE PUSH-THRU BAR
SPRINGS FROM ABOVE
When doing exercises that require the spring resistance to come
from above the bar, attach the push-thru spring [36] to the eyehook
on the upper side of the push-thru bar [25] with the locking spring
clip [38]. Attach the other end of the push-thru spring [36] to one of
the eyehooks [1] on the upper tube
assembly [2] with the spring clip [4].
CAUTION: To prevent accidental injury, never put your face
(or another body part) above the push-thru or roll-down bars
while spotting an exercise.
SPRINGS FROM BELOW
CAUTION! If using the push-thru bar with springs from below,
attach safety chain first.
1. When using the push-thru bar [25] with the push-thru spring [36]
attached from below for bottom load exercises, connect one end
of the safety chain [3] to one of the eyehooks [1] on the upper
tube assembly [2] with the spring clip [4]. Connect the other end
of the chain to the eyehook on the push-thru bar [25] with the
spring clip [4] as per illustration below.
2. Hook the spring to the eyehooks located at the base on the other
side of the upright [10 or 24] with the spring clip [4];
see illustration below. Ensure that the vinyl spring cover [37]
which covers the push-thru spring [36] is moved over the lower
part of the spring to avoid catching the user’s hair or clothing,
and to keep the spring from coming into contact with the
upholstered raised mat.
3. Attach the push-thru spring [36] to the loop on the underside
of the push-thru bar [25] with the locking spring clip [38],
as per illustration below.
Be sure that the safety chain is always connected to the push-thru
bar when in use with springs from below.
38.
10.
4.

Tower Trainer™Owner’s Manual
9.
35.34.
6.
38
10
ROLL-DOWN BAR
The roll-down bar [8] attaches via the rolldown springs [6]
to the eyehooks [1] on the upper tube assembly [2] between the
twouprights [10, 24] with the spring clip [4]. Attach the arm springs
[6] to the roll-down bar [8] with the spring clip [4].
Ensure the spring clips are completely closed and secure.
LIGHT ARM SPRINGS (YELLOW)
Attach light arm springs [6] to eyehooks at desired height
with the locking spring clip [38]. Attach the other ends of the
springs to the foam grip handles [9] with the spring clips [4]. Ensure
the spring clips are completely closed and secured.
LEG SPRINGS (WHITE)
Attach leg springs [34] to eyehooks at desired height with the
locking spring clips [38]. Attach the other ends of the springsto the
padded long-spine straps [35]. Ensure the clips are completely closed
and secured.
1.
4.
6.
10.
4
8.
2.
24.
Safety & Usage CONT’D

merrithew.com
To order, visit merrithew.com/replacementparts or email [e-mail]
25.
14/20.
24.
26.
13.
2.
16/18
15.
21
11
WARNING: When folding or unfolding the Tower Trainer™,
keep all children away from the Tower Trainer and make
sure hands and feet are clear of any folding or pinch point.
FOLDING
a. Move any attached accessories to the back side of the tower so
the mats can fold up against the sliding stability bar [30].
b. Ensure upper and lower push-pins (26) are inserted with the
push thru bar (25) locked down.
c. Remove the locking knobs [21] to unlock the main frame [14].
d. With one hand on one of the handle straps [15] on the raised
main mat [20], and one hand on the extension frame [18],
slowly lift the main frame [14] and extension frame [18].
The extension frame [18] will fold down against the
main frame [14] as you lift.
e. When both frames are in the most vertical position possible,
parallel to the left and right uprights [10, 24], secure the
main frame [14] to the left and right uprights [10, 24] with the
locking knobs [21].
UNFOLDING
a. Unscrew the locking knobs [21] from
the uprights completely.
b. With one hand on the handle strap [15] of
the raised main mat [20], and one hand on the
extension frame [18], carefully extend it completely
to rest on the floor.
c. Replace the locking knobs [21] securing the
main frame [14] to the base frame [13] and
fully tighten for security.
MOVING
To move the Tower Trainer, it must be folded. The push-thru bar
must be locked down. While on the wheeled side of the folded
Tower Trainer, grasp the upper tube assembly [2] with one hand,
place your foot against the base frame [13], and hold the upright
with your other hand. Pull the Tower Trainer toward you while
holding the base steady with your foot until the wheels come in
contact with the floor. Then roll the Tower Trainer while holding the
upper tube assembly [2] and right upright [24] to steady and guide
the Tower Trainer.
STORING
Store the Tower Trainer in a clean, dry place.
Storage & Mobility

Tower Trainer™Owner’s Manual
Replacement Parts
REPLACEMENT SPRING
PACKAGE
Springs should be replaced every 24 months,
or as needed within that period.
A complete spring replacement package is
available for the Tower Trainer and includes:
w2 roll-down springs
w2 leg springs
w2 arm springs
w2 push-thru springs
w10 spring clips
(carabiners)
w63 locking
spring clips
ROLL-DOWN DOWN BAR WITH
SPRINGS (BLACK) & CLIPS
FOAM GRIP HANDLES
Cushioned and rounded, these provide
extracomfort.
PUSH-THRU SPRINGS (BLUE)
For use with push-thru bar.
SINGLE D-RING STRAP
Connecter for attaching springs
to stability bar.
PADDED SLIDING
STABILITYBAR SLEEVE
Removable covering adds cushioning to
sliding stability bar.
PADDED LONG SPINE STRAPS
Also available without padding.
LEG SPRINGS (WHITE)
Shown with padded long spine straps
attached. (sold separately)
ARM SPRINGS (YELLOW)
Shown with foam grip handles attached.
(sold separately)
FUZZY HANGING STRAPS
Soft and woolly, these add extra comfort
and security for specific exercises.
LARGE SECURING KNOB
Use to secure upper tube assembly
to uprights.
LOCKING KNOB
Use to lock in folded or unfolded position.
12

merrithew.com
Optional Items
FOAM CUSHIONS
Available in three sizes. Used for comfort
and additional support when performing
a wide variety ofexercises.
GRIPPER MATS
Non-slip rubber mats are handy to
increase traction and prevent slipping.
A gripper mat can be wrapped around
push-thru bar, roll-down bar, uprights
or placed on upholstered bed.
TPE PILATES PAD
Non-slip eco-friendly pads can help establish
correctalignment and positioning or to
provide cushionedsupport.
PADDED PLATFORM
EXTENDER
Can be used on the upholstered bed
REFORMER BOX
Used to facilitate or vary exercises.
ARC BARREL
Ideal to increase or decrease challenge
and to assist rehab clients.
MAPLE & METAL
ROLL-UP POLE
Provides added scapular awareness.
Sold separately.
EXTENSION STRAPS
SAFETY CHAIN
For use with push-thru bar.
NON-LOCKING SPRING CLIP
& LOCKING SPRING CLIP
Locking spring clips are required when using
push-thru bar with springs from below.
PUSH-PIN
Used to secure push-thru bar.
To order, visit merrithew.com/replacementparts or email [e-mail] 13

Tower Trainer™Owner’s Manual
14
CAUTION
IMPROPER USE OF EXERCISE EQUIPMENT MAY
CAUSE SERIOUSBODILY INJURY. TO REDUCE RISK,
PLEASE READ THE FOLLOWING:
wBefore starting any exercise program, consult a physician.
wBefore using the equipment, read and follow Safety
instructions in this Manual and obtain thorough instruction
from a qualified trainer.
wThe Tower Trainer™must be used under the supervision
of a trained professional.
wUse equipment only for intended exercises.
wEnsure the equipment is properly adjusted for your size
and ability level.
wWhen springs are used, ensure spring clips are fully closed
at both ends of springs. A spring clip that is only half closed
risks coming undone and detaching with high force.
wWhen using the push-thru bar with spring from below,
locking spring clips must be used to attach to the frame or
uprights, and the safety chain must be attached.
wWhen using the push-thru bar, a trained professional must
keep a hand on the bar at all times.
wStop exercising if you experience chest pain, feel faint, have
difficulty breathing or experience musculoskeletal discomfort.
wKeep body, clothing and hair free from all moving parts.
wDo not use if equipment appears worn, broken or damaged.
wDo not attempt to repair equipment yourself without
consultingMERRITHEW.
wDo not allow children to use or be around equipment
withoutadult supervision.
wAll springs must be replaced every 24 months or as needed
withinthat period.
wAll spring clips must be replaced every 12 months or
as needed within that period.
Warranty
MERRITHEW TOWER TRAINER
MERRITHEW™warrants that this equipment is free of manufacturing
defects in workmanship and materials, subject to the terms below.
Thiswarranty becomes effective at the invoice date of the original
purchase. Parts repaired or replaced under the terms of this warranty
willbe warranted for the remainder of the original warranty period.
This warranty applies to equipment only:
wwhile it remains in the possession of the original purchaser and
proof of purchase is demonstrated
wif claims are made within the warranty period
wif upgrades are made as required by MERRITHEW
THIS WARRANTY SHALL BE NULL AND VOID if:
wthe equipment is for any other purpose other than as intended
wall safety and usage guidelines arenot followed as specified
wequipment failure is a result of improper maintenance
wequipment has been subjected to accident, misuse, abuse,
improper service, or any modification not authorized by
MERRITHEW
This warranty does not cover damage to the finish of any MERRITHEW
equipment, or shipping charges, customs clearance fees (if applicable)
orany costs incurred in installing repaired or replacement parts
shippedunder the provisions of this warranty.
FIVE (5) YEAR LIMITED WARRANTY
MERRITHEW will, at its option, repair or replace any of the parts
listedbelow, provided that the part(s) fail due to a defect
in workmanship or materials:
wvertical bars and overhead frame
wcomponents of the frame and related welding
TWO (2) YEAR LIMITED WARRANTY
MERRITHEW will replace springs that fail for any reason, provided
suchfailure is reported to MERRITHEW within a period of two years
fromthe invoice date of the original purchase. We recommend that
springs be changed every two (2) years.
ONE (1) YEAR LIMITED WARRANTY
On other parts and components. We recommend that spring clips
be changed annually.
90-DAY FABRIC WARRANTY
The vinyl fabric upholstery will be replaced if it fails to give normal
wear for 90 days after delivery. Proof of damage may be required.
Thiswarranty does not cover cuts, burns, stains, soiling, pet damage
ordamage caused by other unreasonable use. This warranty does not
apply to fabrics cleaned with abrasive, corrosive or chemical cleansers.
Ifthe identical fabric is not available, MERRITHEW will provide an
equivalent fabric.
DISCLAIMER OF IMPLIED WARRANTIES
AND LIMITATION OF REMEDIES
Repair or replacement of defective parts is your exclusive remedy under
the terms of this limited warranty. In the event of parts availability issues,
MERRITHEW will not be responsible for any consequential or incidental
damages arising from the breach of either this limited warranty or any
applicable implied warranty, or for failure or damage resulting from
acts of nature, improper care and maintenance, accident, alteration,
replacement of parts by anyone other than MERRITHEW, misuse,
transportation, abuse, hostile environments (inclement weather, acts of
nature), improper installation or installation not in accordance with local
codes orprintedinstructions.
This limited warranty is the sole express warranty given by
MERRITHEW. No product performance, specification or description
wherever appearing is warranted by MERRITHEW except to the
extent set forth in this limited warranty. Any implied warranty
protection arising under the laws of any state, provinceor
territory including implied warranty of merchantability or fitness
for a particular purpose, oruse, is hereby limited in duration
tothe duration of this limited warranty.
Neither distributors, dealers, web resellers, nor the retailers selling
this product have any authority to make any additional warranties or
to promise remedies in addition to or inconsistent with those stated
above. MERRITHEW maximum liability, in any event, shall not exceed the
purchase price of the product paid by the original purchaser.

Expand Your Repertoire
Increase your expertise with DVD Instruction
This DVD focuses on the biomechanical principles of STOTT PILATES®while using the
variouscomponents of the Tower Trainer™to develop core stability and improve flexibility.
Enjoythis hybrid workout of Pilates and traditional fitness moves that increase overall
strengthandconditioning.
We offer almost limitless exercise challenges in our clear and detailed repertoire of instructional
DVDs. For a full listing visit merrithew.com/shop/dvds
size: 27"x 39"
Take advantage of our training tools
Tower Trainer™Wall Chart: This full-size wall chart depicts exercises featured in the
STOTTPILATES®Programming on the Tower Trainer™and CORE Athletic Conditioning &
Performance Training on the Tower Trainer™programs. Each exercise is described with
name,equipment accessories, one photo, as well as suggested repetitions.
Our Wall Charts are printed with vegetable-based inks on FSC paper.
A step-by-step exercise guide for the Tower Trainer repertoire can
be downloaded by visiting merrithew.com/guide
Mindful Movement education that
gives you the competitive edge.
For over 25 years, we have been committed to developing effective and responsible exercise
through unique, high‑integrity fitness programs. Our signature STOTT PILATES®education method
isunparalleled in the industry. OurZEN•GA®, CORE™Athletic Conditioning & Performance Training™
and Total Barre™programs offer additional repertoire to challenge your workouts. We invite you
to join our worldwide community of elite fitness professionals—with TheProfessional’s Choice™
inPilatesand Mindful Movement Education. Coursesand workshops are offered worldwide.
Explore merrithew.com/education/training for courses andworkshops near you.
Contact Us Today:
call toll-free North America 1.800.910.0001 United Kingdom 0800.328.5676 or International +1-416.482.4050 merrithew.com

Please keep this manual in a safe place.
IMPORTANT
This is your Tower Trainer™Serial Number:
P00215 PM-ST02093A JAN16 ™/® Trademark or registered trademark of Merrithew Corporation, used under license. Printed in Canada. All rights reserved.
Go to
merrithew.com/warranty
to activate your warranty!
Get the benefits:
wEnsure that you’ll be able to repair it under warranty should you encounter a problem.
wMake warranty service fast and efficient by having your information in our records.
wIn the unlikely event of a replacement or safety notice, we’ll be able to contact you immediately.
wProof of purchase for insurance purposes in the event of a loss due to fire, flood or theft.
wStay informed of any product updates.
Can’t get online?
Please fill out the warranty card enclosed with this product, and return to us.
2200 Yonge Street, Suite 500, Toronto, ON M4S 2C6 phone [phone]
fax [phone] email [email protected] website merrithew.com