Messoa NCB855E User manual

www.messoa.com
Fixed Network Camera
NCB855E/NCB855PRO/NCB858
Quick Start Guide
Guia de inicio rápido
Guida rapida
Guide de démarrage rapide
Краткое руководство
クイックスタートガイド
快速安裝指南
快速安装指南
ZEIM-4000813G 2012-09 A1

NCB855E/NCB855PRO/NCB858 l Quick Start Guide 1
English
Safety Instructions
Make sure the supplied voltage meets the power consumption
requirements of the camera before powering the camera on.
Incorrect voltage may cause damage to the camera.
The camera should be protected from water and moisture,
excessive heat, direct sunlight and cold.
This installation should be made by a qualied service person and
should conform to all local codes.
Unplug the camera during lightning storms or when unused for
long periods of time.
Copyright
No part of this document may be reproduced or transmitted in any form
or by any means, electronic or mechanical, for any purpose, without
the express written permission of MESSOA.
© 2012 All rights reserved.
Disclaimer
Specications and information contained in this document are
presented as accurately as possible as of the time of release, but
are not guaranteed to be entirely free of error. MESSOA assumes no
responsibility for errors or omissions that may appear in this document
and reserves the right to change this publication at any time without
obligation to notify anyone of such revisions or changes.

2 NCB855E/NCB855PRO/NCB858 l Quick Start Guide
Compliance
This equipment complies with the requirements as listed below:
FCC Part 15 Class B
CE: 2004/108/EC-Electromagnetic Compatibility (EMC) directive of
EN55022, EN61000-3-2, EN61000-3-3 and EN50130-4.
WEEE
Waste Electrical and Electronic Equipment
Correct disposal of this product (applicable in the European
Union and other European countries with separate collection
systems). This product should be disposed of, at the end of
its useful life, as per applicable local lows, regulations and
procedures.

NCB855E/NCB855PRO/NCB858 l Quick Start Guide 3
English
1. Introduction
Package Contents
Fixed Network Camera x1
CD-ROM (User manual and IP Finder utility) x1
Quick Start Guide x1
2-pin Screw Terminal Block x1
6-pin Screw Terminal Block x1
CS-C Mount Adapter Ring x1
Hardware Overview
Part Names




1. Lens mounting ring: For mounting a CS-mount or C-mount lens.
2. Back Focus Control: Allows to adjust the distance between the
back ange of the lens mounting and the image sensor.
3. Auto Iris control: Supplies power and control signals to an auto-
iris lens.
4. Tripod screw hole: Use these screw holes to attach a tripod
mount. You can attach the mount to either the top or bottom side.
(screw: 1/4”).

4 NCB855E/NCB855PRO/NCB858 l Quick Start Guide
Rear Panel
Micro
SD
Card Audio Out Audio In
Reset
Power
Video
DC 12V
AC 24V
+
~~
Ethernet/PoE
1 2 3 4 5 6
RS485+
GND
ALM-In 1
ALM-In 2
RS485
ALM-Out







1. DC 12V/AC 24V: Connect the power terminals to a power supply.
If using DC 12V power supply, make sure to connect the power
connector to correct polarities (Red+/White–).
If you plan to use power via an Ethernet connection, this connector
is not used.
2. Video: To perform focus and iris adjustments during the
installation, connect the camera to a monitor.
3. Power LED: The LED lights on when power is applied.
4. Audio In: Connects to an external microphone
5. Reset: Using a pointed object, hold down the reset button no
more than 5 seconds to restart the camera. Or hold down the reset
button for longer than 5 seconds to reset the camera to the factory
defaults.
6. Audio Out: Connects to a speaker.
7. Memory Card Slot: Insert a microSD/SDHC card to the slot for
recording and storage.

NCB855E/NCB855PRO/NCB858 l Quick Start Guide 5
English
8. I/O: Connect your external devices, e.g., sensors and alarms to
the corresponding I/O terminal block. The pins of the I/O terminal
block controls the following signals:
Pin Signal Connection
1 RS485+ Reserved.
2 RS485- Reserved.
3 GND Ground (electricity) in electrical circuits.
4 ALM-Out Connect to device that responds to alarm
signals.
5 ALM-IN 1 Connect to device that triggers alarm signals.
6 ALM-IN 2 Connect to device that triggers alarm signals.
9. Ethernet/PoE: Connects to the LAN port of a standard
10BaseT/100BaseTX device, e.g., hub, switch or router.

6 NCB855E/NCB855PRO/NCB858 l Quick Start Guide
Dimensions
114mm (4.5”) 66mm (2.6”)
56mm(2.2”)
65mm(2.6”)
Micro
SD
Card Audio Out Audio In
Reset
Power
Video
DC 12V
AC 24V
+
~~
Ethernet/PoE
1 2 3 4 5 6
RS485+
GND
ALM-Out ALM-In 1 ALM-In 2
RS485
2. Installation
1. Installing the Lens
Attache your lens onto the camera’s lens mounting ring.
CS-Mount lens: Attach the lens to the camera directly.
C-Mount lens: You must mount the supplied CS-C mount adapter
ring rst and then attach the C-Mount lens.
If you are using an auto-iris lens, connect the auto-iris cable to the
IRIS control connector on the camera.

NCB855E/NCB855PRO/NCB858 l Quick Start Guide 7
English
2. Mounting the Camera
Mount the camera to your intended location. Be sure to rmly attach
the camera to a suitable at surface.
3. Connecting the Cables
1. Optionally connect external input/output devices to the camera.
2. Optionally connect a speaker and microphone to the camera.
3. Connect the camera to a power source, using one of these options:
• DC 12V or AC 24V: Connects to the power terminals on the
rear panel. If using DC 12V power supply, make sure to connect
to correct polarities (Red+/White–).
• PoE: Using a Cat. 5/5e or above UTP/STP cable, connect the
LAN port to an IEEE 802.3af compliant network device. Power
will be supplied through the Ethernet cable.
4. Optionally connect a video monitor if you want to perform focus
and iris adjustments during the installation.
4. Adjusting the View and Focus
Adjust the focus controller, and zoom controller of the lens to get the
best resolution. If needed, adjust the back focus to achieve the focus.

8 NCB855E/NCB855PRO/NCB858 l Quick Start Guide
5. Connecting to a PC for Initial Conguration
Before connecting the camera to your network infrastructure, it’s
suggested that you connect the camera to a computer rst to perform
initial congurations.
1. Configure the computer’s IP address that must be on the same
network segment with the camera’s default IP address, such as:
• IP Address: 192.168.1.100
• Subnet Mask: 255.255.255.0
2. Connect the camera via a Cat. 5/5e or above UTP/STP cable to the
computer.
The LAN port of the camera supports auto MDI/MDIX so there is no
need to use a cross-over cable.
3. On the PC, launch a web browser and enter the IP address of the
camera in the URL eld:
http://192.168.1.30
4. When prompted for login, enter the default user name: admin and
password: 1234 to log in. Note that the user name and password
are case-sensitive.
5. Configure the settings to meet your requirements. For more
information, refer to the User Manual on the provided CD.
6. Connecting to Your Network
Connecting to a LAN
If you have multiple cameras installed on your network, you can
use the provided IP Finder utility to manage the cameras. For more
information, refer to the User Manual on the provided CD.

NCB855E/NCB855PRO/NCB858 l Quick Start Guide 9
English
Router/Switch/Hub
Connecting to the Internet
Router
xDSL/Cable
Modem
To enable remote access to the cameras, you must configure your
router/rewall to open port numbers. For more information, refer to the
User Manual on the provided CD.

10 NCB855E/NCB855PRO/NCB858 l Quick Start Guide
3 Years Limited Warranty
MESSOA Technologies Inc. (MESSOA) warrants the party that made the
original purchase from MESSOA that the product is free from defects in
designs, materials and workmanship under normal use for a period of 3
(three) years from the date of the original purchase. For zoom Lens, IR
LED light bulbs, and IP Board of IP speed domes, the warranty period
shall be limited to a period of 1 (one) year from the date of the original
purchase. The actual term of warranty will be determined based upon
the product serial number.
Any claim to be made by the original purchase party during the
warranty period shall follow the terms and procedures stated in
MESSOA’s 3 Year Warranty Service Program Agreement. A valid bill
of sale must be presented to establish warranty eligibility. Repaired
product following the RMA maintenance procedure will be warranted for
the remainder of its original warranty period.
This Limited Warranty does not apply (i) to damages caused by
acts of nature, abuse, misuse, misapplication, improper interfacing,
improper repair, unauthorized modication, or any operation beyond
the design limits, (ii) to software-related conguration errors, software
compatibility and virus, (iii) to consumables and spare parts, including
but not limited to plastic housing and covers, accessories, and
packaging materials.
This Limited Warranty is applicable in all countries. Should the product
malfunction, please contact the party from whom you purchased the
product for assistance.

www.messoa.com
Cámara de Red Fija
NCB855E/NCB855PRO/NCB858
Quick Start Guide
Guia de inicio rápido
Guida rapida
Guide de démarrage rapide
Краткое руководство
クイックスタートガイド
快速安裝指南
快速安装指南
ZEIM-4000813G 2012-09 A1

NCB855E/NCB855PRO/NCB858 l Guía de inicio rápido 1
Español
Instrucciones de seguridad
Asegúrese de que el voltaje suministrado reúne los requisitos de
consumo energético de la cámara antes de encenderla. Un voltaje
incorrecto podría dañar la cámara.
La cámara debe estar protegida del agua y la humedad, calor
excesivo, frío y luz directa del sol.
La instalación debe ser realizada por personal cualicado de
mantenimiento siguiendo todas las normativas locales.
Desconecta la cámara durante tormentas eléctricas o cuando no
vaya a ser utilizada durante largos periodos de tiempo.
Copyright
Ninguna parte de este documento podrá ser reproducida ni transmitida
de ninguna forma o medio, electrónico mecánico, para ningún
propósito, sin el permiso expreso por escrito de MESSOA.
© 2012 Todos los derechos reservados.
Exención de responsabilidad
Las especicaciones y la información contenidas en este documento se
presentan con la mayor precisión posible cuando fue publicado, pero
no se garantiza que no haya algún error. MESSOA no asume ninguna
responsabilidad por los errores o emisiones que pudieran aparecer
en este documento y se reserva el derecho de modicar el presente
en cualquier momento sin la obligación de noticar a nadie dichas
revisiones o modicaciones.

2 NCB855E/NCB855PRO/NCB858 l Guía de inicio rápido
Conformidad
Este equipo cumple con los siguientes requisitos mostrados a
continuación:
FCC Apartado 15 Clase B
CE: Directiva de Compatibilidad Electromagnética (EMC) 2004/108/
EC de EN55022, EN61000-3-2, EN61000-3-3 y EN50130-4.
WEEE
Residuos de aparatos eléctricos y electrónicos
Deshecho correcto de este producto (aplicable en la Unión
Europea y en otros países europeos con sistemas diferentes
de recogida). Este producto debería ser retirado al nal de
su vida útil según las leyes, normativas y procedimientos
locales.

NCB855E/NCB855PRO/NCB858 l Guía de inicio rápido 3
Español
1. Introducción
Contenidos del paquete
Cámara de red ja x1
CD-ROM (Manual de usuario y Utilidad para encontrar la IP) x1
Guía de inicio rápido x1
Bloque terminal de tornillo de 2 clavijas x1
Bloque terminal de tornillo de 6 clavijas x1
Anillo de adaptador del soporte CS-C x1
Presentación del Hardware
Nombre de las piezas




1. Anillo de montaje de las lentes: Para el montaje de las lentes
en Soporte-C o Soporte-CS.
2. Control de enfoque posterior: Permite ajustar la distancia
entre la pestaña posterior de montaje de las lentes y el sensor de
imagen.
3. Conector de lentes Iris automáticas: Suministra la electricidad
y las señales de control a la lentes iris automáticas.
4. Orificio del tornillo del trípode: Utilice estos orificios de tornillo
para fijar el soporte de trípode. Puede fijar el soporte en la parte
superior o inferior. (Tornillo: 1/4”).

4 NCB855E/NCB855PRO/NCB858 l Guía de inicio rápido
Panel Posterior
Micro
SD
Card Audio Out Audio In
Reset
Power
Video
DC 12V
AC 24V
+
~~
Ethernet/PoE
1 2 3 4 5 6
RS485+
GND
ALM-In 1
ALM-In 2
RS485
ALM-Out







1. 12 V CC/24 V CA: Conecte los terminales de la electricidad a
la fuente de alimentación. Si utiliza una fuente de alimentación
CC de12V, asegúrese de que conecta el conector en la polaridad
correcta (rojo+/blanco-).
Si va a utilizar la electricidad vía Ethernet, no se usará este
conector.
2. Vídeo: Para realizar los ajsutes de enfoques e iris durante la
instalación, conecte la cámara al monitor.
3. LED de encendido: Las luces LED se encienden cuando se
suministre la fuente de alimentación.
4. Entrada de Audio: Se conecta a un micrófono externo.
5. Restaurar: Utilizando un objeto puntiagudo, presione el botón
de restauración durante menos de 5 segundos para reiniciar la
cámara. Si lo presiona durante más de 5 segundos restaurará la
cámara a los ajustes predeterminados por fábrica.
6. Salida de Audio: Se conecta a unos altavoces.
7. Ranura de tarjeta de memoria: Introduzca la tarjeta microSD/
SDHC en la ranura para la grabación y el almacenamiento.

NCB855E/NCB855PRO/NCB858 l Guía de inicio rápido 5
Español
8. I/O: Se conecta sus dispositivos externos, como sensores y
alarmas a los correspondientes bloques de la terminal I/O. Las
clavijas del bloque de la terminal I/O controla las siguientes
señales:
Clavija Señal Conexión
1 RS485+ Reservado.
2 RS485- Reservado.
3 TIE Tierra (electricidad) en circuitos
eléctricos.
4 ALM-
salida
Se conecta al dispositivo que responde a
las señales de alarma.
5 ALM-
Entrada 1
Se conecta al dispositivo que dispara las
señales de alarma.
6 ALM-
Entrada 2
Se conecta al dispositivo que dispara las
señales de alarma.
9. Ethernet/PoE: Se conecta al puerto LAN de un dispositivo
estándar 10 BaseT/100 BaseTX, como un hub, conmutador o
router.

6 NCB855E/NCB855PRO/NCB858 l Guía de inicio rápido
Dimensiones
114mm (4.5”) 66mm (2.6”)
56mm(2.2”)
65mm(2.6”)
Micro
SD
Card Audio Out Audio In
Reset
Power
Video
DC 12V
AC 24V
+
~~
Ethernet/PoE
1 2 3 4 5 6
RS485+
GND
ALM-Out ALM-In 1 ALM-In 2
RS485
2. Instalación
1. Instalación de las lentes
Fije sus lentes en el anillo de montaje de las lentes de la cámara.
Lentes con soporte CS: Fije las lentes en la cámara directamente.
Lentes con soporte S: Debe instalar primero el anillo de adaptador
de soporte CS-C suministrado y fijar a continuación las lentes de
Soporte-C.
Si está utilizando las lentes iris automáticas, conecte el cable de iris
automático al conector IRIS de la cámara.