Messoa SCB280 User manual

19 ******
20 ******
21 ******
25 ******
26 ******
27 ******
Please read this manual thoroughly before use, and keep it handy for future
29 ****** reference.
30 ******
Notes :
The technical specifications are subject to change without notice.
Power consumption increases during D/N filter switchover.
1. CAUTIONS ……………………………………………………………………
…
2
2. SYSTEM COMPONENTS ……………………………………………………
…
2
3. SYSTEM CONNECTION ……………………………………………………
…
2
4. PIN CONNECTIONS …………………………………………………………
…
3
5. PARTS NAMES & FUNCTIONS ……………………………………………
…
4
6. PUSH BUTTONS AND THEIR FUNCTIONS ………………………………
…
5
7. SETTING MENU ………………………………………………………………
…
6
8. SUB MENU ……………………………………………………………………
…
7
9. OSD FUNCTION DESCRIPTION ……………………………………………
…
8
10. SYSTEM EXTENSIONS ……………………………………………………… 11
11. SPECIFICATIONS ……………………………………………………………
…
15
ZEIM-0050696
Ver : A.1
2004.11.01
-16- -1-
MEMO
23 *
Moveable OLPF
(as shown on the next page)
*****
Optical
OSD Functions
16 Characters (OFF,TOP,BOTTOM)
(Control keys on the Side-panel of camera)
Default settings recalled by pushing DEFAULT buttom
TABLE OF CONTENTS
INSTRUCTION MANUA
L
NO
24 Iris Control Video Out / DC Iris For Galvano Lens
DC IRIS Output For Galvano Lens
Camera ID.
OSD Control
Default Setting
D/N Mode
ITEM SPECIFICATION
PAL NTSC
DC12V
AC24V
AC90V
to
AC260V
DC12V
AC24V
1/3" 1/2" 1/3" 1/2" 1/3" 1/2"
ATW1 : 2600oK ~ 6000oK
ATW2 : 2500oK ~ 9500oK
AWC : PUSH LOCK 2500oK ~ 9500oK
Manual : 64 steps by push button on R and B.
ON, OFF
AUTO, MANUAL, B.C.G
***
D/N FIL
HIGH, LOW
**White Balance
D/N LEVEL
*
22 Aperture
Correction HIGH, LOW, MID ******
28 Remote
Control(RJ-45) RS-485 (Receive / Transmit) * *****
Day&Night
Hi-Res
Colour CCD
Camera

1. Do not touch the imaging surface of sensor. Use soft cloth moistened
with alcohol to clean the surface if it is touched accidentally.
2. Ensure the supply voltage is correct as specified for the particular variant
of camera before operation.
3. Do not expose the camera to rain, moisture or to temperature outside the
specified limit, without a suitable housing.
4. Avoid focusing directly on the sun.
5. Do not attempt to service this unit yourself unless you are authorised to ***
do so. Opening the camera may expose you to dangerous voltages or ***
other hazards. Refer all servicing to qualified personnel only. **
6. If connected to the mains : **
THIS APPARATUS MUST BE EARTHED. The wires on the mains lea
d
*
are in accordance with the following code : *
GREEN/YELLOW -------------- Earth ****
BLUE ------------------------------
-
Neutral **
BROWN --------------------------
-
Live 4******
7. Warranty void if the S/N label on camera is removed. 5******
6******
******
******
1. Camera -----------------------
-
1 4. Hexagonal Wrench --------
-
1***
2. Instruction Manual ---------
-
15.
A
I Lens 4-pin Plug ---------
-
1***
3. Lens Mounting Cap -------
-
1***
***
10 ******
**
3.1 Basic System Connection :
13 ******
14 ******
15 ******
******
17 ******
-2- -15-
*
18 *
Backlight
Compensation ***
16
Manual : 1/50, 1/120, 1/250, 1/500, 1/1K, 1/2K, 1/4K, 1/10K
Sec.
Gain Control
Manual : 1/60, 1/100, 1/250, 1/500, 1/1K, 1/2K, 1/4K, 1/10K
Sec.
Shutter Control
Auto : 1/50 to 1/100000 Sec.
STD, WIDE
***
**
OFF / BLC1 / BLC2 / BLC3 / BLC4 **
130(L) x 66(W) x 55(H)
500g (max.)
Dimensions
Weights
**
Ambient -10~50℃/ 30~90% Relative Humidity
**
0.0012 Lux (F1.4,3200oK,AGC WIDE,50IRE,B/W Mode)
11
S/N Ratio
Power Source
More than 50dB
DC12V ± 10% Regulated Power Supply
AC24V ± 10% 50Hz / 60Hz ± 1Hz
AC90V to AC260V 50Hz / 60Hz
Video Output
Lens Mount
600 TV Lines (Horizontal) Night Mode
Gamma
Correction 0.45 or 1 Selectable
Resolution
CS Mount Only
480 TV Lines (Horizontal) Day Mode
12 Power
Consumption 10W (max) with AI Lens
7
0.03 Lux (F1.4,3200oK,AGC WIDE,10IRE,C/L Mode)
0.004 Lux (F1.4,3200oK,AGC WIDE,10IRE,B/W Mode)
8
9Minmum
Illumination 0.003 Lux (F1.4,3200oK,AGC WIDE,50IRE,C/L Mode)
Internal / Linelock Selectable (AC Only)
BNC Composite, RJ-45 Cat-O/P, Y/C Output
2 Pickup Elements 768(H)×494(V) Pixels 1/2" Exview Hi-Res CCD
768(H)×494(V) Pixels 1/3" Exview Hi-Res CCD
2:1 Interlace NTSC V:59.94Hz, H:15.734KHz
3Scanning
System
Sync System
1
ITEM
Image Area
SPECIFICATION
3. SYSTEM CONNECTION
2. SYSTEM COMPONENTS
1. CAUTIONS 11. SPECIFICATIONS
NO
6.5mm×4.9mm
4.9mm×3.7mm
752(H)×582(V) Pixels 1/2" Exview Hi-Res CCD
752(H)×582(V) Pixels 1/3" Exview Hi-Res CCD
2:1 Interlace PAL V:50Hz, H:15.625KHz
**
PAL NTSC
DC12V
AC24V
AC90V
to
AC260V
*
DC12V
AC24V
1/3" 1/2" 1/3" 1/2" 1/3" 1/2"
****
*
*
*
**

10.4 Conection with PC (Optional) 3.2 Extended System Connection :
TO AVOID THE RISK OF ELECTRIC SHOCK,
DO NOT LET POWER CABLES TOUCH EACH OTHER.
To connect this camera with PC and control it by PC softwar
e
(Optional). A interface converter is required for converting RS-485 to
RS-232. This converter is not a standard or optional accessory, but 4.1 IRIS Connector
it's easy to obtain in the market conditions.
4.2 RJ-45 Connector
-14- -3-
4. PIN CONNECTIONS
Function RJ-45
7
8
2
4
5
3
6
1
Pin
DATA + (RS-485)
GND
POWER(+5V) 21
DATA - (RS-485)
PREDTMSP
B/W
GND
C/L
3645 78
RS-232
Converter
RS-485
PC

10.3 B.C.G & PREDTMSP Control
1. Lens Mount (CS Mount) :
For installation of CS Mount lenses only.
2. Tripod Stand :
Application for camera mounting onto the camera holder. Effective for
general camera tripods.
3. Exposure Control :
Auto IRIS mode (two types of lens are appropriate for this function) : B.C.G function :
DC IRIS lens : Set the IRIS slide switch to the DC position and When D/N MODE set to B.C.G mode, the camera will change to
adjust the LEVEL control on the side panel to COLOUR MODE and B/W MODE manually according to a RJ-45
obtain a clear picture. B.C.G commands.
Video IRIS lens : Set the IRIS slide switch to the VIDEO positio
n
and adjust the LEVEL and ALC controls on the
lens to obtain a clear picture.
Automatic Electronic Shutter ( AES ) :
Set the IRIS slide switch to the AES position to automatically adjust
the shutter speed according to the subjects brightness.
4. V-PHASE Adjustment
When using two cameras or more, the image on the monitor may roll
vertically when switching sources. This rolling can be minimized by PDSP(PREDTMSP, Pre-determined Shutter Speed) function :
adjusting this controller. According to a RJ-45 PDSP commands, the shutter speed
5. DC IRIS LEVEL Adjustment will manually change to Pre-determined shutter speed which is set
If using a DC type auto-iris lens, you will need to set the LEVEL volume. in OSD menu.
Turn counterclockwise (L) for a darker picture. Turn clockwise (H) for
a
brighter picture.
6. Back-Focus Adjustment :
A. Back Focus Screw : Loosen this screw before using the Focus
A
djustment and to maintain correct focu
s
afterwards ensure it is tightened.
B. Focus Adjustment : Adjust this dial to obtain correct back-focus
whilst using a CS mount lens.
7. Menu / Set-up Buttons :
For menu access and adjustment.
8. Video Output Terminal (BNC) :
Used to give out the video signal. Connected to the video input terminal
of a monitor, switcher, etc. (to be terminated with 75 ohm impedance).
Note : SW1&SW2 symbolise electronic switching (PIR) or manual
switching (Voltage free contact).
-4- -13-
H (OFF) GND OFF
L (ON) GND ON
Control Terminal PREDTMSP
Pin 3 Pin 7
L (ON) H (OFF) GND Black and White
H (OFF) L (ON) GND Colour
H (OFF) H (OFF) GND Auto
L (ON) L (ON) GND
5. PARTS NAMES & FUNCTIONS
Control Terminal Image
B = Pin 6 C = Pin 4 G = Pin 5
Function RJ-45
7
8
2
4
5
3
6
1
Pin
DATA + (RS-485)
GND
POWER(+5V) 21
DATA - (RS-485)
PREDTMSP
B/W
GND
C/L
3645 78
( 1 )
( 3 )
( 4 )
( 2 )
GND
( 8 )
RJ45
( 6 )
( 5 )
Socket
Wall
( 7 )
SW1
Rear
SW2
C/LAUTOB/W ONOFF
GND

3. Multi-Camera Installation
10.2 Connection with Switcher Box (Optional)
To connect this camera with Switcher Box to obtain simple
control function. (B.C.G Control and PREDTMSP) On the side
p
anel of the camera, there are three
p
ush buttons as shown belo
w
-12- -5-
Menu access, function select
Function / Adjustment select (DOWN)
Continue to press more than 2 seconds to
access SUB MENU
Select
6. PUSH BUTTONS AND THEIR FUNCTION
S
Switch Name
Function / Adjustment select (UP)
Main Function
All dimensions by mm Bottom Rear
Front
Side
Top
260V
AC90~
Rear
AC24V
DC12V/
SYSTEM
MATRIX
RS-485
RS-232
PC
CAM001
CAM199
CAM002
AC/DC POWER
ADAPTOR
Rear
ON
OFF
B/W
AUTO
C/L
MODE PREDTMSP

The setting menus of hierarchy are shown below and with on-screen display. 10.1 Connection with Remote Control Box (Optional)
To connect this camera with Remote Control Box to obtain more
function. (B.C.G Control, PREDTMSP, 4 Alarm-In, 2 Alarm-Out …etc.)
1. Camera & Control Box RJ-45 Pin define :
2. Single Camera Installation :
-6- -11-
7. SETTING MENU 10. SYSTEM EXTENSION
S
COAX
CAT 5
PC
RS-232
AC/DC POWER
ADAPTOR
Function RJ-45
7
8
2
4
5
3
6
1
Pin
DATA + (RS-485)
GND
POWER(+5V) 21
DATA - (RS-485)
PREDTMSP
B/W
GND
C/L
3645 7 8
MENU
GAIN
SYNC
GAMMA
BLC
WHITE
APERTURE
PREDTMSP
STD
SHUTTER AUTO 1/50
(
PAL
);
1/60
(
NTSC
)
1/2501/500
1/10K 1/4K 1/2K 1/1K
D/N MODE AUTO B.C.GMANUA
D/N LEVEL HIGH LOW
D/N FIL ON OFF
WIDE
INT LL
0.45 1
OFF BLC1 BLC2 BLC3 BLC4
ATW1 ATW2 AWC R:0~6 B:0~6
HIGH LOW MID
ID.
ID POS
NEXT/BAC
■■■■■■■■■■■■■
OFF TOP BOTTO
EXIT CANCEL DEFAULT
Default Setting
1/120
(
PAL
);
1/100
(
NTSC
)
OFF 1/50
(
PAL
);
1/60
(
NTSC
)
1/2501/500
1/10K 1/4K 1/2K 1/1K
1/120
(
PAL
);
1/100
(
NTSC
)

12. ID. :
16 characters Max. (alpha-numeric).
Using to name each camera. Press and hold the ↑button on the side of the camera body for about
2
13. ID POS : seconds until the menu appears on the monitor. The blinking area represents
OFF : No ID display. the option to be set.
TOP : Display the ID in the top left of screen.
BOTTOM : Display the ID in the bottom left of screen.
14. NEXT BACK :
Selection of next page and last page.
15. EXIT :
Save all settings and exit.
16. CANCEL :
Reset back to original settings.
17. DEFAULT :
Recall factory settings.
9.2 SUB MENU
1. ADDRESS :
Setting address from 001 to 199 for communication with remote
controller.
2. PROTOCOL :
Select protocol for communication with remote controller.
PELCO P, PELCO D and ERNITEC are able to select.
3. LANGUAGE :
Select language of OSD. English, Francais, German are able to select.
4. BIT RATE :
Setting bit rate of data transmission. In RS-485 control, it is necessary
to set a unique camera address and bit rate for each camera. Note : All of functions in SUB MENU are used for connection with remote
1200, 2400, 4800, 9600 are able to select. control box (Optional) or PC Software.
5. SOFT VER :
Software version display.
Note : All of functions in SUB MENU are used for connection with remote
control box (Optional) or PC Software. 9.1 SETTING MENU
1. D/N MODE :
AUTO : When set to this mode, the camera will change to COLOUR
mode and B/W mode automatically according to a subject's
brightness.
MANUAL When set to this mode, the camera will remain in COLOUR
or B/W mode by MANUAL selection.
B.C.G : When set to this mode, the camera will change to COLOUR
mode and B/W mode manually according to a RJ-45 B,C,G
commands.
-10- -7-
8. SUB MENU
9. OSD FUNCTION DESCRIPTION
SUB
MENU
001 199
Default Setting
ADDRESS
PELCO P PELCO D
PROTOCOL
1200
BIT RATE 2400 4800 9600
SOFT VER
EXIT DEFAULT
ERNITEC
LANGUAGE ENGLISH FRANCAIS GERMAN

2. D/N LEVEL : BLC2 : Backlight compensation window is like
Set u
p
a switch-over
p
oint from B/W mode to COLOUR mode.
Use the SELECT button to select HIGH or LOW Under the AUTO
mode, the switchover point of brightness from COLOUR mode to
B/W is 1.5 lux.
LOW : The switchover point of brightness from B/W to COLOUR
mode is 4.5 lux. (Centre Window)
HIGH : The switchover point of brightness from B/W to COLOUR
mode is 7.5 lux.
BLC3 : Backlight compensation window is like
( To switch between Colour mode and B/W mode withina short time,
use this setup.)
3. D/N FIL :
ON : Y-signal filter of CCD output is narrow in B/W mode. In this
p
osition, the horizontal resoulation is 480TV line
s
OFF : Y-signal filter of CCD output is wide in B/W mode. In this (Bottom Window)
p
osition, the horizontal resoulation is 600TV line
s
(If there is horizontal noise in B/W mode,set to ON)
4. SHUTTER : BLC4 : Backlight compensation window is like
Selection of shutter speed from AUTO to 1/10K. Sequentially
contains AUTO, 1/50(PAL) or 1/60(NTSC), 1/120(PAL) or 1/100(NTSC)
, 1/250, 1/500, 1/1K, 1/2K, 1/4K, 1/10K.
When the slide switch is set to :
AES Mode : Shutter will be able to select from AUTO to 1/10K
DC/VIDEO Mode : Shutter will be able to select from 1/50(PAL) o
r
(Top Window)
1/60(NTSC) to 1/10K.
5. GAIN :
STD : Standard position, GAIN=22dB. 9. WHITE BAL :
WIDE : High-sensitivity position, GAIN=30dB. ATW1(INDOOR) :
6. SYNC : TTL auto trace white balance algorithm is designed to implement a
INT : The camera is in the internal SYNC mode. perfect colour reproduction. Colour temperature range is 2600
oK~6000oK.
LL : The camera is in the LineLock Mode. ATW2(OUTDOOR) :
Adjusting degrees by V-PHASE control on the side panel. TTL auto trace white balance algorithm is designed to implement a
7. GAMMA : perfect colour reproduction. Colour temperature range is 2500
oK~9500oK.
Selection of GAMMA curvature for GAMMA correction. AWC :
0.45 and 1 are able to select. The white balance is automatically adjusted, within 3 seconds, to the
8. BLC : correct colour temperature of the environment.
Selection of backlight compensation mode. MANUAL :
OFF : The BLC function is off. Manually adjust the R and B (red&blue) values.
BLC1 : Backlight compensation window is like 10. APERTURE :
Selection of picture sharpness (HIGH, LOW, MID).
11. PDSP :
(Pre-determined shutter speed)
Preset of shutter speed. When external controler active this functon,
shutter speed will be change to preset value.
(Bottom-Centre Window) (Manually according to a RJ-45 PREDTMSP command.)
-8- -9-

2. D/N LEVEL : BLC2 : Backlight compensation window is like
Set u
p
a switch-over
p
oint from B/W mode to COLOUR mode.
Use the SELECT button to select HIGH or LOW Under the AUTO
mode, the switchover point of brightness from COLOUR mode to
B/W is 1.5 lux.
LOW : The switchover point of brightness from B/W to COLOUR
mode is 4.5 lux. (Centre Window)
HIGH : The switchover point of brightness from B/W to COLOUR
mode is 7.5 lux.
BLC3 : Backlight compensation window is like
( To switch between Colour mode and B/W mode withina short time,
use this setup.)
3. D/N FIL :
ON : Y-signal filter of CCD output is narrow in B/W mode. In this
p
osition, the horizontal resoulation is 480TV line
s
OFF : Y-signal filter of CCD output is wide in B/W mode. In this (Bottom Window)
p
osition, the horizontal resoulation is 600TV line
s
(If there is horizontal noise in B/W mode,set to ON)
4. SHUTTER : BLC4 : Backlight compensation window is like
Selection of shutter speed from AUTO to 1/10K. Sequentially
contains AUTO, 1/50(PAL) or 1/60(NTSC), 1/120(PAL) or 1/100(NTSC)
, 1/250, 1/500, 1/1K, 1/2K, 1/4K, 1/10K.
When the slide switch is set to :
AES Mode : Shutter will be able to select from AUTO to 1/10K
DC/VIDEO Mode : Shutter will be able to select from 1/50(PAL) o
r
(Top Window)
1/60(NTSC) to 1/10K.
5. GAIN :
STD : Standard position, GAIN=22dB. 9. WHITE BAL :
WIDE : High-sensitivity position, GAIN=30dB. ATW1(INDOOR) :
6. SYNC : TTL auto trace white balance algorithm is designed to implement a
INT : The camera is in the internal SYNC mode. perfect colour reproduction. Colour temperature range is 2600
oK~6000oK.
LL : The camera is in the LineLock Mode. ATW2(OUTDOOR) :
Adjusting degrees by V-PHASE control on the side panel. TTL auto trace white balance algorithm is designed to implement a
7. GAMMA : perfect colour reproduction. Colour temperature range is 2500
oK~9500oK.
Selection of GAMMA curvature for GAMMA correction. AWC :
0.45 and 1 are able to select. The white balance is automatically adjusted, within 3 seconds, to the
8. BLC : correct colour temperature of the environment.
Selection of backlight compensation mode. MANUAL :
OFF : The BLC function is off. Manually adjust the R and B (red&blue) values.
BLC1 : Backlight compensation window is like 10. APERTURE :
Selection of picture sharpness (HIGH, LOW, MID).
11. PDSP :
(Pre-determined shutter speed)
Preset of shutter speed. When external controler active this functon,
shutter speed will be change to preset value.
(Bottom-Centre Window) (Manually according to a RJ-45 PREDTMSP command.)
-8- -9-

12. ID. :
16 characters Max. (alpha-numeric).
Using to name each camera. Press and hold the ↑button on the side of the camera body for about
2
13. ID POS : seconds until the menu appears on the monitor. The blinking area represents
OFF : No ID display. the option to be set.
TOP : Display the ID in the top left of screen.
BOTTOM : Display the ID in the bottom left of screen.
14. NEXT BACK :
Selection of next page and last page.
15. EXIT :
Save all settings and exit.
16. CANCEL :
Reset back to original settings.
17. DEFAULT :
Recall factory settings.
9.2 SUB MENU
1. ADDRESS :
Setting address from 001 to 199 for communication with remote
controller.
2. PROTOCOL :
Select protocol for communication with remote controller.
PELCO P, PELCO D and ERNITEC are able to select.
3. LANGUAGE :
Select language of OSD. English, Francais, German are able to select.
4. BIT RATE :
Setting bit rate of data transmission. In RS-485 control, it is necessary
to set a unique camera address and bit rate for each camera. Note : All of functions in SUB MENU are used for connection with remote
1200, 2400, 4800, 9600 are able to select. control box (Optional) or PC Software.
5. SOFT VER :
Software version display.
Note : All of functions in SUB MENU are used for connection with remote
control box (Optional) or PC Software. 9.1 SETTING MENU
1. D/N MODE :
AUTO : When set to this mode, the camera will change to COLOUR
mode and B/W mode automatically according to a subject's
brightness.
MANUAL When set to this mode, the camera will remain in COLOUR
or B/W mode by MANUAL selection.
B.C.G : When set to this mode, the camera will change to COLOUR
mode and B/W mode manually according to a RJ-45 B,C,G
commands.
-10- -7-
8. SUB MENU
9. OSD FUNCTION DESCRIPTION
SUB
MENU
001 199
Default Setting
ADDRESS
PELCO P PELCO D
PROTOCOL
1200
BIT RATE 2400 4800 9600
SOFT VER
EXIT DEFAULT
ERNITEC
LANGUAGE ENGLISH FRANCAIS GERMAN

The setting menus of hierarchy are shown below and with on-screen display. 10.1 Connection with Remote Control Box (Optional)
To connect this camera with Remote Control Box to obtain more
function. (B.C.G Control, PREDTMSP, 4 Alarm-In, 2 Alarm-Out …etc.)
1. Camera & Control Box RJ-45 Pin define :
2. Single Camera Installation :
-6- -11-
7. SETTING MENU 10. SYSTEM EXTENSION
S
COAX
CAT 5
PC
RS-232
AC/DC POWER
ADAPTOR
Function RJ-45
7
8
2
4
5
3
6
1
Pin
DATA + (RS-485)
GND
POWER(+5V) 21
DATA - (RS-485)
PREDTMSP
B/W
GND
C/L
3645 7 8
MENU
GAIN
SYNC
GAMMA
BLC
WHITE
APERTURE
PREDTMSP
STD
SHUTTER AUTO 1/50
(
PAL
);
1/60
(
NTSC
)
1/2501/500
1/10K 1/4K 1/2K 1/1K
D/N MODE AUTO B.C.GMANUA
D/N LEVEL HIGH LOW
D/N FIL ON OFF
WIDE
INT LL
0.45 1
OFF BLC1 BLC2 BLC3 BLC4
ATW1 ATW2 AWC R:0~6 B:0~6
HIGH LOW MID
ID.
ID POS
NEXT/BAC
■■■■■■■■■■■■■
OFF TOP BOTTO
EXIT CANCEL DEFAULT
Default Setting
1/120
(
PAL
);
1/100
(
NTSC
)
OFF 1/50
(
PAL
);
1/60
(
NTSC
)
1/2501/500
1/10K 1/4K 1/2K 1/1K
1/120
(
PAL
);
1/100
(
NTSC
)

3. Multi-Camera Installation
10.2 Connection with Switcher Box (Optional)
To connect this camera with Switcher Box to obtain simple
control function. (B.C.G Control and PREDTMSP) On the side
p
anel of the camera, there are three
p
ush buttons as shown belo
w
-12- -5-
Menu access, function select
Function / Adjustment select (DOWN)
Continue to press more than 2 seconds to
access SUB MENU
Select
6. PUSH BUTTONS AND THEIR FUNCTION
S
Switch Name
Function / Adjustment select (UP)
Main Function
All dimensions by mm Bottom Rear
Front
Side
Top
260V
AC90~
Rear
AC24V
DC12V/
SYSTEM
MATRIX
RS-485
RS-232
PC
CAM001
CAM199
CAM002
AC/DC POWER
ADAPTOR
Rear
ON
OFF
B/W
AUTO
C/L
MODE PREDTMSP

10.3 B.C.G & PREDTMSP Control
1. Lens Mount (CS Mount) :
For installation of CS Mount lenses only.
2. Tripod Stand :
Application for camera mounting onto the camera holder. Effective for
general camera tripods.
3. Exposure Control :
Auto IRIS mode (two types of lens are appropriate for this function) : B.C.G function :
DC IRIS lens : Set the IRIS slide switch to the DC position and When D/N MODE set to B.C.G mode, the camera will change to
adjust the LEVEL control on the side panel to COLOUR MODE and B/W MODE manually according to a RJ-45
obtain a clear picture. B.C.G commands.
Video IRIS lens : Set the IRIS slide switch to the VIDEO positio
n
and adjust the LEVEL and ALC controls on the
lens to obtain a clear picture.
Automatic Electronic Shutter ( AES ) :
Set the IRIS slide switch to the AES position to automatically adjust
the shutter speed according to the subjects brightness.
4. V-PHASE Adjustment
When using two cameras or more, the image on the monitor may roll
vertically when switching sources. This rolling can be minimized by PDSP(PREDTMSP, Pre-determined Shutter Speed) function :
adjusting this controller. According to a RJ-45 PDSP commands, the shutter speed
5. DC IRIS LEVEL Adjustment will manually change to Pre-determined shutter speed which is set
If using a DC type auto-iris lens, you will need to set the LEVEL volume. in OSD menu.
Turn counterclockwise (L) for a darker picture. Turn clockwise (H) for
a
brighter picture.
6. Back-Focus Adjustment :
A. Back Focus Screw : Loosen this screw before using the Focus
A
djustment and to maintain correct focu
s
afterwards ensure it is tightened.
B. Focus Adjustment : Adjust this dial to obtain correct back-focus
whilst using a CS mount lens.
7. Menu / Set-up Buttons :
For menu access and adjustment.
8. Video Output Terminal (BNC) :
Used to give out the video signal. Connected to the video input terminal
of a monitor, switcher, etc. (to be terminated with 75 ohm impedance).
Note : SW1&SW2 symbolise electronic switching (PIR) or manual
switching (Voltage free contact).
-4- -13-
H (OFF) GND OFF
L (ON) GND ON
Control Terminal PREDTMSP
Pin 3 Pin 7
L (ON) H (OFF) GND Black and White
H (OFF) L (ON) GND Colour
H (OFF) H (OFF) GND Auto
L (ON) L (ON) GND
5. PARTS NAMES & FUNCTIONS
Control Terminal Image
B = Pin 6 C = Pin 4 G = Pin 5
Function RJ-45
7
8
2
4
5
3
6
1
Pin
DATA + (RS-485)
GND
POWER(+5V) 21
DATA - (RS-485)
PREDTMSP
B/W
GND
C/L
3645 78
( 1 )
( 3 )
( 4 )
( 2 )
GND
( 8 )
RJ45
( 6 )
( 5 )
Socket
Wall
( 7 )
SW1
Rear
SW2
C/LAUTOB/W ONOFF
GND

10.4 Conection with PC (Optional) 3.2 Extended System Connection :
TO AVOID THE RISK OF ELECTRIC SHOCK,
DO NOT LET POWER CABLES TOUCH EACH OTHER.
To connect this camera with PC and control it by PC softwar
e
(Optional). A interface converter is required for converting RS-485 to
RS-232. This converter is not a standard or optional accessory, but 4.1 IRIS Connector
it's easy to obtain in the market conditions.
4.2 RJ-45 Connector
-14- -3-
4. PIN CONNECTIONS
Function RJ-45
7
8
2
4
5
3
6
1
Pin
DATA + (RS-485)
GND
POWER(+5V) 21
DATA - (RS-485)
PREDTMSP
B/W
GND
C/L
3645 78
RS-232
Converter
RS-485
PC

1. Do not touch the imaging surface of sensor. Use soft cloth moistened
with alcohol to clean the surface if it is touched accidentally.
2. Ensure the supply voltage is correct as specified for the particular variant
of camera before operation.
3. Do not expose the camera to rain, moisture or to temperature outside the
specified limit, without a suitable housing.
4. Avoid focusing directly on the sun.
5. Do not attempt to service this unit yourself unless you are authorised to ***
do so. Opening the camera may expose you to dangerous voltages or ***
other hazards. Refer all servicing to qualified personnel only. **
6. If connected to the mains : **
THIS APPARATUS MUST BE EARTHED. The wires on the mains lea
d
*
are in accordance with the following code : *
GREEN/YELLOW -------------- Earth ****
BLUE ------------------------------
-
Neutral **
BROWN --------------------------
-
Live 4******
7. Warranty void if the S/N label on camera is removed. 5******
6******
******
******
1. Camera -----------------------
-
1 4. Hexagonal Wrench --------
-
1***
2. Instruction Manual ---------
-
15.
A
I Lens 4-pin Plug ---------
-
1***
3. Lens Mounting Cap -------
-
1***
***
10 ******
**
3.1 Basic System Connection :
13 ******
14 ******
15 ******
******
17 ******
-2- -15-
*
18 *
Backlight
Compensation ***
16
Manual : 1/50, 1/120, 1/250, 1/500, 1/1K, 1/2K, 1/4K, 1/10K
Sec.
Gain Control
Manual : 1/60, 1/100, 1/250, 1/500, 1/1K, 1/2K, 1/4K, 1/10K
Sec.
Shutter Control
Auto : 1/50 to 1/100000 Sec.
STD, WIDE
***
**
OFF / BLC1 / BLC2 / BLC3 / BLC4 **
130(L) x 66(W) x 55(H)
500g (max.)
Dimensions
Weights
**
Ambient -10~50℃/ 30~90% Relative Humidity
**
0.0012 Lux (F1.4,3200oK,AGC WIDE,50IRE,B/W Mode)
11
S/N Ratio
Power Source
More than 50dB
DC12V ± 10% Regulated Power Supply
AC24V ± 10% 50Hz / 60Hz ± 1Hz
AC90V to AC260V 50Hz / 60Hz
Video Output
Lens Mount
600 TV Lines (Horizontal) Night Mode
Gamma
Correction 0.45 or 1 Selectable
Resolution
CS Mount Only
480 TV Lines (Horizontal) Day Mode
12 Power
Consumption 10W (max) with AI Lens
7
0.03 Lux (F1.4,3200oK,AGC WIDE,10IRE,C/L Mode)
0.004 Lux (F1.4,3200oK,AGC WIDE,10IRE,B/W Mode)
8
9Minmum
Illumination 0.003 Lux (F1.4,3200oK,AGC WIDE,50IRE,C/L Mode)
Internal / Linelock Selectable (AC Only)
BNC Composite, RJ-45 Cat-O/P, Y/C Output
2 Pickup Elements 768(H)×494(V) Pixels 1/2" Exview Hi-Res CCD
768(H)×494(V) Pixels 1/3" Exview Hi-Res CCD
2:1 Interlace NTSC V:59.94Hz, H:15.734KHz
3Scanning
System
Sync System
1
ITEM
Image Area
SPECIFICATION
3. SYSTEM CONNECTION
2. SYSTEM COMPONENTS
1. CAUTIONS 11. SPECIFICATIONS
NO
6.5mm×4.9mm
4.9mm×3.7mm
752(H)×582(V) Pixels 1/2" Exview Hi-Res CCD
752(H)×582(V) Pixels 1/3" Exview Hi-Res CCD
2:1 Interlace PAL V:50Hz, H:15.625KHz
**
PAL NTSC
DC12V
AC24V
AC90V
to
AC260V
*
DC12V
AC24V
1/3" 1/2" 1/3" 1/2" 1/3" 1/2"
****
*
*
*
**

19 ******
20 ******
21 ******
25 ******
26 ******
27 ******
Please read this manual thoroughly before use, and keep it handy for future
29 ****** reference.
30 ******
Notes :
The technical specifications are subject to change without notice.
Power consumption increases during D/N filter switchover.
1. CAUTIONS ……………………………………………………………………
…
2
2. SYSTEM COMPONENTS ……………………………………………………
…
2
3. SYSTEM CONNECTION ……………………………………………………
…
2
4. PIN CONNECTIONS …………………………………………………………
…
3
5. PARTS NAMES & FUNCTIONS ……………………………………………
…
4
6. PUSH BUTTONS AND THEIR FUNCTIONS ………………………………
…
5
7. SETTING MENU ………………………………………………………………
…
6
8. SUB MENU ……………………………………………………………………
…
7
9. OSD FUNCTION DESCRIPTION ……………………………………………
…
8
10. SYSTEM EXTENSIONS ……………………………………………………… 11
11. SPECIFICATIONS ……………………………………………………………
…
15
ZEIM-0050696
Ver : A.1
2004.11.01
-16- -1-
MEMO
23 *
Moveable OLPF
(as shown on the next page)
*****
Optical
OSD Functions
16 Characters (OFF,TOP,BOTTOM)
(Control keys on the Side-panel of camera)
Default settings recalled by pushing DEFAULT buttom
TABLE OF CONTENTS
INSTRUCTION MANUA
L
NO
24 Iris Control Video Out / DC Iris For Galvano Lens
DC IRIS Output For Galvano Lens
Camera ID.
OSD Control
Default Setting
D/N Mode
ITEM SPECIFICATION
PAL NTSC
DC12V
AC24V
AC90V
to
AC260V
DC12V
AC24V
1/3" 1/2" 1/3" 1/2" 1/3" 1/2"
ATW1 : 2600oK ~ 6000oK
ATW2 : 2500oK ~ 9500oK
AWC : PUSH LOCK 2500oK ~ 9500oK
Manual : 64 steps by push button on R and B.
ON, OFF
AUTO, MANUAL, B.C.G
***
D/N FIL
HIGH, LOW
**White Balance
D/N LEVEL
*
22 Aperture
Correction HIGH, LOW, MID ******
28 Remote
Control(RJ-45) RS-485 (Receive / Transmit) * *****
Lens not included
Day&Night
Hi-Res
Colour CCD
Camera