Metra Electronics 99-6507 User manual

installation instructions for Part 99-6507
Phillips Screwdriver • Socket Wrench •
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
CHRYSLER
300 2005-2007
Aspen 2007
PT Cruiser 2006-2009
JEEP
Comman er 2006-2007
Compass 2007-2008
Gran Cherokee 2005-2007
Patriot 2007-2008
TOOLS REQUIRED:
APPLICATIONS
Small Flat Blade Screwdriver or
Panel Removal Tool
A) Radio Housing • B) ISO Snap-In Brackets • C) Trim Plates (upper & lower)
KIT COMPONENTS
A
B
Lower Trim Plate
Upper Trim Plate
C
DODGE
Caliber 2007-2008
Charger 2005-2007
Dakota 2005-2007
Durango 2004-2007
Magnum 2005-2007
Ram 2006-2008
Ram 2500/3500 2009
MITSUBISHI
Rai er 2006-2007
NOTE: NON NAV MODELS ONLY
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
• CHTO-01 - Chrysler amp inter ace harness 2004-up
• XSVI-6502-NAV - Chrysler R.A.P. harness 2004-up
Antenna Adapter:
• 40-CR10 - Chrysler antenna adapter 2002-up
KIT FEATURES
• DIN Radio Provision with Pocket
• ISO DIN Radio Provision with Pocket
99-6507

Dash Disassembly
- Chrysler Aspen 2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
- Dodge Dakota 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
- Dodge Durango 2004-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
- Dodge Charger 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
- Dodge Magnum 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
- Chrysler 300 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
- Dodge Ram 2006-2008 (Without Center Console) . . . . . . . . . . . . . . . . . . . . . . 4
- Dodge Ram 2006-2008 (With Mini Center Console) . . . . . . . . . . . . . . . . . . . . . 5
- Dodge Ram 2006-2008 (With Full Center Console) . . . . . . . . . . . . . . . . . . . . . 6
- Dodge Caliber 2007-2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
- Jeep Compass 2007-2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
- Jeep Patriot 2007-2008 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
- Jeep Grand Cherokee 2005-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
- Jeep Commander 2006-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
- Chrysler P Cruiser 2006-2009 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
- Mitsubishi Raider 2006-2007 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Kit Assembly
- DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
- ISO Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
taBlE of contEnts
99-6507
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take
steps toward a better tomorrow.

1
99-6507 DasH DisassEMBlY
DoDgE Dakota 2005-2007
cHrYslEr asPEn 2007
Disconnect the negative battery terminal
to prevent an accidental short circuit.
Remove (2) 7MM screws from the inside
of the pocket facing upward. (Figure A)
1
2
Unclip and remove the entire trim panel
surrounding the radio and climate controls.
(Figure B)
3
Remove (4) 7MM screws securing radio.
Unplug and remove radio.(Figure C)
4
A
B
C
Continue to kit assembly.
5
DoDgE Durango 2004-2007

2
99-6507 DasH DisassEMBlY
DoDgE MagnuM 2005-2007
DoDgE cHargEr 2005-2007
Disconnect the negative battery terminal
to prevent an accidental short circuit.
Unclip and remove entire panel surrounding
radio and climate controls, including a/c
vents. (Figure A)
1
2
Remove (4) 7MM screws securing radio.
Unplug and remove radio. (Figure B)
3
A
B
Continue to kit assembly.
4

99-6507 DasH DisassEMBlY
3
cHrYslEr 300 2005-2007
Disconnect the negative battery terminal
to prevent an accidental short circuit.
Unclip and remove entire panel surround-
ing radio and climate controls, including
a/c vents and clock. (Figure A)
1
2
Remove (4) 7MM screws securing radio.
Unplug and remove radio. (Figure B)
3B
A
Continue to kit assembly.
4

99-6507 DasH DisassEMBlY
4
DoDgE raM 2006-2008
Disconnect the negative battery terminal
to prevent an accidental short circuit.
Open cup holder and remove (2) hillips
screws facing up on front edge of
radio/climate control panel. (Figure A)
1
2
Unclip and remove entire panel sur-
rounding radio and climate controls,
including a/c vents. (Figure B)
3
Remove (4) 7MM screws securing radio.
Unplug and remove radio.
4
A
B
witHout cEntEr consolE
Continue to kit assembly.
5

99-6507 DasH DisassEMBlY
5
DoDgE raM 2006-2008
Disconnect the negative battery terminal
to prevent an accidental short circuit.
Remove center console inserts, if present.
(Figure A)
1
3
Unclip and remove entire panel sur-
rounding radio and climate controls,
including a/c vents. (Figure E)
8
Remove (4) 7MM screws securing radio
to dash and remove radio.
9
A
B
If vehicle has floor shifter, remove shifter
knob.
2
C
witH Mini cEntEr consolE
DE
Remove screws securing the rear center
console to the floor panel. Lift up on the
rear center console to clear the gear shift
lever, if present. (Figure B)
4
Remove screws securing the front center
console to the floor panel. Unclip and
remove the front center console.
(Figure C)
5
Remove two phillips head screws at bottom
of dash. Unsnap and remove lower panel.
6
Remove (2) hillips screws facing up on
front edge of radio/climate control panel.
(Figure D)
7
Continue to kit assembly.
10

99-6507 DasH DisassEMBlY
6
Disconnect the negative battery terminal
to prevent an accidental short circuit.
Unsnap and remove console front top
cover (closest to the dash). (Figure A)
1
3
Unclip and remove entire panel surrounding
radio and climate controls, including a/c
vents. (Figure D)
7
Remove (4) 7MM screws securing radio
to dash and remove radio.
8
A
B
If vehicle has floor shifter, remove shifter
knob.
2
C
D
Remove two 8 mm screws from under
console cover (previously removed).
Remove front section of console.
(Figure B)
4
5Loosen two 8 mm screws at bottom of
dash. Unsnap lower panel.
Remove (2) hillips screws facing up on
front edge of radio/climate control panel.
(Figure C)
6
Continue to kit assembly.
9
DoDgE raM 2006-2008
witH full cEntEr consolE

99-6507 DasH DisassEMBlY
7
DoDgE caliBEr 2007-2008
JEEP coMPass 2007-2008
JEEP Patriot 2007-2008
123 4 56
L
D
L
D
N
R
P
A
Disconnect the negative battery terminal
to prevent an accidental short circuit.
Unsnap and move shifter trim to the side.
(Figure A)
1
2
4
Remove (4) 7MM screws securing radio.
Unplug and remove radio.
6
Continue to kit assembly.
Unsnap center dash trim panel (do not
remove until climate controls are
removed). (Figure A)
5Remove (4) hillips screws holding
climate control panel to backside of
the center dash panel.
7
3(Compass and atriot only) Unspap and
remove top center dash panel above AC
vents.

8
99-6507 DasH DisassEMBlY
JEEP granD cHErokEE 2005-2007
Disconnect the negative battery terminal
to prevent an accidental short circuit.
Unsnap and remove panel from around
radio including the vent on each side.
(Figure A)
1
2
Remove (4) 7MM screws securing radio.
Unplug and remove radio. (Figure B)
3
A
B
Continue to kit assembly.
4

9
99-6507 DasH DisassEMBlY
JEEP coMManDEr 2006-2007
4 screws 4 screws 4 screws 4 screws
A
B
Disconnect the negative battery terminal
to prevent an accidental short circuit.
Remove the (16) screws securing the
radio trim panel. (Figure A)
1
2
Unclip and remove the entire radio trim
panel. (Figure B)
3
Remove (4) 7MM screws securing radio. Unplug and remove radio.
4
Continue to kit assembly.
5

99-6507 DasH DisassEMBlY
10
cHrYslEr Pt cruisEr 2006-2009
Disconnect the negative battery terminal
to prevent an accidental short circuit.
Remove (2) screws from inside air vents
on center dash panel. (Figure A)
1
2
3
Remove (4) 7MM screws securing radio.
Unplug and remove radio.
6
A
Continue to kit assembly.
Unsnap center dash panel (do not remove
until climate controls are removed).
(Figure A)
4Remove (4) hillips screws holding climate
control panel to backside of the center
dash panel.
5Remove (4) hillips screws holding climate
control panel to backside of the center
dash panel.
7

99-6507 DasH DisassEMBlY
11
MitsuBisHi raiDEr 2006-2007
Disconnect the negative battery terminal
to prevent an accidental short circuit.
Unsnap and remove center dash panel.
(Figure A)
1
2
3Remove (4) 7MM screws securing radio.
Unplug and remove radio.
4
A
Continue to kit assembly.

12
99-6507 kit assEMBlY
Din raDio Pro ision witH PockEt
B
C
A
1
Slide the DIN cage into the Radio
Housing and secure by bending
the metal locking tabs down.
(
Figure A)
2
Slide the after-market head unit into
the cage and secure. (
Figure B)
3
Using the alignment pins on the
trim plates & the corresponding
holes in the housing, attach the
upper trim plate and the lower trim
plate supplied with the kit.
Figure C
NOTE: You will need to remove the
aftermarket radio’s trim ring if
equipped.
4
Continue to Final Assembly.

13
99-6507
kit assEMBlY
iso raDio Pro ision witH PockEt
1
Mount the ISO Brackets to the
radio using the screws supplied
with the radio.
Figure A
2
Slide the radio into the opening
until it snaps into place.
Figure B
3
Using the alignment pins on the
trim plates & the corresponding
holes in the housing, attach the
upper trim plate and the lower trim
plate supplied with the kit.
Figure B
A
B
NOTE: You will need to remove the
aftermarket radio’s trim ring if
equipped.
4
Continue to Final Assembly.

99-6507
final assEMBlY
final assEMBlY
1
Locate the actory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown.
(Isolate and individually tape o the ends o any unused wires to prevent
electrical short circuit.)
3
Re-connect the negative battery terminal and test the unit or proper operation.
4
Reassemble radio and dash assemblies in reverse order o disassembly.
A
A) Strip wire ends back 1/2"
B) wist ends together
C) Solder
D) ape
B
C
D
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
ower Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer . . . . . . . . . . Orange / White
Right Front (+) . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
METRA / EIA WIRING CODE
FINAL WIRING CONNECTIONS
Secure the kit into the sub dash using the (4) 7mm screws that secured
the factory radio.
2
1-800-221-0932 www.metraonline.com
REV. 06/30/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-6507