Metra Electronics 99-8724B User manual

CAUTION! All accessories, switches, climate
controls panels, and especially air bag indicator
lights must be connected before cycling the
ignition. Also, do not remove the factory radio
with the key in the on position, or while the
vehicle is running.
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV.8/27/18 INST99-8724B
INSTALLATION INSTRUCTIONS
99-8724B
KIT FEATURES
• ISO DIN radio provision with pocket
• ISO DDIN radio provision
• Painted matte black
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Pocket • D) (8) #8 x 3/8” Phillips screws
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Socket wrench • T-20 Torx screwdriver
TABLE OF CONTENTS
Dash Disassembly ..................................................2
Kit Assembly
–ISO DIN radio provision with pocket ..................3
–ISO DDIN radio provision .....................................3
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: XSVI-9005-NAV
Antenna Adapter: 40-EU10
Steering Wheel Control Interface: ASWC-1
A B C D
Mercedes-Benz CLK-Class 2005-2009

1.800.221.0932
|
MetraOnline.com
2
1. Unclip the shifter trim panel, then unclip
the shifter boot from the panel. Slide
the shifter boot through the panel, then
unplug and remove the panel. (Figure A)
2. Unclip the ashtray and set to the side.
(Figure B)
3. Remove (2) T-20 Torx screws securing the
bottom of the climate control panel, then
unplug and remove the panel. (Figure C)
(Figure D)
(Figure E)
DASH DISASSEMBLY
(Figure A)
(Figure B)
(Figure C)
4. Open the cup-holder, then unclip,
unplug, and remove the hazard button
panel. (Figure D)
5. Remove (4) T-20 Torx screws securing the
radio, then unplug and remove the radio.
(Figure E)
Continue to Kit Assembly

REV. 8/27/2018 INST99-8724B 3
(Figure A)
(Figure B)
(Figure C)
KIT ASSEMBLY
(Figure B)
(Figure A)
ISO DIN radio provision with pocket
1. Attach the radio brackets to the radio
trim panel using (4) #8 x 3/8” Phillips
screws supplied. (Figure A)
2. Attach the pocket to the bracket
assembly using the (4) #8 x 3/8” Phillips
screws. (Figure B)
3. Remove the metal DIN sleeve and trim
ring from the aftermarket radio.
4. Slide the radio into the completed
assembly, and then secure it using
screws supplied with the radio.
(Figure C)
5. Locate the factory wiring harness and
antenna connector in the dash, and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra and/
or AXXESS. Test the radio for proper
operation.
6. Reassemble the dash in reverse order of
disassembly.
ISO DDIN radio provision
1. Attach the radio brackets to the radio
trim panel using (4) #8 x 3/8” Phillips
screws supplied. (Figure A)
2. Slide the radio into the completed
assembly, and then secure it using
screws supplied with the radio.
(Figure B)
3. Locate the factory wiring harness and
antenna connector in the dash, and
complete all necessary connections to
the radio. Metra recommends using the
proper mating adapter from Metra and/
or AXXESS. Test the radio for proper
operation.
4. Reassemble the dash in reverse order
of disassembly.

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
IMPORTANT
If you are having difficulties with the installation of this product,
please call our Tech Support line at 1-800-253-TECH. Before
doing so, look over the instructions a second time, and make
sure the installation was performed exactly as the instructions
are stated. Please have the vehicle apart and ready to perform
troubleshooting steps before calling.
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2018 METRA ELECTRONICS CORPORATION REV.8/27/18 INST99-8724B
INSTALLATION INSTRUCTIONS
99-8724B