Metra Electronics 99-8244HG User manual

APPLICATIONS
METRA. The World’s best kits.™metraonline.com1-800-221-0932 © COPYRIGHT 2014 METRA ELECTRONICS CORPORATION
REV. 7/8/2014 INST99-8244HG
CAUTION: Metra recommends disconnecting the
negative battery terminal before beginning any
installation. All accessories, switches, and especially
air bag indicator lights must be plugged in before
reconnecting the battery or cycling the ignition.
NOTE: Refer to the instructions included with the
aftermarket radio.
INSTALLATION INSTRUCTIONS FOR PART 99-8244HG
• ISO DIN radio provision with pocket
• Painted high-gloss black
• A) Radio housing • B) Radio brackets • C) Pocket • D) (1) Passenger Air Bag Light board cover • E) (2) Panel clip mounts
• F) (4) #8 x 3/8” pan-head Phillips screws • G) (7) #4 x 3/8” pan-head Phillips screws • H) (1) Air-Bag sticker (not shown)
KIT FEATURES
KIT COMPONENTS
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: • 70-1761 Toyota wire harness • TYTO-01 Toyota amplified interface
Antenna Adapter: • 40-LX11 Toyota/Lexus antenna adapter
• Panel removal tool • Phillips screwdriver
• Socket wrench
TOOLS REQUIRED
Toyota Avalon 2013-up
99-8244HG
AB C
F
D
Dash Disassembly
–Toyota Avalon 2013-up .....................................2-5
Kit Preparation ................................................. 6
Kit Assembly
–ISO DIN radio provision with pocket ...................... 7
Table of Contents
E
G

99-8244HG
2
1. Unclip and remove the a/c vent
panel above the factory radio and
surrounding the instrument cluster.
(Figure A)
Tip: Start at the passenger side
of the panel.
2. Unclip and remove the panel below
the factory radio. (Figure B)
Dash Disassembly
3. Remove (4) 10mm bolts (2 on
top and 2 on bottom) securing
the factory radio then unclip and
remove. (Figure C,D)
Continued on next page
Upper bolts
Lower bolts
(Figure A) (Figure C)
(Figure B) (Figure D)

99-8244HG
Dash Disassembly
3
4. Remove (4) small Phillips screws
securing the panel clip and screw
mount to the factory radio. Retain
for kit assembly. (Figure E)
5. Remove (9) small Phillips screws
securing the radio chassis to the
main panel of the factory radio.
(Figure F)
Continued on next page
(Figure E)
(Figure F)

99-8244HG
4
6. Remove (2) remaining Phillips
screws securing the Passenger Air
Bag Light board to the main factory
radio panel. Retain board for kit
assembly. (Figure G)
7. Remove the remaining (2) yellow
panel clips and retain for
kit assembly. (Figure H)
Continued on next page
Dash Disassembly
(Figure G)
(Figure H)

99-8244HG
5
(Figure I)
Dash Disassembly
8. Remove (2) Phillips screws and
then unclip the chrome trim around
the outside of the radio/climate
control assembly. Retain for
kit assembly. (Figure I)
9. Remove the radio brackets and the
climate control from the factory
radio. Retain climate control for
kit assembly.
Continue to kit preparation

99-8244HG
6
Kit Preparation
(Figure A)
(Figure B)
1. Attach the Passenger Air Bag Light
board to the radio housing with the
factory hardware. (Figure A)
2. Attach the Passenger Air Bag Light
board cover to the radio housing
panel over the Passenger Air Bag
Light board using (3) of the
#4 x 3/8” Phillips screws supplied.
(Figure A)
3. Apply the supplied Air Bag Sticker
to the face of the radio housing.
(Figure A)
4. Attach the panel clip and screw
mount to the radio housing using
the factory hardware. (Figure B) Step 3
Step 4
Air Bag Sticker
5. Attach the (2) panel clip mounts
to the radio housing using (4)
#4 x 3/8” Phillips screws supplied.
(Figure B)
6. Attach the clips removed in step
7 of disassembly to the panel clip
mounts on the radio housing.
7. Attach the climate control and the
chrome trim to the radio housing.
Continue to kit assembly

99-8244HG
7
Kit Assembly
(Figure A) (Figure B)
ISO DIN radio provision with pocket
1. Mount the pocket to the radio
brackets with the (4) #8 x 3/8”
Phillips screws supplied. (Figure A)
2. Slide the radio into radio brackets
and secure with the screws
supplied with the radio. (Figure B)
3. Mount the radio/pocket/bracket
assembly to the radio housing/
climate control assembly with the
factory hardware.
4. Locate the factory wiring harness
and antenna plug in the dash.
Metra recommends using the
proper mating adapters from
Metra and/or AXXESS.
5. Reassemble dash in reverse order
of disassembly.

METRA. The World’s best kits.™metraonline.com1-800-221-0932 © COPYRIGHT 2014 METRA ELECTRONICS CORPORATION
REV. 7/8/2014 INST99-8244HG
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
INSTALLATION INSTRUCTIONS FOR PART 99-8244HG

INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-8244HG
AplicAciones
METRA. The World’s best kits.™metraonline.com1-800-221-0932 © COPYRIGHT 2014 METRA ELECTRONICS CORPORATION
REV. 7/8/2014 INST99-8244HG
PRECAUCIÓN: Metra recomienda desconectar el terminal
negativo de la batería antes de comenzar cualquier
instalación. Todos los accesorios, interruptores y,
especialmente, las luces indicadoras de airbag deben
estar enchufados antes de volver a conectar la batería o
comenzar el ciclo de ignición.
Nota: Remítase a las instrucciones incluidas con el radio
de posventa.
Indice
• Herramienta para quitar paneles
• Destornillador Phillips • Llave para dados
HerrAmientAs requeridAs
• Provisión de radio ISO DIN con cavidad
•
Pintura negra de alto brillo
• A) Carcasa del radio • B) Soportes para radio • C) Cavidad • D) (1) cubierta del tablero para la luz de la bolsa de aire
del pasajero • E) (2) soportes de ganchos para panel • F) (4) tornillos Phillips de cabeza troncocónica #8 x 3/8”
• G) (7) tornillos Phillips de cabeza troncocónica #4 x 3/8” • H) (1) calcomanía de bolsa de aire (no se muestra)
cArActerísticAs del kit
componentes del kit
cABleAdo Y coneXiones de AntenA (se venden por separado)
Arnés de cables: • Arnés de cableado 70-1761 Toyota • Interfase amplificada TYTO-01 Toyota
Adaptador de antena: • Adaptador de antena 40-LX11 para Toyota/Lexus
Desmontaje del tablero
–Toyota Avalon 2013 y mas................................. 2-5
Preparación del kit ................................................ 6
Ensamble del kit
–Provisión de radio ISO DIN con cavidad .................. 7
Toyota Avalon 2013 y mas
99-8244HG
AB C
F
DE
G

99-8244HG
Desmontaje del tablero
2
1. Desenganche y quite el panel de
la rejilla de aire acondicionado de
arriba del radio de fábrica y que
rodea el tablero de instrumentos.
(Figura A)
Sugerencia: Empiece en el lado
del pasajero del panel.
2. Desenganche y quite el panel de
abajo del radio de fábrica.
(Figura B)
3. Quite los (4) pernos de 10 mm
(2 arriba y 2 abajo) que sujetan
el radio de fábrica, luego
desenganche y quite. (Figura C,D)
Continúa en la página siguiente.
Pernos superiores
Pernos inferiores
(Figura A) (Figura C)
(Figura B) (Figura D)