Metra Electronics 99-5719 User manual

METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
APPLICATIONS
KIT FEATURES
KIT COMPONENTS
TOOLS REQUIRED
1-800-221-0932 metraonline.com
METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION
REV. 1/20/2010
1-800-221-0932 metraonline.com
INSTALLATION INSTRUCTIONS FOR PART 99-5719INSTALLATION INSTRUCTIONS FOR PART 99-5719
FORD TAURUS
2004 - 2007
99-5719
• ISO & DIN Head Unit Provision w/ Pocket
• DDIN Head unit provisions
• Integrated auto climate controls and display
• Integrated passenger airbag light
• Painted Scratch Resistant Matte Black
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Pocket
• E) DDIN Brackets • F) DDIN Trim Plate • G) In-Car Temp Sensor Housing • H) Harness Extension
• Radio Removal Tool (Metra Part #86-5618) • Phillips Screwdriver
• Panel Removal Tool • Socket Set • Cutting Tool or File • T10 Torx Screwdirver
CDE
FGH
B
A

TABLE OF CONTENTS NOTES
DASH DISASSEMBLY
• FORD TAURUS 2004 - 2007 . . . . . . . . . . . 1
KIT PREPARATION
• FORD TAURUS 2004 - 2007 . . . . . . . . . . . 2
KIT ASSEMBLY
• FORD TAURUS 2004 - 2007 . . . . . . . . . 3-6
*NOTE: Refer Also to the instructions included with the aftermarket radio.
*NOTE: This product has software that can be flashed via the AXXESS
USB-CAB cable and AXXESSINTERFACE.COM. Please contact the
Metra tech support team if you feel this product is not performing
properly.
Metra recommends MECP certified
technicians
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
99-5719 99-5719

1
FORD TAURUS 2004- 2007
99-5719 DASH DISASSEMBLY
Disconnect the negative
battery terminal to prevent an
accidental short circuit.
Using Metra’s 86-5618, pull
the factory radio/climate
control panel from the dash.
(Fig. A)
Disconnect the audio system
connectors, blower motor
switch connector, vacuum
hose harness, a/c damper
door switch connector, and
potentiometer connector.
Remove the panel.
Remove (2) torx-head screws
securing the mounting clips to
the sides of the factory
radio/climate control panel
and remove the clips. (Fig. B)
Mount the clips to the
Integrated Mounting Kit with
the same torx-head screws.
1
2
3
A
B
4
5
NOTES
99-5719

2 7
Remove the In-Car temp
sensor housing from the
back of the factory control
panel. Insert into the includ-
ed In-Car temp sensor
housing and mount the
assembly under the dash.
Remove the factory rear sup-
port in the sub-dash. (Fig. A)
99-5719 KIT PREPARATION
1
2
A
Continue to Kit Assembly
FORD TAURUS 2004- 2007 FORD TAURUS 2004- 2007
2
Fig. A
Fig. B
Back
wall
Inside edge
of sub-dash
Inside edge
of sub-dash
Back
wall
99-5719
AUDIO WIRING
Open the trunk, remove (4) pop-
clips from the driver’s side trunk
liner and remove the liner. (see
Fig. A) ocate the factory tuner on
the wall of the trunk and discon-
nect the speaker and antenna plugs
(it is NOT necessary to remove
the tuner). (see Fig. B). Plug the
70-5715 into the unit speaker plug
and the antenna extension lead into
the unit antenna plug. Slide the ex-
tension harness through the space
in the back seat between the seat
back and seat bottom. Unclip the
rocker trim, tuck the extension har-
ness under the carpet and stretch
the harness to the back of the dash.
(Replace the rocker trim when
completed). Splice the speaker
leads on the extension harness into
the rear of the aftermarket head
unit. Plug the factory wiringhar-
nesses into the switch connectors
(previously mounted in step #2)
and audio connectors on the back
of the Integrated Mounting Kit.
(located under
the rear deck)
Fig. A
Fig. B

6 3
Locate the factory wiring har-
ness in the dash. Metra
recommends using the prop-
er mating adapters (included)
from Metra and AXXESS to
integrate your new radio.
Re-connect the negative bat-
tery terminal and test the unit
for proper operation.
Slide the DIN cage into the
Radio Housing and secure
by bending the metal locking
tabs down. (Fig. A)
Snap the pocket into the
bottom opening of the radio
housing. (Fig. B)
Slide the aftermarket head
unit into the cage and se-
cure. (Fig. B)
Continue to “Audio Wiring”....
1
2
3
4
A
B
FORD TAURUS 2004- 2007
DIN HEAD UNIT PROVISION
5
......... Continued from Pg.5
Snap the double DIN trim
plate into the radio housing.
(Fig. B)
Continue to “Audio Wiring”......
FORD TAURUS 2004- 2007
DDIN/STACKED ISO DIN
HEAD UNIT PROVISION
B
99-571999-5719