Metra Electronics 95-7326 User manual

INSTALLATION INSTRUCTIONS FOR PART 95-7326
95-7326
KIT FEATURES
•Double DIN Radio Provision
•Stacked ISO Mount Units Provision
A) Double DIN Trim Plate B) Double DIN Brackets
KIT COMPONENTS
A
Small Flat Blade Screwdriver/ Panel Removal Tool
•Phillips Screwdriver
1-800-221-0932
©COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
www.metraonline.com
TOOLS REQUIRED:
APPLICATIONS
Hyundai Elantra 2007-2010
(US Model Only)
(Non Radio Delete)
(Non Touring Model)
B

Dash Disassembly
-HyundaiElantra2007-2010........................................1
Kit Assembly
-DoubleDINRadioProvision .......................................2
-Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Final Assembly ..........................................4
TABLE OF CONTENTS
95-7326
*Note:
Refer also to the instructions included with the aftermarket radio.

95-7326 DASH DISASSEMBLY
HYUNDAI ELANTRA 2007 -2010
A
B
1
1
2
3
4
A/C
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip and remove the panel sur-
rounding the radio including the a/c
vents and hazard button.
(Figure A)
2
Remove (4) Phillips screws to remove
radio. (Figure B)
3
Continue to kit assembly.

2
95-7326 KIT ASSEMBLY
B
C
CUT OUT BAR
CUT HERE
A
DOUBLE DIN RADIO PROVISION
Snap the Double DIN brackets to the
inside edge of the Double DIN trim
plate.
(Figure B)
2
Slide the Double DIN radio into the
bracket/trim plate assembly and
secure the radio to the assembly using
the screws supplied with the radio.
(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Cut and remove the bar in the factory
radio trim panel. (Figure A)
1
TIP: The smoother the cut, the better
the 95-7326 will look in the dash panel.

3
95-7326 KIT ASSEMBLY
B
C
CUT OUT BAR
CUT HERE
A
STACKED ISO MOUNT UNITS PROVISION
Snap the Double DIN brackets to the
inside edge of the Double DIN trim
plate.
(Figure B)
2
Slide the stacked ISO units into the
bracket/trim plate assembly and
secure the units to the assembly using
the screws supplied with the units.
(Figure C)
3
Continue to final assembly.
*Note: Refer also to the instructions included with the aftermarket radio.
Cut and remove the bar in the factory
radio trim panel. (Figure A)
1
TIP: The smoother the cut, the better
the 95-7326 will look in the dash panel.

95-7326 FINAL ASSEMBLY
FINAL ASSEMBLY
(A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
A
B
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown. (Isolate and individ-
ually tape off the ends of any unused wires to prevent electrical short circuit.)
Re-connect the negative batteryterminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
1
2
3
4
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown belowand the instructions included with the
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and
individually tape off ends of anyunused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc. . . . . . . . . . Red
12V Batt / Memory. . . . . . . . . Yellow
Ground. . . . . . . . . . . . . . . . . . Black*
Power Antenna. . . . . . . . . . . . Blue
Amp Turn-On . . . . . . . . . . . . . Blue / White
Amp Ground. . . . . . . . . . . . . . Black / White
Illumination . . . . . . . . . . . . . . Orange
Dimmer.................Orange / White
Right Front (+) . . . . . . . . . . . . Gray
Right Front (-). . . . . . . . . . . . . Gray/ Black
Left Front (+) . . . . . . . . . . . . . White
Left Front (-). . . . . . . . . . . . . . White / Black
Right Rear (+) . . . . . . . . . . . . Violet
Right Rear (-) . . . . . . . . . . . . . Violet / Black
Left Rear (+) . . . . . . . . . . . . . Green
Left Rear (-) . . . . . . . . . . . . . . Green / Black
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.

95-7326
NOTES
5

95-7326 INSTRUCTIONS
1-800-221-0932
REV. 4/27/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST95-7326
www.metraonline.com