Metra Electronics 99-7864 User manual

METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
APPLICATIONS
1-800-221-0932 metraonline.com
INSTALLATION INSTRUCTIONS FOR PART 99-7864
REV. 11/20/17
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness:
• 70-1721 - Honda/Acura harness 1998-up
• 70-7864DZ - Accord dual zone eliminator harness 2003-2007
Antenna Adapter:
• Not required
• Flat head screwdriver • Panel removal tool • Phillips screwdriver
TOOLS REQUIRED
Honda Accord 2003-2007
99-7864
(Equipped with Single Zone Climate Controls)
• A) Radio and climate control housing • B) ISO brackets • C) ISO trim plate • D) PPH-1034 screws
KIT FEATURES
KIT COMPONENTS
B CA
• DIN radio provisions
• ISO radio provisions
D
U.S. PATENT # D519,995

Table of Contents
Dash Disassembly
–Honda Accord 2003-2007............................................................................................3-4
Kit Assembly
–DIN radio provision ..........................................................................................................5
–ISO radio provision...........................................................................................................6
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recommends MECP
certified technicians
99-7864

1. Unsnap and remove shift lever trim ring.
(Figure A)
2. Unsnap coin tray/ashtray from assembly
and remove. Rubber cover may come
out first but entire assembly must be
removed to access screws below.
(Figure B)
3. Remove (2) Phillips screws from under
coin tray/ashtray and remove entire
assembly. (Figure C)
Continued on next page
3
Honda Accord 2003-2007
Dash Disassembly 99-7864
R
N
D
D
(Figure A)
R
N
D
D
(Figure C)
R
N
D
D
(Figure B)

4
Dash Disassembly 99-7864
Honda Accord 2003-2007
4. Remove (2) Phillips screws from bottom
of pocket assembly and unsnap and
remove. (Figure D)
5. Remove (2) Phillips screws facing up
under radio/climate control assembly.)
(Figure E)
6. Push and hold the hazard button down.
Carefully insert a flat blade screwdriver
into the slot below the button and push
down to release the center clip.
(Figure F)
7. Unsnap and remove upper panel
(including a/c vents) and remove (3)
Phillips screws behind the panel.
(Figure G)
Tip: You can use a hook tool to grasp
the panel inside of the vent and pull
toward the rear of the vehicle. Be
careful not to scratch the panel.
8. Unclip and remove radio/climate
control assembly.
Continue to kit assembly
(Figure E)
(Figure G)
(Figure F)
R
P
N
D
D
(Figure D)

5
Kit Assembly 99-7864
1. Snap the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure A)
2. Slide the aftermarket radio into the cage
and secure. (Figure B)
3. Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adapter from Metra or
AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
4. Reassemble dash in reverse order
of disassembly.
Note: The orange wire coming out of
the back of the 99-7864 needs to be
connected to the orange illumination
wire coming from the Metra 70-1721
wire harness (sold separately).
DIN radio provision
(Figure A)
(Figure B)
Programming:
In order to adjust the 99-7864 to the
different types of radios available in the
Honda Accord, the 99-7864 has a
program feature.
4 Door Sedans ONLY:
To program the kit you will need to start
your vehicle then hold the A/C button for
approximately 5 seconds or until the light
starts to blink. The climate controls will be
programmed when the light stops blinking.
2 Door Coupes ONLY:
To program the kit you will need to start
your vehicle then hold the Rear Defrost
button for approximately 5 seconds or
until the light starts to blink. The climate
controls will be programmed when the
light stops blinking.

6
Kit Assembly 99-7864
1. Mount the ISO Brackets to the head unit
with the screws supplied with the unit.
(Figure A)
2. Slide the head unit into the radio
opening until the side clips engage.
Snap the Trim plate into the Radio
Housing. (Figure B)
3. Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adapter from Metra or
AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
4. Reassemble dash in reverse order
of disassembly.
Note: The orange wire coming out of
the back of the 99-7864 needs to be
connected to the orange illumination
wire coming from the Metra 70-1721
wire harness (sold separately).
ISO radio provision
(Figure A)
(Figure B)
Programming:
In order to adjust the 99-7864 to the
different types of radios available in the
Honda Accord, the 99-7864 has a
program feature.
4 Door Sedans ONLY:
To program the kit you will need to start
your vehicle then hold the A/C button for
approximately 5 seconds or until the light
starts to blink. The climate controls will be
programmed when the light stops blinking.
2 Door Coupes ONLY:
To program the kit you will need to start
your vehicle then hold the Rear Defrost
button for approximately 5 seconds or
until the light starts to blink. The climate
controls will be programmed when the
light stops blinking.

Notes

METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
1-800-221-0932 metraonline.com
INSTALLATION INSTRUCTIONS FOR PART 99-7864
REV. 11/20/17

METRA. THE WORLD’S BEST KITS.™
© COPYRIGHT 2004-2011 METRA ELECTRONICS CORPORATION
APLICACIONES
1-800-221-0932 metraonline.com
INSTRUCCIONES DE INSTALACIÓN PARA LA PIEZA 99-7864
REV. 11/20/17
• Destornillador cabeza plana • Herramienta de remoción de panel • Destornillador Phillips
HERRAMIENTAS REQUERIDAS
Honda Accord 2003-2007
99-7864
(Equipado con controles de clima de zona única)
• A) Carcasa de radio/control de clima • B) Soportes ISO • C) Placa de moldura ISO • D) Tornillos PPH-1034
CARACTERÍSTICAS DEL KIT
COMPONENTES DEL KIT
B CA
• Provisión de radio DIN
• Provisión de radio ISO
CABLEADO Y CONEXIONES DE ANTENA (se venden por separado)
Arnés de cableado:
• 70-1721 - Arnés Honda/Acura 1998
• 70-7864DZ - Arnés Accord de doble zona eliminatoria 2003-2007
Adaptador de antena:
• No se requiere
D
U.S. PATENT # D519,995

Indice
Desmontaje del tablero
–Honda Accord 2003-2007............................................................................................3-4
Ensamble del kit
–Provisión de radio DIN......................................................................................................5
–Provisión de radio ISO......................................................................................................6
99-7864
PRECAUCIÓN: Metra recomienda desconectar el terminal negativo de la batería antes de
comenzar cualquier instalación. Todos los accesorios, interruptores y, especialmente, las luces
indicadoras de airbag deben estar enchufados antes de volver a conectar la batería o comenzar
el ciclo de ignición.
Nota: Remítase a las instrucciones incluidas con el radio de posventa.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
Metra recomienda técnicos con
certificación del Programa de
Certificación en Electrónica Móvil
(Mobile Electronics Certification
Program, MECP).
EL CONOCIMIENTO ES PODER
Mejore sus habilidades de instalación y fabricación
inscribiéndose en la escuela de dispositivos
electrónicos móviles más reconocida y respetada de
nuestra industria. Regístrese en www.installerinstitute.
com o llame al 800-354-6782 para obtener más
información y avance hacia un futuro mejor.