Metra Electronics 99-9014HG User manual

Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 10/10/19 INST99-9014HG
INSTALLATION INSTRUCTIONS
99-9014HG
Attention! Let the vehicle sit with the key
out of the ignition for a few minutes before
removing the factory radio. When testing the
aftermarket equipment, ensure that all factory
equipment is connected before cycling the
key to ignition.
KIT FEATURES
• ISO DIN radio provision
• ISO DDIN radio provision †
• Pioneer modular DDIN radio provision †
• Painted high gloss black to match the factory finish
KIT COMPONENTS
• A) Radio trim panel • B) Radio brackets • C) Support bracket • D) Blank panel • E) #4 x 3/8” Phillips pan-head screws (6)
• F) #8 x 3/8” Phillips truss-head screws (2) • G) #8 x 1/2” Phillips truss-head screws (4) • H) Panel clips (2) • I) Panel clip mounts (2) TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• Cutting tool • T-20 Torx driver
• VW radio removal tool (Metra part #86-9001)
TABLE OF CONTENTS
Dash Disassembly ...............................................2-3
Kit Preparation .......................................................4
Kit Assembly
–ISO DIN radio provision .......................................5
–ISO DDIN radio provision .....................................6
–Pioneer modular DDIN radio provision .............7
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness: AXTC-VW2
Antenna Adapter: 40-EU56-36
A B
F G
C D E
Volkswagen Jetta 2019-Up
H I
Visit MetraOnline.com for more detailed information about the product and up-to-date vehicle
specific applications
† Only for with ISO DDIN radios which have an “L” shaped chassis design, with the radio chassis at the
top of the screen. At present only the Sony XAV-AX100, XAV-AX200, and XAV-AX5000 radios have this
design. The Pioneer modular radios, DMH-C2550NEX and DMH-C2500NEX, can also be used.

1.800.221.0932
|
MetraOnline.com
2
1. Open the driver’s door, then unclip
and remove the dashboard side panel.
(Figure A)
2. Unclip and remove the trim panel
directly below the far left a/c vent.
Remove (1) T-20 Torx screw exposed.
(Figure B)
3. Unclip and remove the trim panel to the
left of the steering column. (Figure C)
4. Unclip and remove the trim panel
directly below the far right a/c vent.
Remove (2) T-20 Torx screws exposed.
(Figure D)
5. Unclip and remove the far right a/c vent.
(Figure E)
Continued on the next page
(Figure E)
(Figure D)
DASH DISASSEMBLY
(Figure A)
(Figure B)
(Figure C)

REV. 10/10/2019 INST99-9014HG 3
DASH DISASSEMBLY (CONT.)
6. Unclip and remove the trim panel above
the glove box. Remove (3) T-20 Torx
screws exposed, securing the radio &
instrument trim panel. (Figure F,G)
7. Unclip the top of the steering column
shroud. The shroud is connected to the
radio & instrument-cluster trim panel by
a piece of material and will be removed
fully in the following step. (Figure H)
8. Unclip and remove the radio &
instrument-cluster trim panel, including
the shroud loosened in the prior step.
(Figure I)
9. Using radio removal keys (sold
separately), release the radio. Slide the
radio out, then unplug and remove.
Remove (2) metal clips attached to
the sides of the radio for re-use in Kit
Preparation. (Figure J)
Note: This is just the display for the
radio. The radio brain is located above
the glove-box.
Continue to Kit Preparation
(Figure F)
(Figure G)
(Figure H)
(Figure I)
(Figure J)
Use this end of the
radio removal key

1.800.221.0932
|
MetraOnline.com
4
KIT PREPARATION
(Figure E)
(Figure D)
1. Attach the factory metal clips removed
in Dash Disassembly to the radio trim
panel. (Figure A)
2. For base model Jetta:
Remove (5) Torx T-20 screws, then
remove the radio support bracket.
(Figure B)
3. Secure the support bracket to the
vehicle using (2) #8 x 1/2” Phillips truss-
head screws provided. (Figure C)
4. Secure the panel clip mounts to the
radio trim panel using (4) #4 x 3/8”
Phillips pan-head screws provided.
(Figure D)
5. Attach the (2) panel clips provided to
the panel clip mounts. (Figure E)
Continue to Kit Assembly
(Figure A)
(Figure B)
(Figure C)

REV. 10/10/2019 INST99-9014HG 5
(Figure A) (Figure C)
(Figure B)
KIT ASSEMBLY
ISO DIN radio provision
1. Remove the metal DIN sleeve and trim
ring from the aftermarket radio.
2. Cut the radio brackets at the scored line.
(Figure A)
3. Secure the radio brackets to the radio
using screws supplied with the radio.
(Figure B)
4. Locate the factory wiring harness and
antenna connector at the radio location
above the glove-box. Complete all
necessary connections to the radio.
Metra recommends using the proper
mating adapter from Metra and/
or Axxess. Test the radio for proper
operation.
5. Slide the radio assembly into the dash,
then secure using (2) #8 x 1/2” Phillips
truss-head screws up top, and (2) #8 x
3/8” Phillips truss-head down below.
6. Secure the blank panel to the radio
trim panel using (2) #4 x 3/8” Phillips
pan-head screws provided. (Figure C)
7. Clip the radio trim panel onto the radio
assembly.
8. Reassemble the dash in reverse
order of disassembly to complete the
installation.
Remove sheded area

1.800.221.0932
|
MetraOnline.com
6
(Figure A) (Figure B)
KIT ASSEMBLY
ISO DDIN radio provision
1. Cut the radio brackets at the scored line.
(Figure A)
2. Secure the radio brackets to the radio
using screws supplied with the radio.
(Figure B)
3. Locate the factory wiring harness and
antenna connector at the radio location
above the glove-box. Complete all
necessary connections to the radio.
Metra recommends using the proper
mating adapter from Metra and/
or Axxess. Test the radio for proper
operation.
4. Slide the radio assembly into the dash,
then secure using (2) #8 x 1/2” Phillips
truss-head screws up top, and (2) #8 x
3/8” Phillips truss-head down below.
5. Clip the radio trim panel onto the
radio assembly.
6. Reassemble the dash in reverse
order of disassembly to complete the
installation.
Remove shaded area

REV. 10/10/2019 INST99-9014HG 7
Pioneer Modular DDIN radio provision
Note: For steps 1 and 2, reference the
installation manual provided with the radio
for which hardware to use. The display
screen and radio chassis use two different
types of screws.
1. Secure the Pioneer radio display to the
radio brackets using (4) screws supplied
with the radio. (Figure A)
2. Slide the Pioneer radio chassis between
the radio brackets, then secure using (4)
screws supplied with the radio.
(Figure B)
3. Locate the factory wiring harness and
antenna connector at the radio location
above the glove-box. Complete all
necessary connections to the radio.
Metra recommends using the proper
mating adapter from Metra and/
or Axxess. Test the radio for proper
operation.
4. Slide the Pioneer radio assembly into
the dash, then secure using (2) #8 x 1/2”
Phillips truss-head screws up top, and
(2) #8 x 3/8” Phillips truss-head down
below.
5. Clip the radio trim panel to the Pioneer
radio assembly.
6. Reassemble the dash in reverse
order of disassembly to complete the
installation.
(Figure A) (Figure B)
KIT ASSEMBLY

KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics school in our industry.
Log onto www.installerinstitute.com or call
800-354-6782 for more information and take steps
toward a better tomorrow.
®
Metra recommends MECP
certified technicians
Metra. The World’s Best Kits.®MetraOnline.com © COPYRIGHT 2019 METRA ELECTRONICS CORPORATION REV. 10/10/19 INST99-9014HG
INSTALLATION INSTRUCTIONS
99-9014HG
If you are having difficulties with the installation
of this product, contact our Tech Support line
either by phone at 386-257-1187, or email at
[e-mail]. Before
doing so, look over the instruction booklet a
second time and ensure that the installation was
performed exactly as the instruction booklet
is stated. Have the vehicle apart and ready to
perform troubleshooting steps before contacting
Metra/Axxess Tech Support.