Metra Electronics 99-3413 User manual

2-SHAFT HEAD UNITS: Slide the aftermarket head unit into the kit and secure with shaft
nuts. (see Fig. A)
DIN HEAD UNITS: Cut and remove the shaft supports. Slide the DIN cage into the Radio
Housing and secure by bending the metal locking tabs down. Slide the aftermarket head unit
into the cage until secure. (see Fig. B)
(If an equalizer will be included, slide the unit into the back of the Radio Housing and secure.
If an equalizer will NOT be included, snap the Equalizer Dummy Plate into the opening).
ALL VEHICLES
6 7
5
Locate the factory wiring harness in the
dash. Metra recommends using the
proper mating adaptor and making
connections as shown. (Isolate and
individually tape off the ends of any
unused wires to prevent electrical short
circuit).
COROLLA: Re-connect the battery terminal and
test the unit for proper operation. Mount the head
unit/kit assembly to the sub-dash with (4) Phillips
screws previously removed in step #1.
PRIZM: Re-connect the battery terminal and test
the unit for proper operation. Mount the head
unit/kit assembly to the sub-dash with (2) Phillips
screws previously removed in step #1 ("A") and
(2) Phillips Screws supplied ("B").
A
B
C
D
A) Strip wire ends back ½"
B) Twist ends together
C) Solder
D) Tape
3
99-3413
INSTALLATION
INSTRUCTIONS
APPLICATIONS
CAR PAGE
CHEVROLET
Prizm 1998-2003.........................................................1
TOYOTA
Corolla 1998-2002.....................................................2
KIT COMPONENTS
TOOLS REQUIRED
Cutting tool
Wrench
Phillips screwdriver
Prizm
Spacers
Equalizer
Dummy Plate
(2) Phillips
Screws
Fig. B
"B"
"A"
"A"
"B"
Fig. A
KIT FEATURES
Shaft and
DIN unit
provisions
Cupholder
provisions
Equalizer
provisions
Radio Housing
1-800-221-0932 www.metraonline.com
© COPYRIGHT 2001-07 METRA ELECTRONICS CORPORATION
rev. 06-13-07

Disconnect the negative battery terminal to
prevent an accidental short circuit. Remove
the ashtray. Unclip the radio trim bezel and
disconnect the wiring. Remove (4) Phillips
screws se c u r i n g the factory he a d
unit/cupholder assembly, slide the assembly
out and disconnect the wiring.
Disconnect the negative battery terminal to
prevent an accidental short circuit. Unclip
the radio trim bezel (upper dash). Remove
(4) Phillips screws from the factory head
unit, slide the unit out and disconnect the
wiring. Remove the ashtray and unclip the
trim bezel (lower dash). Remove (4) Phillips
screws from the factory pocket/cupholder
assembly and remove the assembly. (Metra
recommends ordering the 88-00-8000 or
88-00-9000 to fill the space left in the upper
dash location).
Locate the faceplate supplied with the
aftermarket head unit. Place the faceplate
into the recessed opening in the Radio
Housing. If the faceplate fits easily into the
opening with no interference, leave the
Housing intact. If the faceplate does NOT fit
easily into the opening, trim away the ribs
located on the top and bottom of the opening
("A").
Locate the faceplate supplied with the
aftermarket head unit. Place the faceplate
into the recessed opening in the Radio
Housing. If the faceplate fits easily into the
opening with no interference, leave the
Housing intact. If the faceplate does NOT fit
easily into the opening, trim away the ribs
located on the top and bottom of the opening
("A").
Convert the Radio Housing by cutting and
removing the pins located under the
equalizer opening ("A"). Trim no less than
1/8" and no more than 1/4" from the bottom
of each upper mounting tab ("B"). Snap the
Prizm Spacers onto the back of the lower
mounting tabs ("C").
Remove the cupholder from the factory head
unit assembly. Slide the cupholder into the
bottom of the Radio Housing until the
locating pins engage the slots in the kit.
(Once the locating pins are engaged, PUSH
the cupholder into the Housing until it stops).
Skip to the Installation Instruction for ALL
VEHICLES on Page #3.
Remove the cupholder from the factory head
unit assembly. Slide the cupholder into the
bottom of the Radio Housing until the
locating pins engage the slots in the kit.
(Once the locating pins are engaged,
maneuver the cupholder until it is flush with
the face of the Housing). Skip to the
Installation Instruction for ALL VEHICLES on
Page #3.
CHEVROLET Prizm 1998-2003 TOYOTA Corolla 1998-2002
1 1
44
2 2
3
12
Locate the v-cut along the top lip of the
Radio Housing. Using the v-cut as a guide,
cut and remove the top portion of the
Housing as indicated above.
3
"A"
"A"
"C"
"A"
"B"
"C"