Metra Electronics 99-9011 User manual

INSTALLATION INSTRUCTIONS FOR PART 99-9011
1-800-221-0932 www.metraonline.com
KIT FEATURES
©COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
•DIN Head Unit Provision with pocket
•ISO Head Unit Provision with pocket
•Double DIN Head Unit Provision
•ISO Stacked Head Unit Provision
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) DDIN Brackets • E) DDIN Trim Plate • F) Pocket
KIT COMPONENTS
99-9011
A
B
VW
CC 2009/EOS 2007-09/New Jetta 2005-09
GLI 2008-09/GTI 2006-09/Passat 2006-09
Rabbit 2006-09/R32 2008-09/Tiguan 2009
F
E
C
D
Applications
T-20 Torx Screwdriver • Flat Blade Screwdriver Or Panel Removal Tool
TOOLS REQUIRED:
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wireharness:
•XSVI-9003-NAV VW Interface 2003-up
Antenna adapter:
•40-EU55-adapter for amplified antenna 2002-up

TABLE OF CONTENTS
99-9011
• Dash Disassembly
-GLI 2008 -09................................................................................1,2
-GTI 2006-09.................................................................................1,2
-New Jetta 2005-09......................................................................1,2
-Rabbit 2006-09............................................................................1,2
-R32 2008-09................................................................................1,2
- CC 2009 ........................................................................................ 3
-Passat 2006-09 ............................................................................ 3
-Tiguan 2009................................................................................... 4
-Eos 2007-09................................................................................... 5
• Kit Assembly:
-DIN Head Unit Provision with Pocket ............................................6
-ISO Head Unit Provision with Pocket .............................................7
-Double DIN Head Unit Provision.....................................................8
-Stacked ISO Head Unit Provision ...................................................9
• Final Assembly .............................................................................10
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake
steps towardabetter tomorrow.

1
99-9011 DASH DISASSEMBLY
A
B
C
D
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip and remove the grille from
the top-center of dash. (Figure A)
2
Remove one T-20 torx screw from
black insert from under grille
removed in step one.
(Figure B)
3
Remove insert. (Figure C)
4
Remove two T-20 torx screws from
under blackinsert removed in step
two.
(Figure D)
5
NEW JETTA2005-09/GLI 2008-09
GTI 2006-09/RABBIT 2006-09
R32 2008-09

2
99-9011 DASH DISASSEMBLY
E
F
G
H
Unsnap and remove the vent
assembly above the radio.
(Figure E)
6
Remove two T-20 torx screws from
top sides of radio/climate panel.
(Figure F)
7
Remove four T-20 torx screws to
remove the radio. (Figure H)
9
Remove panel. (Figure G)
8
NEW JETTA2005-09/GLI 2008-09
GTI 2006-08-09/RABBIT 2006-09
R32 2008-09

3
99-9011 DASH DISASSEMBLY
Remove (4) T-20 Torx screws to
remove radio.
3
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip and remove trim panel sur-
rounding radio. (Figure A)
2
PASSENGER AIRBAG OFF
ON
VOL
SCAN
TUNE
BASSTREBBALFAD
FMAM
CD
AC
FM2
103.7MHZ
72
64 80
1
2
3
4
CC 2009 / VW PASSAT 2006-2009
A

4
99-9011 DASH DISASSEMBLY
AF
PASSENGER
AIR BAG
PASSENGER
AIR BAG
PASSENGER
AIR BAG
A
AF
PASSENGER
AIR BAG
B
AF
PASSENGER
AIR BAG
C
AF
D
TIGUAN 2009
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip and remove passenger air
bag light panel to the right of the
hazard light button.
(Figure A)
2
Remove (2) T-20 Torx screws
exposed behind the two panels
removed in the twoprevious steps.
(Figure B)
4
Unclip and remove the trim panel
surrounding the radio. (Figure C)
5
Remove (4) T-20 Torx screws secur-
ing the radio. Unplug and remove
the radio.
(Figure D)
6
Unclip and remove the panel with
the two slots in it to the left of the
hazard light button.
(Figure A)
3

5
99-9011 DASH DISASSEMBLY
A
B
EOS 2007-2009
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Unclip and remove the radio trim
panel. (Figure A)
2
Remove the (4) screws securing the
radio. Unplug and remove the radio.
(Figure B)
3

6
99-9011 KIT ASSEMBLY
Snap the pocket into the radio hous-
ing.
(Figure C)
3
Slide the DIN cage into the Radio
Housing and secure by bending
the metal locking tabs down.
(Figure A)
1
Slide the aftermarket head unit
into the cage and secure.
(Figure B)
2
DIN HEAD UNIT PROVISION WITH POCKET
A
B
C

7
99-9011 KIT ASSEMBLY
Snap the pocket into the radio hous-
ing.
(Figure C)
4
Slide the head unit into the radio
opening until the side clips
engage. (Figure B)
2
Snap the ISO Trim Plate into the
Radio Housing.
(FigureC)
3
ISO HEAD UNIT PROVISION WITH POCKET
A
B
C
Mount the ISO Brackets to the
head unit with the screws sup-
plied with the unit.
(Figure A)
1

8
99-9011 KIT ASSEMBLY
Slide the DDIN radio unit into the
DDIN bracket/radio housing assem-
bly and secure the unit to the kit
using the screws supplied with the
head unit.
(Figure C)
3
Cut and remove center divide from
radio housing.
(Figure A)
1
Snap the DDIN trim-plate onto the
housing/radio assembly.
(FigureC)
4
Snap the DDIN brackets to the
inside edge of the radio housing.
(Figure B)
2
DOUBLE DIN HEAD UNIT PROVISION
A
B
C

9
99-9011 KIT ASSEMBLY
Snap the DDIN trim-plate onto the
housing/radio assembly.
(Figure C)
4
Snap the DDIN brackets to the
inside edge of the radio housing.
(Figure B)
2
Slide the stacked ISO DIN units into
the DDIN bracket/radio housing
assembly and secure the units to the
kit using the screws supplied with
the head units.
(Figure C)
3
STACKED ISO HEAD UNIT PROVISION
A
C
B
Cut and remove center divider
from radio housing. (Figure A)
1

10
FINAL ASSEMBLY
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
FINAL WIRING CONNECTIONS
99-9011
FINAL ASSEMBLY
12V Ignition / Acc . . . Red
12V Batt / Memory . . Yellow
Ground . . . . . . . . . . . Black*
Power Antenna . . . . . Blue
Amp Turn-On . . . . . . Blue / White
Amp Ground . . . . . . . Black / White
Illumination. . . . . . . . Orange
Dimmer ..........Orange / White
Right Front (+) . . . . . Gray
Right Front (-). . . . . . Gray/ Black
Left Front (+) . . . . . . White
Left Front (-) . . . . . . . White / Black
Right Rear (+). . . . . . Violet
Right Rear (-) . . . . . . Violet / Black
Left Rear (+). . . . . . . Green
Left Rear (-) . . . . . . . Green / Black
METRA / EIA WIRING CODE
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
1
Locate the factorywiring harness in the dash. Metrarecommends using the
proper mating adapter and making connections as shown. (Isolate and individually
tape off the ends of any unused wires to prevent electrical short circuit.)
2
Re-connect the negative battery terminal and test the unit for proper operation.
3
Reassemble in reverse order of disassembly.
A
A) Strip wire ends back 1/2"
B) Twist ends together
C) Solder
D) Tape
B
C
D
1-800-221-0932
REV.05/26/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION INST99-9011
www.metraonline.com