Metra Electronics 99-8903B User manual

INSTALLATION INSTRUCTIONS FOR PART 99-8903B
APPLICATIONS
SUBARU
LEGACY & OUTBACK
2010
(FOR NON-NAVIGATION RADIOS ONLY)
KIT FEATURES
•DIN radio provision with pocket
•ISO radio provision with pocket
•Painted scratch resistant matte black
A) Radio Housing B) ISO Brackets C) Trim plate
KIT COMPONENTS
A
TOOLS REQUIRED:
•Small Flat Blade Screwdriver • Phillips Screwdriver
•Panel Removal Tool • Socket Wrench
1-800-221-0932
©COPYRIGHT 2007-2009 METRA ELECTRONICS CORPORATION
www.metraonline.com
99-8903B
BC
METRA. THE WORLD’S BEST KITS.™
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Wiring Harness:
•70-8901 Subaru Harness 1990-Up
•70-7552 Nissan Harness 2007-Up
Antenna Adapter:
•40-SB10 Subaru Antenna Adapter 2005-Up

Dash Disassembly
-2010 Subaru Legacy . . . . . . . . . . . .......................... 1
-2010 Subaru Outback . . . . . . . . . . .......................... 1
Kit Assembly
-DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
-ISO DIN Head Unit Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
TABLE OF CONTENTS
99-8903B
*Note:
Refer also to the instructions included with the aftermarket radio.
K NOWLEDGE IS P OWER
Enhanceyour installation and fabrication skillsby
enrolling in the most recognizedandrespected
mobile electronics school in our industry.
Log onto www.installerinstitute.comor call
800-354-6782 for more informationandtake steps
toward abetter tomorrow.
Metra recommends MECP certified
technicians.

99-8903B DASH DISASSEMBLY
2010 SUBARU LEGACY / OUTBACK
A
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
1
Unclip and remove the radio trim
panel including the a/c vents.
( Figure A)
2
Remove (4) Phillips screws securing
the factory radio.
3

99-8903B KIT ASSEMBLY
A
B
2
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
1
Slide the DIN cage into the Radio
Housing and securebybending the
metal locking tabs down. (Figure A)
2
Slide the aftermarket head unit into
the cage and secure. (Figure B)
3
Reassemble dash in reverse order of
disassembly.
4
2010 SUBARU LEGACY / OUTBACK
DIN HEAD UNIT PROVISION

99-8903B KIT ASSEMBLY
A
B
3
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
1
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure A)
2
Slide the head unit into the radio
opening until the side clips engage.
(Figure B)
3
Snap the Trim plate into the Radio
Housing.(FigureB)
4
Reassemble dash in reverse order of
disassembly.
5
2010 SUBARU LEGACY / OUTBACK
ISO DIN HEAD UNIT PROVISION

NOTES
99-8903B

NOTES
99-8903B

306
INSTRUCTIONS
1-800-221-0932
REV. 12/21/09 © COPYRIGHT 2003-2009 METRA ELECTRONICS CORPORATION INST99-8903B
www.metraonline.com
99-8903B INSTRUCTIONS
METRA. THE WORLD’S BEST KITS.™