Microsens MS453510M User manual

4 10/100/1000TX plus 1 MINI GBIC
Web Managed Switch
User Manual
MS453510M

CE Mark Warning
This is a Class-A product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures.

Content
CE Mark Warning.................................................................................................2
INTRODUCTION............................................................................... 1
Features...............................................................................................................1
Software Feature..................................................................................................2
Package Contents................................................................................................3
HARDWARE DESCRIPTION............................................................ 4
Physical dimension ..............................................................................................4
Front Panel...........................................................................................................4
Rear Panel...........................................................................................................5
LED Indicators......................................................................................................5
Desktop Installation..............................................................................................7
Attaching Rubber Feet..................................................................................7
Power On.............................................................................................................7
NETWORK APPLICATION............................................................... 8
Small Workgroup..................................................................................................8
Segment Bridge ...................................................................................................8
WEB-BASED MANAGEMENT ....................................................... 10
About Web-based Management.........................................................................10
System Login .....................................................................................................10
System Configuration.........................................................................................11
Port Configuration ..............................................................................................13
Statistics-1 (Overview) .......................................................................................14
Statistics-2 (Detailed).........................................................................................15
VLAN Setting......................................................................................................15
VLAN Port Setting.......................................................................................16
Port Trunk ..........................................................................................................17
LACP Setting......................................................................................................18
LACP Status.......................................................................................................19

Spanning Tree...................................................................................................20
RSTP System Configuration....................................................................... 20
RSTP Port Configuration............................................................................22
Spanning Tree Status........................................................................................22
802.1X Configuration.........................................................................................23
Parameters Configuration........................................................................... 24
QoS Setting ....................................................................................................... 25
System Restart.................................................................................................. 28
Factory Default .................................................................................................. 28
Firmware Upload ............................................................................................... 28
Configuration Upload/Download........................................................................29
TROUBLESHOOTING ....................................................................31
Incorrect connections......................................................................................... 31
Faulty or loose cables ......................................................................... 31
Non-standard cables ........................................................................... 31
Improper Network Topologies ............................................................. 32
Diagnosing LED Indicators................................................................................ 32
TECHNICAL SPECIFICATION ....................................................... 33
APPENDIX ......................................................................................36
10 /100BASE-TX Pin outs ................................................................................. 36
10/100Base-TX Cable Schematic...................................................................... 36
10/100/1000Base-TX Pin outs...........................................................................37
10/100/1000Base-TX Cable Schematic............................................................. 38

1
Introduction
The 4 10/100/1000T plus 1 Mini-GBIC Web Managed Switch is a multi-port
Switch that can be used to build high-performance switched workgroup networks.
The Switch is targeted at workgroup or department.
The 4 10/100/1000T plus 1 Mini-GBIC Web Managed Switch features a
“store-and-forward “ switching scheme that offers low latency for high-speed
networking and allows the switch to auto-learn and store source address in a
8K-entry MAC address table.
The 4 10/100/1000T plus 1 Mini-GBIC Web Managed Switch has 4 auto-sensing
10/100/1000 Base-TX RJ-45 ports plus one MINI GBIC slot that enables
extended distance connection.
Features
Conforms to IEEE 802.3, 802.3u, 802.3ab, 802.3x and 802.1x
Store-and-Forward switching architecture
Web Management
Auto-MDIX on all ports
10Gbps back-plane
N-Way Auto-Negotiation
Supports Port Based VLAN
Supports Class of Service
Supports STP (Spanning Tree Protocol)
Supports Port Trunk
Back pressure with half duplex (10/100Mbps)
Flow control with full duplex (10/100/1000Mbps)
Web Firmware upgrade

2
8K MAC address table
112Kbytes memory buffer
True non-blocking switching
8K Jumbo Frame supported
Software Feature
Management Web Management
Firmware update Web UI firmware update
System default
One default button for system default
Default IP: 192.168.16.1
Gateway: 192.168.16.254
Subnet Mask: 255.255.255.0
Port Trunk
IEEE802.3ad port trunk with link aggregation
control protocol (LACP)
The trunk group up to 2 and maximum trunk port
member up to 2 ports.
VLAN
Port Based VLAN
VLAN ID up to 5
VLAN group up to 5
DHCP DHCP client feature
Quality of Service
Port based
Tag based
IPv4 ToS
Class of Service Per port supports 4 priority queues

3
Spanning Tree IEEE802.1w rapid spanning tree and compatible
with IEEE 802.1d
Package Contents
Unpack the contents of the 4 10/100/1000T plus 1 Mini-GBIC Web Managed
Switch and verify them against the checklist below:
4 10/100/1000T plus 1 Mini-GBIC Web Managed Switch
DC Power Cord
Four Rubber Pads
User Manual
4 10/100/1000 plus 1 Mini-GBIC Four Rubber Pads
Web Managed Switch
DC Power Adapter User Manual
Package Contents
Compare the contents of your 4 10/100/1000T plus 1 Mini-GBIC Web Managed
Switch package with the standard checklist above. If any item is missing or
damaged, please contact your local dealer for exchanging.

4
Hardware Description
This section mainly describes the hardware of the 4 10/100/1000T plus 1
Mini-GBIC Web Managed Switch, and gives a physical and functional overview
on certain switch.
Physical dimension
The 4 10/100/1000T plus 1 Mini-GBIC Web Managed Switch physical dimension
is 165 x 100 x 32.5 mm (W x D x H).
Front Panel
The Front Panel of the 4 10/100/1000T plus 1 Mini-GBIC Web Managed Switch
consists of LED Indicators and a reset button. Please refer to LED Indicator
section for LED description.
Reset button: It provides an easy way for user to reset the configuration
back to the default settings. Press the button more than 5 seconds, and then
the switch will restart and set all configurations back to the default settings.

5
Rear Panel
The rear panel consists of the 4 10/100/1000Base-TX RJ-45 port, one Mini GBIC
slot, and DC Power Jack as shown in the figure below. The switch will work with
DC in the range of 12V/0.8A.
The Rear Panel of 4 10/100/1000T plus 1 Mini-GBIC Web Managed Switch
RJ-45 Ports (Auto MDI/MDIX): 4x 10/100/1000 N-way auto-sensing for
10Base-T, 100Base-TX or 1000Base-T connections.
In general, MDI means connecting to another Hub or Switch while MDIX
means connecting to a workstation or PC. Therefore, Auto MDI/MDIX
would allow connecting to another Switch or workstation without changing
non-crossover or crossover cabling.
Mini GBIC slot: The appropriate replaceable Mini-GBIC port is available
with a variety of different transmitter and receiver types, allowing users to
select the appropriate transceiver for each link to provide the required
optical reach over the available optical fiber type.There is one LED
indicator—LNK/ACT—for Mini-GBIC port on the front panel.
LED Indicators
The LED Indicators display the real-time information of systematic operation
status. Please see definition of the LED indicators as follows.

6
LED Status Color Description
Power
On Green Power On
Off --
No Power inputs or Power cord
disconnected
100/1000
On Green
The port is operating at the speed of
1000Mbps.
On Yellow
The port is operation at the speed of
100Mbps.
Off --
In 10Mbps mode or no device
attached
LNK /ACT
On Green
The port is well connected with the
device.
Blinks Green
The port is in processing of receiving
or transmitting data.
Off -- No device attached.
FDX /COL
On Yellow
The port is operating in Full-duplex
mode.
Blinks Yellow
Collision of Packets occurs in the
port.
Off --
Half-duplex mode or no device
attached.
LNK /ACT
(MINI GBIC)
On Green
The port is well connected with the
device.
Blinks Green The port is in processing of
receiving
or transmitting data.
Off -- No data transmitted or no device
connected
The Definition of LED Indicators

7
Desktop Installation
Set the switch on a sufficiently large flat space with a power outlet nearby. The
surface where you put the switch should be clean, smooth, level and sturdy.
Make sure there is enough clearance around the switch to allow attachment of
cables, power cord and allow air circulation.
Attaching Rubber Feet
A. Make sure mounting surface on the bottom of the switch is grease and dust
free.
B. Remove adhesive backing from your Rubber Pads.
C. Apply the Rubber Feet to each corner on the bottom of the switch. These
footpads can prevent the switch from shock/vibration.
Power On
Connect the power adaptor to the power jack on the rear panel of the switch. The
other side of power adaptor is connected to the power outlet. The external power
supply in the switch works with DC power in 12V/0.8A. Please check with the
power indicator on the front panel to see if power is properly supplied.

8
Network Application
This section provides user a few samples of network topology in witch the switch
is used. In general, the 4 10/100/1000T plus 1 Mini-GBIC Web Managed Switch
is designed as a segment switch. That is, with its address table (8000 MAC
address) and high performance, it is ideal for interconnecting networking
segments.
PC, workstations, and servers can communicate each other by directly
connecting with 4 10/100/1000T plus 1 Mini-GBIC Web Managed Switch. The
switch automatically learns nodes address, which are subsequently used to filter
and forward all traffic based on the destination address.
By using Uplink port, the switch can connect with another switch or hub to
interconnect other small-switched workgroups to form a larger switched network.
Meanwhile, you can also use fiber ports to connect switches. The distance
between two switches via fiber cable depends on the type of fiber transceiver.
Small Workgroup
The 4 10/100/1000T plus 1 Mini-GBIC Web Managed Switch can be used as a
standalone switch to which personal computers, server, printer server, are
directly connected to form small workgroup.
Segment Bridge
For enterprise networks where large data broadcasts are constantly processed,
this switch is an ideal solution for department users to connect to the corporate
backbone.

9
Two 4 10/100/1000T + 1 Mini-GBIC Web Managed Switches with PCs, print
server, and local server attached, are both connected to the core switch. All the
devices in this network can communicate with each other through the 4
10/100/1000T plus 1 Mini-GBIC Web Managed Switch. Connecting servers to the
4 10/100/1000T plus 1 Mini-GBIC Web Managed Switch allows users accessing
the data on server. By using fiber ports to connect switches, the distance
between two switches depends on the type of fiber transceiver.

10
Web-Based Management
This section introduces the function of the 4 10/100/1000T plus 1 Mini-GBIC Web
Managed Switch configuration.
About Web-based Management
On the CPU board of the switch there is an embedded HTML web site residing in
flash memory, which offers advanced management features and allow users to
manage the switch from anywhere on the network through a standard browser
such as Microsoft Internet Explorer.
The Web-Based Management supports Internet Explorer 6.0. And, it is applied
with Java Applets for reducing network bandwidth consumption, enhance access
speed and present an easy viewing screen.
System Login
The default value list as below:
IP Address: 192.168.16.1
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.16.254
Password: root
1. Launch the Internet Explorer.
2. Key in “http://” + “IP Address” of the 4 10/100/1000T plus 1 Mini-GBIC Web
Managed Switch, and then press “Enter”.
3. Login screen will appear right after.

11
4. Key in the default password as “root”.
5. Click
Apply
, and then configuration is ready to be set up.
Main Interface
System Configuration
Displays system parameters information listed as below, and the other
parameters of system can be configured as well.
MAC Address: Displays the unique hardware address assigned by
manufacturer (default).
S/W Version: Displays the Software Version of Kernel.
H/W Version: Displays the Hardware Version of the switch.
Active IP Address: Displays the current IP Address.
Active Subnet Mask: Displays the current IP Subnet Mask.
Active Gateway: Displays the current Gateway.
DHCP Server: Displays the DHCP Server IP Address when DHCP check
box is enabled.
Lease Time Left: Displays DHCP lease time. After 50% of the lease time

12
has passed, the client/switch will attempt to renew the lease with the original
DHCP server that it obtained the lease from using a DHCPREQUEST
message. Any time the client/switch boots and the lease is 50% or more
passed, the client/switch will attempt to renew the lease. At 87.5% of the
lease completion, the client/switch will attempt to contact any DHCP server
for a new lease.
System Configuration Interface
DHCP Enable: Tick the check box to enable DHCP Client Function.
Fallback IP Address: Assign the fallback IP address for DHCP IP assigning

13
failure (The default IP is 192.168.16.1).
Fallback Subnet Mask: Assign the switch IP Subnet Mask.
Fallback Gateway: Assign the switch Gateway (The default value is
192.168.16.254).
TFTP Server Enabled: Tick this check box to enable the TFTP server
function.
Management VLAN (1 ~ 4095): Assign a number of VLAN group between 1
and 4095. It is used for Remote Management Security; in fact, it gives the
port permission to access the switch only when the port’s VLAN group ID is
equal to the Management VLAN ID.
Name: Assign the name of the switch.
Password: Web GUI login password. The default password is root.
Inactivity Timeout: Set the timeout period for security in number between
10 and 10000 seconds.
And then, click
Apply
to have the configuration take effect.
Or, click
Refresh
to reset the configuration before applying.
Port Configuration
Specify the negotiation mode, enable flow control, and set maximum frame size
in the range between 1518 and 9600 for each port.
Link: “Down” means “No Link”. Link speed status includes: 1000FDX,
100FDX, 100HDX, 10FDX, and 10 HDX. The system will automatically
detect link speed.
Mode: Specify the speed, full-duplex or half-duplex mode of the ports.
Flow control:Set Flow Control Function as “enable” or “disable” in Full
Duplex mode.
MaxFrame (1522 ~ 9600): Set the Maximum Frame Size in bytes for frames
received on the port.

14
Click
Apply
to have the configuration take effect.
Or, click
Refresh
to reset the configuration before Applying.
Port Configuration interface
Statistics-1 (Overview)
The following information provides the current port statistic information.
Press
Clear
button to clean all counts, and then click
Refresh
to get the
new setting information shown as below.
Statistics Overview interface

15
Statistics-2 (Detailed)
The following information provides statistics detail information on each port, and
the user can simply click the port to view the statistics information.
Press
Clear
button to clean all counts, and then click
Refresh
to get the
new setting information as below.
Statistics Detail interface
VLAN Setting
A Virtual LAN (VLAN) is a logical network grouping that limits the broadcast
domain, which would allow users to isolate network traffic, and therefore only the
members of the VLAN will receive traffic from the members of the same VLAN.
Basically, creating a VLAN from a switch is logically equivalent to reconnecting a
group of network devices to another Layer 2 switch. However, all the network
devices are still plugged into the same switch physically.
Assign the VLAN ID in number between 1 and 4095.
Group the members of VLAN by ticking the check box.
Click
Apply
to bring up the configuration interface as below.
Tick all check boxes by clicking ‘add all’ or remove all ticks by clicking ‘clear
all’.

16
There are 16 VLAN entries per page among 16 pages. To search the
specified VLAN, please type in the VLAN ID in the empty field beside the
label of ‘Quick Search Vlan Entry, Vlan ID:’ and then press ‘Search’.
VLAN Setting interface
VLAN Port Setting
Click
VLANPortSetting
to bring up the configuration interface for adjusting
the VID Setting.
PVID: Enter the Port VLAN ID.
Awareness: Enable the awareness so that ports will strip the VLAN tag from
received frames and insert the tag (contains PVID) into transmitted frames.