Midea FS40-13QRA User manual

OWNER’S MANUAL
16" MIST FAN
MODEL: FS40-13QRA
READ AND SAVE THESE INSTRUCTIONS
Version 1.0 2015
Attention: Pictures in the IM are for reference only.

IMPORTANT SAFEGUARDS
Read Rules for Safe Operation and Instructions Carefully.
Caution
1. If the supply cord is damaged, it must be replaced by manufac-
turer or its service agent or a similarly qualified person in order
to avoid a hazard.
2. To protect against the risk of electrical shock, do not immerse
the unit, cord or plug in water or other liquid.
3. This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety. Young children should
be supervised to ensure that they do not play with the appliance.
4. When the appliance is not in use and before cleaning, unplug
the appliance from the outlet.
5. Keep electrical appliances out of reach from Children or infirm
persons. Do not let them use the appliances without supervision.
6. When the fan was assembled, the rotor blade guard shall not be
taken off at any time.
7. Prior cleaning unplug the fan.
8. The rotor guard shall not be dissembled/opened to clean the
rotor blades.
9. Wipe the fan enclosure and rotor blade guard with a slightly
damp cloth.
7. Unplug the appliance during filling and cleaning.
WARNING
1

1
3 4 5 6 7 8 9
10
11
12
13
16
17
18 14
15
2
2
RULES FOR SAFE OPERATION
1. Never insert fingers, pencils, or any other object through the
grill when fan is running.
2. Disconnect fan when moving from one location to another.
3. Be sure fan is on a stable surface when operating to avoid
overturning.
4. DO NOT use fan in front of a window, rain may create
electrical hazard.
5. Household use only.
PART FIGURE

3
PART FIGURE
NO. Description NO. Description
1 Spray cap
2 Corrugated hose
10 Motor assy
3 Front guard
11 Tightening knob
4 Screw (ST3*7.5)
12 Host assy
5 Net clamp
13 Base assy
6 Blade nut
14
Caster (Universal wheel)
7 Blade
15 Screw (M5*20)
Spring clamp
Drain plug
8 Guard nut
16
17
18
9 Rear guard
Water tank assy
All the pictures in this manual are for explanation purpose only. Any discrepan-
cy between the real object and the illustration in the drawing shall be subject to
the real subject.
Note:
pilot hole
INSTALLATION METHOD
1. Assembly of host
Take out the motor assy and host assy from the
package,as is shown in Figure 1,insert the
connecting wire and the column into the host,then
tighten the fastening knob and ensure to drive the
screw into the positioning hole.
Fig.1

4
INSTALLATION METHOD
2. Mounting the casters
Take out the base and casters from the
package, as is shown in Figure 2, and press the
casters into the base mounting hole.
3. Mounting the base in the host
As is shown in Figure 3, put 3 screws (M5 * 20)
through the base, and fix the base host in the
nuts embedded in the host bottom.
4. Mounting the rear guard and blade
As is shown in Figure 4, in sequence, mount the
rear guard, guard nut, blade, blade nut and net
clamp.
5. Assembling the chassis
As is shown in Figure 5, press the spray cap into a
corrugated hose, during assembly, perform
pressing while rotating, and then with screws, fix
the spray cap on the front guard.
Fig.2
Fig.3
Fig.4
Fig.5
6. Mount the components of front guard into
the net clamp
As is shown in Figure 6, mount the front guard into
the net clamp, screw in the net clamp and then
tighten the screws; then mount the corrugated
hose on the top of host.
Fig.6

Control Panel Remote Control Panel
5
INSTRUCTIONS FOR USE
Instructions on Key Functions
After power-on, the buzzer will "beep", and the power indicator lights up.
ON/OFF
Fan power switch: When the key is pressed, the wind type is in normal mode,
low-level running is performed and room temperature is shown, and after the
button is pressed again, the fan power supply is disconnected.
SPEED
Fan level selection control by speed+ and speed-
TIMER
Fan timer switch: it cycles in the sequence of 1H-2H-4H-8H-0-1H-.
MIST
Humidification switch: For use, see the User’s Manual of Humidifier.
MODE
Wind class selector switch: it cycles in the sequence of Normal wind - Natural wind
- Sleep wind - Normal wind.
ION
An ion switch: It works after the fan, humidifier or heating function.
ECO/TEMP
Smart wind switch: It automatically selects an appropriate level according to the
temperature change.
OSC
Oscillation switch: It controls the left and right swinging.

6
If the indicator flashes (off after 10 seconds), it indicates insufficient water or low
water level, please check whether the float in the sink of the host has floated or
the water tank is properly placed.
Note:
INSTRUCTIONS FOR USE
Instructions on humidification function
•Remove the water tank from the host, and unscrew the water tank cap count-
er-clockwise.
• Fill the water tank with cold water, tighten the water tank cap and check for leakage.
•As is shown, put the water tank into the host according to the angle, and wait a few
minutes until the host sink is filled with water.
•After the humidification button is pressed, the indicator lights up to start humidifica-
tion.

7
PRECAUTIONS
• Before use, please check that the machine has been assembled completely and
fixed motor components have been mounted and fastened; before this, do not
connect the power supply.
• Before turning on the power, check whether the used voltage is the same as the
voltage indicated on the machine.
• When the appliance works, do not insert your fingers and sharp objects into the
guard or the machine body.
• Children shall use this electric appliance under adult supervision to prevent
accidents.
• Prior to use, check the power cord and plug for any damage, and if the power cord
is damaged, in order to avoid danger, be sure to have it replaced by the manufac-
turer, maintenance department or professionals with the similar qualification.
• If the appliance is left unattended or is no longer in use, turn off the power and
unplug the power cord to avoid failure problems and accidents.
• When the humidifier is used, the water tank shall use clean water below 40°, and
it is recommended to use demineralised water, pure water or distilled water
containing less impurities.
• Do not place this appliance on sloping ground to avoid tipping over, and do not
move the water tank when the humidifier is working; if the humidifier or host
accidentally tips over when it contains water, please unplug the power cord and
remove the water tank in the machine body, and reuse it after there is no hidden
security risk in the machine and especially no water accumulates in the machine
body.
• When using a humidifier, you can not add sanitizers, vinegar, perfume or essential
oils.
• When using a humidifier, never have the mist to face the furniture, appliances or
walls to avoid damage due to excessive damp.
• Water is inside the water tank or sink shall not be placed for a too long time, as this
may easily breed bacteria; change the water every 2 days, and clean the sink
once every 2-3 weeks.
•HUMIDIFIER CLEANING METHOD
• Before cleaning the humidifier, turn off the power, remove the spring clamp and
drain plug, and clear the machine of remaining water.
• After removal of the scale and use for some time, scale is prone to accumulate
inside the water tank, sink, and transducer; if scale occurs in the sink or on the
oscillating blade, a small amount of detergent is put into the water in the sink, and
cleaned with clear water after soaking for about 30 minutes.
• Mount the drain plug and spring clamp.
• Accept it carefully after continuous use or drying the machine in shade.

8
The fan requires little maintenance. Do not try to fix it by yourself. Refer it to
qualified service personnel if service is needed.
1. Before cleaning and assembling, fan must be unplugged.
2. To ensure adequate air circulation to the motor, keep vents at the rear of the
motor free of dust. Do not disassemble the fan to remove dust.
3. Please wipe the exterior parts with a soft cloth soaking a mild detergent.
4. Do not use any abrasive detergent or solvents to avoid scratching the surface.
Do not use any of the following as a cleaner: gasoline, thinner.
5. Do not allow water or any other liquid into the motor housing or interior parts.
MAINTENANCE INSTRUCTION
CLEANING
1. Be sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with a soft cloth moisten with mild soap.
Thoroughly remove soap film with dry cloth.
DISPOSAL：Do not dispose of electrical appliances as unsorted
municipal waste, use separate collection facilities. Contact you local
government for information regarding the collection systems avail-
able. If electrical appliances are disposed of in landfills or dumps,
hazardous substances can leak into the groundwater and get into
the food chain, damaging your health and well-being.