Midea FS40-15AR User manual

ELECTRIC FAN
OWNER’S MANUAL
PEDESTAL FAN
MODEL:FS40-15AR
READ AND SAVE THESE INSTRUCTIONS
Attention: Pictures in the IM are for reference only.
Distributed by JH Electrical and Appliance Ltd
570 Mt Wellington Highway，Mt Wellington，Auckland 1062，New Zealand
[phone]
145x210mm 警语3.2mm 单黑

1
Please read the safe operation rules and instructions carefully
CAUTION
1. If the power cord is damaged, it must be replaced by manufacturer
or its service agent or a similar qualified person in order to avoid
any hazard.
2. Indoor use only.
3. To prevent the risk of electrical shock, do not immerse the unit,
cord or plug in water or other liquid.
4. This appliance is not intended for use by persons (including c
hildren) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety
Young children should be supervised to ensure that they do not
play with the appliance.
5. When the appliance is not in use and before cleaning, unplug the
appliance from the outlet.
6. When the fan has been assembled, the rotor blade guard shall not
be taken off anymore.
7. Correct Disposal of this product
This marking indicates that this product should not be
disposed with other household wastes throughout the EU. To
prevent possible harm to the environment or human health from
uncontrolled waste disposal, recycle it responsibly to promote the
sustainable reuse of material resources.
WARNING
1. Never insert fingers, pencils, or any other object through the grille when fan is
running.
2. UNPLUG the fan when moving from one location to another.
3. Make sure the fan is on a stable surface when operating to avoid overturning.
4. DO NOT use the fan beside window, rain may create electrical hazard.
5. Household use only.
SAFE OPERATION RULES

22
INSTALLATION INSTRUCTIONS
Name of components
Motor
Motor shaft
Rear grill
Tighten
knob
Pole
Base
Considerate Hint:
Remove ①②③parts from the
component before performing
installation.
Base Installation
Align the column with the
groove on the base and
fix them together using
butterfly screws.
③
①
②
Butterfly screw
Install by
aligning

3
Lock nut of grill
Lock nut of blade
Blade
Screw the lock nut of grill clockwise,
and in the meantime, fix the rear grill.
Lock nut of blade
anticlockwise,
and then install the
front fan cover.
Pull the blade to rotate after installing,
so as to ensure that the blade can be
normally rotated.
Front grill
Guard
Catch
1
2
3
1
2
3
Align Catch of the Front Guard
with the illustrated position of
the Rear Guard.
Press guards sequentially
with both hands.
Self-Catch Installation.
Front and Rear Guard Installation

4
Speed / Timer
display
Instructions for remote controller
Instructions for display of body
INSTRUCTIONS FOR USE
MODE
DRIVE PLATE
ON/OFF
PRO/Timer
OSC
Considerate Hint:
1. Install the battery with positive side facing up.
2. Effective Range of Remote Control: within 5 m
distance and 30-degree deflection in front of
Product.
Battery installation
Rear
cover
PUSH OPEN
h

5
Instructions for operation of body
INSTRUCTIONS FOR USE
Body key
Tilt Adjustment
Manual
Height
Adjustment
Key
Height Adjustment
Turn counterclockwise and
loosen for performing height
adjustment.
DRIVE
PLATE

6
The fan requires little maintenance. Do not try to fix it by yourself. Refer it to
qualified service personal if service is needed.
1. Before cleaning and assembling, fan must be unplugged.
2. To ensure adequate air circulation to the motor, keep vents at the rear of the
motor free of dust. Do not disassemble the fan to remove dust.
3. Please wipe the exterior parts with a soft cloth soaking a mild detergent.
4. Do not use any abrasive detergent or solvents to avoid scratching the surface.
Do not use any of the following as a cleaner: gasoline, thinner.
5. Do not allow water or any other liquid into the motor housing or interior parts.
MAINTENANCE INSTRUCTION
CLEANING
1. Make sure to unplug from the electrical supply source before cleaning.
2. Plastic parts should be cleaned with a soft cloth moisten with mild soap.
Thoroughly remove soap film with dry cloth.