Midea RG58N2/BGEF User manual

ENGLISH
AIR CONDITIONER
REMOTE CONTROLLER ILLUSTRATION
Thank you very much for purchasing our air conditioner. Please read this owner's manual
carefully before using your air conditioner. Make sure to save this manual for future
reference.

ENGLISH
1
CONTENTS
Remote Controller Specifications ....................................................................................... 2
Function Buttons .................................................................................................................. 3
Remote LCD Screen Indicators ........................................................................................... 5
How To Use The Basic Functions ........................................................................................ 6
How To Use The Basic Functions ...................................................................................... 12
How To Use The Advanced Functions............................................................................... 13
NOTE:
● Buttons design is based on typical model and might be slightly different from the actual one you
purchased the actual shape shall prevail.
● All the functions described are accomplished by the unit. If the unit has no this feature, there is no
corresponding operation happened when press the relative button on the remote controller.
● When there are wid,,e differences between "Remote controller Illustration "and "USER'S MANUAL
"on function description, the description of "USER'S MANUAL" shall prevail.

ENGLISH
2
Remote Controller Specifications
Model
RG58N2(B2H)/BGEF
Rated Voltage
3.0V(Dry batteries R03/LR03 2)
Signal Receiving Range
8m
Environment
-5OC~60OC(23OF~140OF)

ENGLISH
3
Function Buttons
Before you begin using your new air conditioner, make sure to familiarize yourself with its remote control.
The following is a brief introduction to the remote control itself. For instructions on how to operate your
air conditioner, refer to the How to Use Basic Functions section of this manual.
NOTE˖Please do not select HEAT mode if the machine you purchased is cooling only type. Heat mode
is not supported by the cooling only appliance.

ENGLISH
4
NOT SURE WHAT A FUNCTION DOES?
Refer to the
How to Use Basic Functions
and
How to Use Advanced Fu
nctions sections
of
this anual for a detailed
description of how to use
your air conditioner.
SPECIAL NOTE
z Button designs on your unit may differ
slightly
from the example shown.
z
If the indoor unit does not have a particular
function, pressing that functio
n s button on
the remote control will have no effect.
INSERTING AND REPLACING BATTERIES
Put the two batteries(optional parts) in the remote
control before use:
1.
Remove the back cover from the remote
control, exposing the battery compartment.
2.
Insert the batteries, paying attention to
match
up the (+) and (-) ends of the
batteries with
the symbols inside the
battery compartment.
3.
Install the back cover on.
INSTALLING REMOTE CONTROL HOLDER
The remote controller can be attached to a wall or
stand by u
sing a remote controller holder.
1.
Before installing the remote controller, check
that the air conditioner receives the signals
properly.
2.
Install the holder with two screws.
3.
Put the remote controller on the holder.
BATTERY NOTES
For optimum prod
uct performance:
Do not mix old and new batteries, or
batteries of
different types.
Do not leave batteries in the remote control
if you
don t plan on using the device for
more than 2
months.
BATTERY DISPOSAL
Do not dispose of batteries as unsort
ed
municipal
waste. Refer to local laws for
proper disposal of
batteries.
TIPS FOR USING REMOTE CONTROL
z The remote control must be used w
ithin 8
meters of the unit.
z
The unit will beep when remote signal is
received.
z Curtains, other materials and direct
sunlight
can interfere with the infrared
signal receiver.
z Remove batteries if the remote control
will not
be used more than 2 months.
Remove the back cover to install batteries

ENGLISH
5
Remote LCD Screen Indicators
Note:
All indicators shown in the figure are for the purpose of clear presentation. But during the actual
operation only the relative functional signs are shown on the display window.

ENGLISH
6
How To Use The Basic Functions
COOL ope
ration
1.
Press the MODE button to select
COOL
mode.
2.
Set your desired temperature using
the Temp
or Temp button.
3.
Press the FAN button to select the
fan speed
in a range of Au-100%, in
conjunction with
Temp or Temp button.
4.
Press the ON/OFF button to start the unit.
SETTING TEMPERATURE
The operating temperature range for units is
16
-30OC/60-86OF. You can increase or
decrease
the set temperature in 0.5OC/1OF
increments.
AUTO operation
In AUTO mode, the unit will automatically
select
the COOL,
FAN, HEAT or DRY mode
based on the
set temperature.
1.
Press the MODE button to select Auto mode.
2. Set your desired temperature using the
Temp
or Temp button.
3.
Press the ON/OFF button to start the unit.
NOTE: FAN SPEED can t be set in Auto mode.

ENGLISH
7
How To Use The Basic Functions
DRY operation(dehumidifying)
1.
Press the MODE button to select DRY
mode.
2.
Set your desired temperature using the
Temp or Temp button.
3.
Press the ON/OFF button to start the unit.
NOTE:
FAN SPEED can t be changed in
DRY
mode.
FAN operation
1.
Press the MODE button to select FAN
mode.
2.
Press the FAN button to select the
fan speed
in a range of Au-100%, in
conjunction with
Temp or Temp button.
3.
Press the ON/OFF button to start the unit.
NOTE:
You can t set temperature in FAN
mode.
As a result, your remote control s
LCD screen
will not display temperature.

ENGLISH
8
How To Use The Basic Functions
HEAT operation
1.
Press the MODE button to select
HEAT
mode.
2.
Set your desired temperature using
the Temp
or Temp button.
3.
Press the FAN button to select the
fan speed
in a range of Au-100%, in
conjunction with
Temp or Temp button.
4.
ress the ON/OFF button to start the unit.
NOTE
: As outdoor temperature drops,
the
performance of your unit s HEAT function
may
be affected. In such instances, we
recommend
using this air conditioner in
conjunction with
other heating appliance.

ENGLISH
9
Setting the TIMER function
Your air conditioning unit has two
timer-
related
functions:
●
TIMER ON-
sets the amount of timer after
which the unit will automatically turn on.
●
TIMER OFF-
sets the amount of time after
which the unit will automatically turn off.
TIMER ON functio
n
The TIMER ON function allows you to set
a period
of time after which the unit will
automatically turn
on.
1.
Press the Timer button, the Timer on
indicator
" " and time display.
Note: This number indicates the
amount of
time after the current time
that you want the
unit to turn on.
For example, if you set TIMER ON for
2.5
hours, " 2.5h " will appear on the scre
en, and
the unit will turn on after 2.5 hours.
2.
Press the Temp or
Temp button
repeatedly to set the time when you
want the
unit to turn on.
3.
Wait 3 seconds, then the TIMER ON
function will be activated. The digital
display
on your remote control will then
return to the
temperature display. The "
" indicator
remains on and this function is activated
TIMER OFF function
The
TIMER OFF function allows you to
set a
period of time after which the unit
will automatically
turn off.
1.
Press the Timer button, the Timer off
indicator
" " and time display.
Note: This number indicates the
amount of
time after the current time
that you want the
unit to turn off.
For example, if you set TIMER OFF for 5
hours, " 5.0h " will appear on the screen,
and
the unit will turn off after 5 hours.
2.
Press the Temp or Temp button
repeatedly
to set the time when you want
the unit to turn
off.
3.
Wait 3 seconds, then the TIMER OFF
function will be activated. The digital
display
on your remote control will then
return to the
temperature display. The "
" indicator
remains on and this function is activated.
NOTE: When setting the TIMER ON or TIMER
OFF functions, up to 10 hours,
the time will
increase in 30 minute
increments with each press.
After 10
hours and up to 24, it will increase in 1
hour increments. The timer will revert to
zero after
24 hours.
You can turn off either function by
setting its timer
to " 0.0h "
Example:
Setting unit to turn on after 2.5
hours.
Example:
Setting unit to turn off after 5 hours.

ENGLISH
10
Setting both TIMER ON and TIMER OFF at the same time
Keep in mind that the time periods you set for both functions refer to hours after the current time. For
example, say that the current time is 1:00 PM, and you want the unit to turn on automatically at 7:00 PM.
You want it to operate for 2 hours, then automatically turn off at 9:00 PM.
Do the following:
Example: Setting the unit to turn on after 6 hours, operate for 2 hours, then turn off (see the figure
below)
Your remote display

ENGLISH
11
NOTE:
The device could comply with the local national regulations.
● In Canada, it should comply with CAN ICES-3(B)/NMB-3(B).
● In USA, this device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and receiver.
● Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
● Consult the dealer or an experienced radio/TV technician for help.
● Changes or modifications not approved by the party responsible for compliance could void user s
authority to operate the equipment.

ENGLISH
12
How To Use The Basic Functions
●
Press the SET button to enter the function
setting, then press SET button or Temp
or
Temp
button to select the desired
function.
●
The selected symbol will flash on the display
area, press the OK button to confirm.
●
To cancel the selected function, just perform
the same procedures as above.
●
Press the SET butt
on to scroll through
operation functions as follows:
Active clean (
) g Sleep( )g Follow Me( )
Active Clean Function(
)
●
This function is used to clean the air
conditioner evaporator to prevent frosting.
●
When this function is turned on, the indoor
unit
display window appears CL , after 20 to
45 minutes, the unit will turn off automatically
and cancel Active Clean function.
SLEEP Function(
)
The SLEEP function is used to decrease
energy
use while you sleep (and don t need
the same
temperature settings t
o stay
comfortable). This
function can only be
activated via remote control.
For the detail, see sleep operation in
USER S
MANUAL.
Note:
The SLEEP function is not available in
FAN or DRY mode.
FOLLOW ME function(
)(optional)
The FOLLOW ME function enable
s the
remote
control to measure the temperature
at its current
location and send this signal
to the air conditioner
every 3 minutes interval.
When using AUTO, COOL, or HEAT modes,
measuring ambient temperature from the
remote
control (instead of from the i
ndoor
unit itself) will
enable the air conditioner to
optimize the
temperature around
you and ensure maximum
comfort.

ENGLISH
13
How To Use The Advanced Functions
ECO/GEAR func
tion ( )
NOTE:
This function is only available under
COOL
mode.
•
Press ECO/GEAR butto
n to enter the energy
efficient mode in a sequence of following:
ECO ė
ė
GEAR(75%)
ė
GEAR(50%)
ė
Previous setting mode
ė
* ECO
ė
......
ECO operation:
• Under cooling mode, press this button, the
remote controller will adjust the temperature
automatically to 24°C, fa
n speed of Auto to
save energy(but only if the set temperature is
less than 24°C). If the set temperature is
above 24°C , press the ECO button, the fan
speed will change to Auto, the set
temperature will remain unchanged.
NOTE:
•
Pressing the ON/OFF butto
n, modifying the
mode or adjusting the set temperature to less
than 24°C will stop ECO operation.
• Under ECO operation, the set temperature
should be 24°C or higher, it may result in
insufficient cooling. If you feel uncomfortable,
just press the ECO button again to stop it.
GEAR operation:
• Press this button to enter the energy efficient
mode in a sequence of following:
75% (up to 75% electrical energy
consumption)
Ę
50% (up to 50% electrical energy
consumption)
Ę
Previous setting mode
•
This function is onl
y available under COOL
mode.
• Under GEAR operation, the display on the
remote controller will alternate between
electrical energy consumption and set
temperature.
TEMP Button
Press and hold
and
buttons together for 3
seconds will alternate the temperature display
between the °C & °F scale.

ENGLISH
14
How To Use The Advanced Functions
FP function
When the air
conditioner operates under heating
mode with the set temperature of 16°C(60°F),
pressing
button twice in two seconds will
activate 8°C(46°F) heating. The indoor unit display
shows "FP".
For some units, press this button can activate 12°C
heating feature, please refer to the" Owner's
Manual" of the air conditioner.
Silence function
Hold down Fan speed button( ) tor 2 seconds
to activate/cancel Silent mod
e. Due to
low
frequency operation of compressor, it may result in
insufficient cooling and heating capacity
(applicable to the air conditioner with Silent feature
only)
Boost funct
ion( )
The Boost function makes the unit work extra hard
to reach your present temperature in the shortest
amount of time possible.
•
When you select Boost feature in COOL
mode, the unit will blow cod air with strongest
wind setting to jump-
start the cooling process.
• When you select Boost feature in HEAT
mode, the unit will blo
w heat air with
strongest wind setting to jump-
start the
heating process.
Swing
Button
Used to stop or start vertical louver movement and
set the desired left/right air flow direction. The
vertical louver changes 6 degree in angle for each
press. If keep
pushing more than 2 seconds, the
vertical louver auto swing feature is activated.
Swing
Button
Used to stop or start horizontal louver movement
or set the desired up/down airflow direction. The
louver changes 6 degree in angle for each press. If
keep pushing more than 2 seconds, the louver will
swing up and down automatically.
NOTE:
When the unit is off, press and hold Mode and
buttons together for one second, the louver will
open for a certain angle, which makes it very
convenient for cleaning.
Pre
ss and hold Mode and buttons
together for
one second to reset the
louver.

ENGLISH
The design and specifications are subject to change without prior notice for product
improvement. Consult with the sales agency or manufacturer for details.