Mighty Mule GTO PRO MM371W User manual

Installation Manual
Wireless Vehicle Sensor

2
Kit Includes:
A. Transmitter Module
B. Sensor
C. Mounting Post (3 pieces)
D. 2 “AA” Batteries (Note: lithium-alkaline batteries are required for extreme cold climates.)
E. Receiver (RB709U-NB)
A
CD
B
E
Kit Contents
Table of Contents
Kit Contents .....................................................................................2
How it Works ....................................................................................3
1. Program DIP Switch Settings .......................................................................................4
2. Determine Location for Sensor and Transmitter Module...................................................................5
3. Install Sensor and Transmitter Module ................................................................................6
4. Do you have a Mighty Mule®MM371W, MM372W, MM571W, MM572W, TS571W, MM271, MM272 or HD272 Automatic Gate Opener? ......7
Learning an FM130 to an MM371W, MM372W, MM571W, MM572W, TS571W, MM271, MM272 or HD272 Automatic Gate Opener............7
Learning an FM130 to an MM271, MM272 or HD272 Automatic Gate Opener ...................................................7
Instructions for Installing the Optional RB709U-NB Receiver ..............................................8
5. Test the System..................................................................................................10
Troubleshooting Guide.............................................................................11
Limited Warranty ................................................................................12
FCC Warning ....................................................................................12

3
How it Works
The electromagnetic sensor detects vehicles in motion and automatically activates your gate. This “hands
free” device allows friends, family and delivery personnel to exit your property without the need of an Entry
Transmitter, or you, to operate the gate.
When a VEHICLE SENSOR is in use, the automatic gate opener could
be activated by a child on a bicycle, tricycle or other metal play
equipment. DO NOT ALLOW UNATTENDED CHILDREN OR PETS
NEAR YOUR AUTOMATED GATE AT ANY TIME.

4
1. Program DIP Switch Settings
Do you have a Mighty Mule MM371W, MM372W, MM571W, MM572W, TS571W, MM271, MM272 or HD272
Automatic Gate Opener? If so, skip to page 7 for instructions.
Step 1: Verify that your Entry Transmitter operates the gate opener.
Step 2: Remove the cover (A) from your gate opener Entry Transmitter (B). Remove the cover (C) from the Transmitter
Module (D).
Step 3: You will change the DIP Switch settings on the Transmitter Module to match those of your Entry Transmitter.
Do not change the DIP switches on the Entry Transmitter.
For Single Button Entry Transmitters, set the 9 DIP Switch settings on the Transmitter Module to match the 9 DIP Switch
settings of the Entry Transmitter.
For Dual Button Entry Transmitters, set the rst 8 DIP Switch settings on the Transmitter Module to match the 8 DIP
Switch settings of the Entry Transmitter. The 9th DIP Switch setting (Transmitter Module) will depend on which button
you use to operate the gate (see illustration above).
WIRELESS VEHICLE SENSOR
TRANSMITTER CODE
TRANSMITTING
MIN MAX
SENSITIVITY
+
o
-
123456789
Sensitivity
Adjustment
DIP Switches
Transmit Indicator
If you use this button
to operate gate, put
the 9th DIP Switch in
the “+” position
If you use this button
to operate gate, put
the 9th DIP Switch
in the “0” position
Dual Button Entry Transmitter
Transmitter Module
1 2 3 4 5 6 7 8 9
ECE
A23S 12V
A23S 12V
ALKALINE BATTERY
ALKALINE BATTERY
+
0
–
LED
Transmitter Module
and Cover
MIN MAX
SENSITIVITY TRANSMITTER CODE
TRANSMITTING
12 3 4
CD
Single Button Entry Transmitter and Cover Transmitter Cover and Module
A
B

5
2. Determine Location for Sensor and Transmitter Module
NOTE: Install Transmitter Module and Sensor on the same side of the driveway as your automatic gate
opener/receiver.
Placement of SENSOR:
• No more than 2 ft. from edge of driveway.
• Same side of driveway as the gate opener control box.
• At least 25 ft. from leading edge of open gate, roadways, neighboring driveways, etc.
• Parallel to direction of the driveway.
Placement of TRANSMITTER MODULE:
• No more than 100 ft. from gate opener receiver.
• Within “line of sight” of the gate opener receiver.
• Away from lawn sprinklers (Transmitter Module is water resistant, not waterproof).
• Away from the driveway edge so that vehicles are unlikely to hit it.
For Optimum Performance:
• Install the Sensor as far away as possible from power transformers, power lines, underground gas lines and
telephone lines.
• Locate the Sensor away from general moving trafc to prevent unwanted activation (the Sensor detects magnetic
disturbances caused by a vehicle’s mass and velocity).
• It is recommended that you run the Sensor Cable inside PVC conduit to prevent damage.
• Do not run Sensor Cable in conduit with other wires such as AC power or other control wires.
• THE SENSOR CABLE MUST NOT BE SPLICED.
DRIVEWAY
ROADWAY
TRANSMITTER
MODULE
Sensor Range:
12' radius
SENSOR:
up to 2' (max.)
from driveway
25' (min.) from leading
edge of open gate
Sensor Cable
Gate Opener
Receiver
25' (min.)
from neighbor’s
driveway
Transmitter Signal
100' (max.)
Sensor Range distance is approximate and will vary
due to outside interference, vehicle mass, speed, etc.

6
Connect Sensor Cable
to Transmitter Module
Leave 2" of slack
in the Sensor Cable
MIN MAX
SENSITIVITY TRANSMITTER CODE
TRANSMITTING
12 3 4
A
B
C
3. Install Sensor and Transmitter Module
IMPORTANT: Clear an area 25 ft. in all directions of metal tools, toys and automobiles that may move to prevent magnetic
disturbance during testing and installation.
Step 1: Dig a hole for the Sensor, 10–12 in. deep and 24 in. long. Be sure the hole is parallel to the direction of the
driveway and not more than 2 ft. away from the driveway.
Step 2: Dig a trench in which to lay the Sensor Cable from this hole to where you want to install the Transmitter Module.
The trench should be at least 6 in. deep to prevent possible wire damage from edgers, lawn aerators, etc.
Step 3: Lay the Sensor in the hole parallel to the driveway and the Sensor Cable in the trench. Do not ll/cover the hole
or trench until the Transmitter Module signal has been tested (page 5). If you don’t use the full length of Sensor Cable,
coil the extra cable beside the Mounting Post.
Step 4: Assemble the Mounting Post using the coupler to connect the two longer pieces.
Step 5: Run the Sensor Cable (B) through the Mounting Post (A) and plug it into the connector at the bottom of the
Transmitter Module (C). Allow 2 inches of slack in the cable to prevent damage to the connector if Transmitter Module is
removed.
Step 6: Attach the Transmitter Module to the Mounting Post. At this point, you can put the Mounting Post in the ground,
but don’t ll the hole until after testing (page 5).
Transmitter Module
approximately 12" above ground.
Leave 2" of wire slack
inside post.
DRIVEWAY
Place Sensor 10-12" deep
and parallel to driveway.
Coil extra wire.
To Gate

7
4. Do you have a Mighty Mule MM371W, MM372W, MM571W,
MM572W, TS571W, MM271, MM272 or HD272 Automatic
Gate Opener?
If so, these openers DO NOT require a receiver. Read the pairing instructions below:
The MM360 and select legacy systems require the installation of the RB709U-NB Universal Receiver. See
pages 8-9 for instructions on how to do so.
Learning an FM130 to an MM371W, MM372W, MM571W, MM572W or TS571W Automatic Gate
Opener.
1. With the power on for your control box, press and
hold the gate opener's middle, orange S3 button
(to the left of “S3” in the diagram) located on the
control board until you hear a beep, then release.
2. Take a battery out of the green FM130 transmitter
and put it back in. The control board should
beep.
3. Test the FM130 by closing the gate and removing
and replacing a battery in the green FM130
transmitter. If the gate opens, the FM130 has
been properly programmed to your control board.
4. Proceed to page 7: "Install Sensor and
Transmitter Module".
NOTE: If you hear three short beeps in succession, the
programming mode has timed out and you will need to
redo Steps 1-3.
To forget the FM130, simply follow steps 1 and 2 above
to verify that it no longer activates the AGO.
Learning an FM130 to an MM271, MM272 or HD272 Automatic Gate Opener
1. Use the On/Off switch on the control box to power the system down.
2. Take the battery out of the green FM130 transmitter and put it back in.
3. While the red light is blinking on the FM130 transmitter, power the system on with the On/Off switch on the
control box
4. After the startup beep, there will be a long silence for about 10 seconds, followed by a continuous beep sound.
5. Test the FM130 by closing the gate and removing and replacing a battery in the green FM130 transmitter. If the
gate opens, the FM130 has been properly programmed to your control board.
6. Proceed to page 7: “Install Sensor and Transmitter Module”.
To forget the FM130, simply follow steps 1-5 above then test the sensor to verify that it no longer activates the AGO.
NOTE for MM271: The gate must be in the closed position with the arm extended to delete the FM130. The gate can be
in any position to learn it.
IF THE PROCESS FAILS ON THE MM271, MM272 or HD272: You must use a Mighty Mule transmitter with DIP switches
(FM134, FM135, MM3BT, RB741, or RB742) to program the FM130. Simply match the DIP switch patterns between the
transmitter and FM130 then learn the transmitter to the system.
Contact Tech Support for a complimentary Mighty Mule transmitter with DIP switches to program the FM130 if you do
not have one.
S4
S3
S2
LED1
LED2
LED3

8
Instructions for Installing the Optional RB709U-NB Receiver
Step 1: The RB709U-NB will replace the gate opener receiver; disconnect
the gate opener receiver’s RED, BLACK and GREEN wires from the receiver
terminals on the gate opener control board.
Step 2: Mount the RB709U-NB Receiver.
• The Receiver can be mounted up to 10 ft. from the gate opener control
board.
• DO NOT mount the Receiver upside down.
• DO NOT mount on a metal surface (will reduce range).
• Run Receiver cable through PVC conduit to protect it from damage.
• DO NOT run Receiver cable in conduit containing AC wiring.
• Receiver range can vary depending upon weather, topography and external
interference.
Step 3: Connect the RED and BLACK wires from the Receiver to the power
supply (see illustration, page 5).
CAUTION: The “Learn” process may activate the gate. Please use caution when programming the Receiver.
Note: You will have to use a small screwdriver or a pen to depress
the LEARN CH buttons on the receiver.
Step 4: Connect the Receiver’s Channel 1 wires (GREEN and
BLUE) to your control board (see illustration, page 5). Press and
hold the Entry Transmitter button then the Receiver’s LEARN CH
1 button at the same time. The indicator light on the Receiver
should blink once within 1–2 seconds to indicate that the Entry
Transmitter setting is now programmed into the Receiver.
RCVR
GRN
BLK
RED
RCVR
R B G
RECEIVER
BLKGRN RED
Receiver Terminal Blocks
CAUTION: The “Learn” process may activate the gate. Please use
caution when programming the Receiver.
*RB709U-NB Receiver is only required for installations on MM360 systems and
select legacy systems. Please call technical support for details.
Indicator Light
Learn Channel Buttons

9
VAR5
VAR6
K1
PF1
K2
BATT +
BATT –
K3 K4
VAR4 VAR3 VAR2 VAR1
MIN MAX OFF
≤JP1
REMOVE JUMPER FOR PUSH TO OPEN OPTION
120
SEC.
GTO Inc. Tallahassee, FL
R4722
STALL FORCE
OPEN < JOG > CLOSE
PWR. SET
LIMIT
1st OPR.
2nd OPR.
STATUS
AUTO CLOSE
SFTY.
EXIT
CYCLE
EDGE
SENSOR
COMMON
LOCK+
LOCK–
WHT
GRN
RED
BLK
WHT
GRN
SECOND OPR.FIRST OPR.
RED
BLK
14 VAC
OR
SOLAR
ON OFF
BLUE
RED
BROWN
BLACK
YELLOW
GREEN
Control Board Wiring
MM271 Wiring Diagram
POWER
CHGR
CHGR
EDGE
CYCLE
EXIT
SAFETY
COM
COM
LOCK+
LOCK -
Battery
BROWN
RED
BLACK
YELLOW
BLUE
GREEN
POWER
AUX
OUT
SOLAR
INPUT
18VAC/
RCVR
GRN
BLK
RED
EXIT
SAFETY
EDGE
CYCLE
COMMON
LINK
H L
CH 1 (Green Wire to Com)
CH 1 (Blue Wire to Cycle)
CH 2 (Yellow Wire to Exit)
CH 2 (Brown Wire to Com)
RED to
AUX OUT H
BLACK to Com
RECEIVER
COM COM
CYCLE CLOSE SAFETY EXIT/ OPEN SHADOW LOOP CLOSE EDGE OPEN EDGE
BLKGRN RED
STALL FORCE
M
I
N
M
A
X
Gate Opener Battery
RED WIRE to POSITIVE
BLACK WIRE to NEGATIVE
CH 1 (Green Wire to Com)
CH 1 (Blue Wire to Cycle)
CH 2 (Yellow Wire to Exit)
CH 2 (Brown Wire to Com)
RED
BLACK
GREEN WIRE
BLUE WIRE
BLACK RED
BROWN WIRE
YELLOW WIRE
Step 5: Connect the Receiver’s Channel 2 wires (YELLOW and BROWN) to your control board (see illustration above).
Step 6: Have a helper install the 2 “AA” batteries in the Transmitter Module: this will immediately start 30 seconds of
transmission from the Wireless Vehicle Sensor. During the 30 second transmission, press and hold the Receiver’s LEARN
CH 2 button. The indicator light on the Receiver should blink twice within 1–2 seconds to indicate that the Wireless
Vehicle Sensor setting is now programmed into the Receiver.
Step 7: Proceed to “Test the System”.
MM272 and PRO-
SW2000XLS Series
Wiring Diagram
MM371W, MM372W, MM571W
MM572W and TS571W Wiring Diagram
NOTE: This diagram also
works with MM260.
NOTE: This diagram also works
for MM262, MM362 and MM462.

10
5. Test the System
Step 1: Make sure gate opener is turned ON and gate is in the closed position.
Step 2: Remove and install 2 “AA” batteries (included) in the Transmitter Module; the gate will open. Wait 60 seconds
before proceeding to the next step and DO NOT move the sensor, any vehicles, or metal objects that are within 25 ft. during this
calibration/”self-test” 60-second period.
Step 3: Use your Entry Transmitter to close the gate. Test the Wireless Vehicle Sensor by driving your vehicle past the
Sensor at normal driveway speed. The gate should open each time; if it does not, use a small screwdriver to increase the
Sensitivity Adjustment (clockwise rotation).
Step 4: Once operation is satisfactory, turn the gate opener OFF. Fill the holes and trench with soil and tamp rm. The
bottom third of the Mounting Post should be buried rmly in the ground.
Step 5: Turn the gate opener ON and make sure gate is in the closed position. Replace Transmitter Module cover and
test the system again (Step 3).
NOTE: Do not cover the Transmitter Module with anything metal, as this will cause signal interference.
Your installation is now complete. If your Wireless Vehicle Sensor is not working properly, please refer to the
Troubleshooting Guide on back cover.
GTO WIRELESS EXIT WAND
TRANSMITTER
MIN MAX
SENSITIVITY