DMP Electronics 734 Installation guide

INSTALLATION AND PROGRAMMING GUIDE
734 Wiegand
Interface Module

About the 734............................................. 1
Power Supply......................................................... 1
Zone Terminals ...................................................... 1
Annunciators.......................................................... 1
Indicator LEDs ....................................................... 1
Form C Relay......................................................... 2
Programming Connection................................ 2
Keypad In and Out Connections ................... 2
PCB Features...............................................3
Install the 734 .............................................4
Wire the Magnetic Lock.................................... 5
Isolation Relay (optional) ................................. 7
Install the 333 Suppressor ............................... 8
Wire the Zone Terminals................................... 9
Connect a Card Reader (optional) ............... 11
Set the 734 Address..........................................14
TABLE OF CONTENTS
Program the 734....................................... 17
Program Start Display ......................................18
Initialization Option ...........................................18
Initialize Confirm Option .................................18
Activate Zone 2 Bypass...................................19
Zone 2 Bypass Time.........................................20
Relock on Zone 2 Change..............................20
Activate Zone 3 Request to Exit ..................21
Zone 3 REX Strike Time..................................22
Activate Onboard Speaker............................ 22
Card Formats ......................................................22
Custom Card Definitions .........................23
Card Format Number.......................................23
Format Name......................................................24
Wiegand Code Length....................................24
Site Code Position and Length .................... 25
User Code Position and Length...................25
Require Site Code .............................................26
Site Code Display ..............................................26
Number of User Code Digits......................... 27
No Communication with Panel ....................28
Remove Keypad.................................................29

Keypad Bus Wiring Specifications........ 30
Public Card Formats ................................ 31
Compliance Listing Specifications ........32
UL Commercial Fire..........................................32
UL Access Control.............................................32
ULC Commercial Burglary (XR150/XR550
Series Panels)......................................................33
Certifications............................................ 34
Underwriters Laboratory (UL Listed)........34
Product Specifications ............................35
Readers and Credentials ........................ 36

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 1
Annunciators
An onboard programmable piezo provides
local annunciation at the 734. You can
also connect a variety of switched ground
annunciators to the 734 for remote
annunciation.
Indicator LEDs
The 734 provides three indicator LEDs. The
red LED turns on for the same duration
as the door strike relay. The yellow LED
turns on for one second to indicate receipt
of a valid Wiegand input. The green LED
indicates that data is being sent to the
panel.
The 734 Wiegand Interface Module allows you to use the powerful built‑in access control
capability of DMP Panels. DMP panels provide access control, arming, and disarming
using proximity, mag‑stripe, biometric, or other Wiegand‑output authentication devices.
Connect a 734 to a DMP panel’s keypad bus or AX‑Bus™ to use the powerful built‑in
access control capability of DMP panels. The 734 includes the following features:
Power Supply
The 734 operates at 12/24VDC from
the power supply supporting a door’s
magnetic lock or door‑strike.
Warning: To avoid the risk of
equipment damage, do not exceed
750mA total output current for zones
connected to the module.
Zone Terminals
Zones 1, 2, and 3 on the 734 can be
programmed for a variety of burglary
or access control applications. Zone 4
is a class B, style A circuit that may be
programmed as a fire zone.
ABOUT THE 734

2 734 Installation and Programming Guide | Digital Monitoring Products, Inc.
Form C Relay
The 10Amp Form C relay draws up to
35mA of current. Refer to the NC/C/NO
(Dry Contact Relay) and the Isolation
Relay sections in this document for more
information.
Programming Connection
The 734 also provides a keypad
programming connection that allows
you to use a standard DMP LCD keypad
for initial setup. Programming can be
completed using a keypad connected
to the 734 or from XR150/XR550 Series
panels.
Keypad In and Out
Connections
The keypad in (KYPD IN) connection
receives and transmits data to the panel
keypad bus or AX‑Bus.
The keypad out (KYPD OUT) connection
receives and transmits data out to other
keypads or modules. Install a dual
connector four‑position harness to allow
daisy chain connection to other devices,
up to the maximum number of devices
supported. XR150Series panels support
up to 8devices. XR550Series panels
support up to 16devices. When using the
AX‑Buses with XR550 devices, you can
have 32 doors, expandable to 96.
Caution: When the 734 is powered
from 24VDC, do not connect devices
to KYPD OUT header.

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 3
PCB FEATURES
RED
PROG
J2
RED
J5
J4
KYPD OUT
S1
J3
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NC
C
NO
GRN
YEL
RED + –
ON
Piezo
1234 5 6 7 810 11 12 13 14
9
LC ASRED WHT GRN BLK Z1 Z2 Z3 Z4+ Z4–RA GND GND
KYPD IN RED
Door Relay
Terminal
Wiegand
Inputs
Status
Indicator
Outputs Zones
To Panel
Keypad Bus
or AX‑Bus
To Other
Keypad Bus
or AX‑Bus
Piezo
Indicator
LEDs
Keypad
Programming
Header
Address DIP
Switches
Figure1: PCB Features

4 734 Installation and Programming Guide | Digital Monitoring Products, Inc.
INSTALL THE 734
Mount the 734
The module comes in a high‑impact plastic housing that you can mount directly to a
wall, backboard, or other flat surface.
For easy installation, the back and ends of the 734 housing have wire entrances. The
back also contains multiple mounting holes that allow you to mount the module on a
single‑gang switch box. DMP recommends mounting the 734 near the protected door.
See Figure2 for mounting hole locations on the housing base.
1
1. Remove the PCB from the
plastic housing by loosening
the clips on one side and gently
lifting it out of the housing base.
2. Insert the included screws in the
desired mounting hole locations
and tighten them to secure the
housing to the surface.
3. Reinstall the PCB in the housing
base.
Mounting Holes
Figure2: Mounting Hole Locations

Digital Monitoring Products, Inc. | 734 Installation and Programming Guide 5
Wire the Magnetic Lock
The 734 provides a Form C (SPDT) relay for controlling locks and other
electronically‑controlled barriers. The three relay terminals marked NO C NC allow
you to connect the device wiring to the relay for module control.
Use an additional power supply to power magnetic locks and door strikes. See
Figures 3 and 4 for typical magnetic lock and door strike wiring.
The Form C relay draws up to 35mA of current and contacts are rated for 10Amps
(resistive) at 12/24VDC. When connecting multiple locks to the Form C relay, the
total current for all locks cannot exceed 10Amps. If the total current for all locks
exceeds 10Amps, problems may arise and an isolation relay may be needed. See the
Isolation Relay section for information.
2
PROG
J2
RED RED
KYPD IN
J4
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NCCNO
GRNYELRED
Model 333
Suppressor
Normally Closed
–
+
Magnetic Door Lock
12/24 VDC
Power Supply
PROG
J2
RED
J1
DATA
XMT LED
WIEGAND
READ LED
RELAY
ON
NCCNO
GRNYELRED
Model 333
Suppressor
Normally Open
–+
DC Door Strike
12/24 VDC
Power Supply
Figure4: Typical Door Strike WiringFigure3: Typical Magnetic Lock Wiring

6 734 Installation and Programming Guide | Digital Monitoring Products, Inc.
KYPD IN / KYPD OUT Connections
• KYPD IN (Keypad In): Receives and transmits data to the panel Keypad bus/AX‑
Bus.
• KYPD OUT (Keypad Out): Receives and transmits data out to other keypad(s) or
module(s). Install a dual‑connector harness to allow connection to other devices
up to the maximum number of devices supported.
When the 734 is powered from 24VDC, do not connect devices to KYPD OUT header.
Status LEDs
The 734 board contains three status LEDs.
• The Red LED turns on for the same duration as the door strike relay.
• The Yellow LED turns on for one second to indicate receipt of a valid Wiegand
input.
• The Green LED indicates data sent to the panel.