Milesight LoRaWAN UG6 Series User manual

UG6x
All software & files can be downloaded from
https://www.milesight-iot.com/documents-download/
Cloud App Quick Start Guide
Milesight IoT Co., Ltd. www.milesight-iot.com LoRaWAN Gateway

Table of Contents
1.Packing List………………………………………………………………………………..........................
2.Hardware Introduction………………………………………………………………………………………..
3.Fitting Installation………………………………………………………………….............................
4.PoE Supply………………………………………………....................................................……
5.Gateway Installation……………………………………………..........................................…
6.Web GUI Access…………………………………………………...................................…………
2
3
5
8
8
10
11
www.milesight-iot.com

www.milesight-iot.com www.milesight-iot.com
1. Packing List
Please check the package contents to verify that you have received the items below.
2. Hardware Introduction
12 131 2 13
UG65 Mounting Bracket
Bracket Fixing Screws
Antenna Clamp Kit Antenna Coaxial
Cable
DC Power
Cable
Hose Clamp
LoRa Antennas Mounting Bracket Cable Gland
Wall Mounting Kits
Wall Mounting Kits Quick Start Guide Warranty Card
Warranty Card
Ethernet Cable
DC Jack Power
Adapter
LoRa Antenna
(EA version included)
Type-C Cable &
Power Adapter (Optional)
Quick Start Guide
Ethernet Cable Wall Mounting Kits
UG63
UG63
UG65
UG67
UG63
Quick Start Guide Warranty Card
UG67
SIM Dust Cover
PoE Injector
If any of the above items is missing or damaged, please contact your sales
representative.
Ethernet Port (PoE)
Type-C Port
Reset Button
LED Area

www.milesight-iot.com www.milesight-iot.com
3. Fitting Installation
1 4
UG65 UG67
LED Area
LoRa Antenna Connector
(only for external antenna version)
Internal Antenna
Type-C Port
Reset Button
Bracket Mounting
Holes
Ethernet Port
(PoE) Power Connector
SIM Slot
LoRa Antenna
Connector
Vent Plug
SIM Slot
Mounting Bracket
Ethernet Port (PoE)
DC Power Connector
LED Area & Type-C Port
& Reset Button
Press and hold the reset button for more than 5 seconds until STATUS/SYS LED is rapidly
blinking.
Step 1: Insert the SIM card into the device according to arrows as follows. If you need
to take out the SIM card, press the SIM card and it will pop up automatically.
How to reset the device to factory default?
5

www.milesight-iot.com www.milesight-iot.com
Step 2: UG6x supports multiple LoRa antenna types. For internal antenna mode,
keep device positive outwards to ensure it can get good signal. For single external
antenna mode, rotate the antenna into the antenna connector and ensure the
antenna is installed vertically.
Step 3: Install the power cable and Ethernet cable accordingly.
For two external antennas mode (UG67), rotate the antenna coaxial cable to one of
the connectors (ANT1 is recommended), then connect the antenna to coaxial cable.
When fixing the antenna, pass the antenna through the clamp and fix with screws,
then wrap the U-bolt around a pole and fix it to clamp with nuts and other accessories.
Note:
UG6x does not support hot plugging (also called hot swapping). Please turn
off the power before you insert or take off cards.
Please tighten the SIM dust cover of UG67 with wrench to prevent water into
the equipment.
Note: For UG67, the external antenna must be installed on ANT1 connector.
For DC power supply, remove the protective cap of power connector and rotate the
DC power cable into the power connector.
1 6 17
Screw Bolt
Rubber Ring
Screw Nut
LAN
UG65: After connecting the Ethernet cable and power cable to corresponding
interfaces, you can pass them through the waterproof silicone and slide into the
grooves. Then screw the protective cover back to the device.
UG67: Pass the Ethernet cable through the cable gland and rotate the cable gland
to gateway, then tighten the cable gland with wrench.

www.milesight-iot.com www.milesight-iot.com
4. PoE Supply
5. Gateway Installation
UG6x can be powered by 802. 3af standard PoE injector or other PoE devices.
Besides, they support DC supply via different kinds of power interfaces.
15
1 8 19
UG63
UG67
PoE Switch
Ethernet Cable
(Power & Data)
Ethernet Cable
(Power & Data)
Ethernet Cable
(Data)
Power Adapter
PoE Injector
Switch
Before you get started, make sure all fittings are installed and the power supply
is disconnected.
UG63
UG65 & UG67
Desktop: Take off the baffle and mounting plate on the back of the device, then you
can place the device on the desktop.
Ceiling or Wall Mounting: Take off the mounting plate on the back of the device,
drill 2 holes on the wall or ceiling according to the mounting plate, then fix the wall
plugs into the wall or ceiling. Fix the mounting plate to the wall plugs with screws,
then turn the device clockwise to lock it to the mounting plate.
Step 1: Mounting Bracket Mounted
Wall mounting: Align the mounting bracket horizontally to the desired position on
the wall, use a marker pen to note four mounting holes on the wall, and then remove
the mounting bracket from the wall. Drill four holes with a depth of 32mm by using
your drill with a 6mm drill bit on the positions you marked previously on the wall
and insert four wall plugs into the holes respectively. Mount the mounting bracket
horizontally to the wall by fixing the wall mounting screws into the wall plugs.

www.milesight-iot.com www.milesight-iot.com
6. Web GUI Access
Screw the bracket mounting screws behind the device and hang the device to the
mounting bracket via bracket mounting screws on the back of device.
Step 2: Gateway Mounted.
Pole mounting: Straighten out the hose clamp and slide it through the rectangular
rings in the mounting bracket, wrap the hose clamp around the pole. After that use
a screwdriver to tighten the locking mechanism by turning it clockwise.
110 111
UG6x provides web-based configuration interface for management. If this is the
first time you configure the gateway, please use the default settings below:
ETH IP Address: 192.168.23.150
Wi-Fi IP Address: 192.168.1.1
Wi-Fi AP: Gateway_******
Username: admin
Password: password
Browser: Chrome (recommended)
Here are 2 ways of accessing the web GUI:
Note:
Wireless Mode: Enable Wireless Network Connection on your computer and
search for access point " Gateway_******" to connect it. Then, type 192.168.1.1 to
your Internet browser to log in the web GUI of UG6x. This mode only works with
UG65 and UG67.
Wired Mode: Connect UG6x to your computer via Ethernet port and configure
the IP address of computer manually, then type 192.168.23.150 to your browser
to log in the web GUl of UG6x. You can follow the steps below to configure computer
IP address manually based on Windows 10 system.
A. Go to " Control Panel "→" Network and Internet " →" Network and Sharing Center ",
then click " Ethernet " (It may have different names).
B. Go to "Properties" →"Internet Protocol Version 4 (TCP/IPv4) "and select "
“Use the following IP address”, then assign a static IP manually within the same
subnet of UG6x.
Milesight 5G

LoRaWAN
Gateway
Thank you
for choosing
Milesight Product
112
www.milesight-iot.com
Milesight IoT Co., Ltd.
®

200g铜版纸+80g双胶纸
UG6X
120x85mm
封面覆哑膜（翻页版）
44.005.000117
V1.2
客 户
编 码
机 型
材 质
尺 寸
工 艺
版 本