Milesight UR32L User manual

1
UR32L Router
Quick Guide
Xiamen Milesight IoT Co., Ltd.

2
Welcome
Thank you for choosing Milesight UR32L industrial cellular router.
This guide describes how to install the UR32L and how to log in the Web GUI to configure the device.
Once you complete the installation, refer to the Milesight UR32L User Guide for instructions on how to
perform configurations on the device.
Related Documents
Document
Description
UR32L Datasheet
Datasheet for UR32L industrial cellular router.
UR32L User Guide
Instruction on how to log in the web GUI, and how to configure all the settings.
Declaration of Conformity
UR32L are in conformity with the essential requirements and other relevant provisions of the CE, FCC,
and RoHS.
Copyright © 2011-2021 Milesight.All rights reserved.
All information in this guide is protected by copyright law. Whereby, no organization or individual shall
copy or reproduce the whole or part of this user guide by any means without written authorization from
Xiamen Milesight IoT Co., Ltd.
For assistance, please contact
Milesight technical support:
Email: [e-mail]
Tel: [phone]
Fax: [phone]
Revision History
Date
Doc Version
Description
Apr. 13, 2021
V 1.0
Initial version

3
1. Packing List
Before you begin to install the UR32L router, please check the package contents to verify that you have
received the items below.
1 × UR32L
1 × Ethernet Cable
1 × Power Adapter
1 × Magnetic Cellular
Antenna
1 × Stubby Cellular
Antenna (Optional)
If any of the above items is missing or damaged, please contact your sales representative.
1 × DIN Rail Kit
Setscrews
1 × Warranty Card
1 × Quick Start Guide

4
2. Hardware Introduction
2.1 Overview
2.2 Dimensions (mm)
2.3 LED Indicators
LED
Indication
Status
Description
POWER
Power Status
Off
The power is switched off
On
The power is switched on
SYSTEM
System Status
Green Light
Static: Start-up
Blinking slowly: the system is running properly
Red Light
The system goes wrong
1Cellular Antenna Connector
2LED Indicator Area
POWER: Power Indicator
SYSTEM: Status Indicator
SIM : Status Indicator
: Signal Strength Indicator
3Ethernet LAN1/WAN Port
4Ethernet LAN2 Port
5Power Connector
6SIM and Reset Button Holder

5
SIM
SIM Card Status
Off
SIM is registering or fails to register (or there are no SIM
cards inserted)
Green Light
Blinking slowly: SIM has been registered and is ready for
dial-up
Blinking rapidly: SIM has been registered and is dialing
up now
Static: SIM has been registered and dialed up
successfully
Signal
Strength
Signal 1/2/3
Off
No signal
Green Light
Static/Off/Off: weak signals with 1-10 ASU (please
check if the antenna is installed correctly, or move the
antenna to a suitable location to get better signal)
Static/Static/Off: normal signals with 11-20 ASU
(average signal strength)
Static/Static/Static: strong signals with 21-31 ASU
(signal is good)
2.4 Reset Button
Reset button is under the SIM slot.
Function
Description
SYSTEM LED
Action
Reset
Blinking
Press and hold the reset button for more than 5 seconds.
Static Green →
Rapidly Blinking
Release the button and wait.
Off →Blinking
The router is now reset to factory defaults.
2.5 Ethernet Port Indicator
Indicator
Status
Description
Link Indicator (Orange)
On
Connected
Blinking
Transmitting data
Off
Disconnected

6
3. Hardware Installation
3.1 SIM Card Installation
A. Unscrew the cover of the SIM card then B. Put SIM card into the slot and screw it up.
take it off.
3.2 Antenna Installation
Rotate the antenna into the antenna connector accordingly.The external antenna should be installed
vertically always on a site with a good signal.
3.3 Router Installation
The router can be placed on a desktop or mounted to a wall or a DIN rail.
3.3.1 Wall Mounting (Measured in mm)
Use 4 pcs of M3 × 6 flat head Phillips screws to fix the router on the wall.
Recommended torque for mounting is 1.0 N·m, and the maximum allowed is 1.2 N·m.

7
3.3.2 DIN Rail Mounting (Measured in mm)
Use 2 pcs of M3 × 6 flat head Phillips screws to fix the mount clip to the router, and then hang the device
to the DIN rail. The width of DIN rail is 3.5cm.
Recommended torque for mounting is 1.0 N·m, and the maximum allowed is 1.2 N·m.

8
4. Log in the Web GUI of Router
4.1 PC Configuration
Please connect PC to LAN port of UR32L router. PC can obtain an IP address, or you can configure a
static IP address manually. The following steps are based on Windows 10 operating system for your
reference.
(Note: As remote access is disabled by default, you can't access to the router's Web GUI if you connect
PC to WAN port of the router. But it will function properly if you enable it on Web GUI.)
③Click “Ethernet” (May have different names). ④Click “Properties”.
①Click “Search Box” to search “Control Panel” on the
Windows 10 taskbar.
②Click “Control Panel” to open it, and then click
“View network status and tasks”.

9
(Note: Remember to click “OK” to finish configuration.)
4.2 Log in the Router
If this is the first time you configure the router, please use the default settings below:
IP Address: 192.168.1.1
Username: admin
Password: password
A. Start a Web browser on your PC (Chrome is recommended), type in the IP address, and press Enter on
your keyboard.
B. Enter the username and password, click “Login”.
⑤Double Click “Internet
Protocol Version 4 (TCP/IPv4)”
to configure IP address and
DNS server.
⑥Method 1: click “Obtain an IP
address automatically”;
Method 2: click “Use the
following IP address” to assign
a static IP manually within the
same subnet of the router.

10
If you enter the username or password incorrectly more than 5 times, the login page will be
locked for 10 minutes.
C. When you log in with the default username and password, you will be asked to modify the password.
It’s suggested that you change the password for the sake of security. Click “Cancel” button if you want to
modify it later.
D. After you log in the Web GUI, you can view system information and perform configuration on the
router.

11
5. Network Configuration
This chapter explains how to connect UR32L to network via WAN connection or cellular.
5.1 Ethernet WAN Configuration
A. Go to “Network > Interface > Port” to change LAN1 to WAN port.
B. Go to “Network > Interface > WAN” to configure WAN parameters. Take static IP configuration as an
example. DHCP client and PPPoE type are optional according to your requirements.
Click “Save & Apply” button to make the changes take effect.
C. Connect WAN port to another router or modem.
D. Log in UR32L web GUI via WAN port IP address and go to “Status > Network” to check if status is “up”.

12
E. Go to “Network > Interface > Link Failover” to rise the WAN priority to 1.
F. Open your preferred browser on PC, then type any available web address into address bar and see if it
is able to visit Internet via UR32L router.
5.2 Cellular Connection Configuration
A. Click “Network > Interface > Cellular > Cellular Setting” to configure the cellular info, like APN and
network type.
B. Click “Save” and “Apply” for configuration to take effect.
If you select “Auto”, the router will obtain ISP information from SIM card to set APN, Username, and
Password automatically. This option will only be taken effect when the SIM card is issued from a
well-known ISP.
C. Go to “Network > Interface > Link Failover” to enable SIM and rise link priority.

13
D. Click to configure ICMP ping detection information.
E. Click “Status > Cellular” to view the status of the cellular connection. If it shows “Connected”, it means
SIM has dialed up successfully.
On the other hand, you can check the status of SIM indicator. If it keeps on green light statically, it means
SIM has dialed up successfully.

14
F. Open your preferred browser on PC, then type any available web address into address bar and see if it
is able to visit Internet via UR32L router.
[END]

15
www.milesight-iot.com