Milwaukee M12 Fuel User manual

SPECIFICATIONS
Cat. No................................................................. M12 UCL
Light Output
High ............................................. 1,200 Lumens
Medium........................................... 800 Lumens
Low................................................. 600 Lumens
Battery Type .................................................... M12™
Charger Type................................................... M12™
DC Input Volts...................................................... 12V
Max DC Input Amps............................................ 0.8A
Recommended Ambient
Operating Temperature ............... -17°C to 51°C
WARNING
Always remove the battery pack any
ASSEMBLY
WARNING
Recharge o
ified for the battery
nly with the charg
. For specific
er spec-
charging instructions, read the operator’s manual
supplied with your charger and battery.
Inserting/Removing the Battery
To remove the battery, push in the release buttons and
pull the battery pack away from the tool.
M12™ UNDERCARRIAGE
LIGHT
Cat. No.: M12 UCL
time the tool is not in use.
To insert the battery, slide the pack into the body of the
tool. Make sure it latches securely into place.
IMPORTANT SAFETY INSTRUCTIONS
WARNING
READ
INSTRUCTIONS
AND
.
UNDERST
When using
AND
elec
ALL
-
tric appliances, basic precautions should always
be followed, including the following:
•
•
•Before using, read this operator’s manual, your battery
pack and charger operator’s manual, and all labels on
the battery pack, charger and light. Learn your light’s
applications and limitations as well as potential hazards
associated with this type of tool.
•Read and understand all the instructions before using
the appliance.
•To reduce the risk of injury, close supervision is nec-
essary when an appliance is used near children.
•Store idle light out of reach of children. Warm lights
can become hazardous in the hands of children.
•
•
•Store indoors. Do not expose to rain.
•Batteries must be recharged only with the charger
A charger that may be
when used with another battery.
pack.
When battery pack is not in use, keep it away from met-
al objects like: paper clips, coins, keys, nails, screws,
or other small metal objects that can make a connec-
tion from one terminal to another. Shorting the battery
Do not store light by the magnetic storage tray.
Remove light from undercarriage before operating a
vehicle. A light left attached to the undercarriage may
break free which could result in personal injury.
Maintain labels and nameplates. These carry
important information. If unreadable or missing, contact a
MILWAUKEE®service facility for a replacement.
SAVE THESE INSTRUCTIONS
FUNCTIONAL DESCRIPTION
2
3
4
6
7
5
8
5.
1. Fuel gauge
2. Mode button
3. Power button
4. Light head
6.
Light head handle
7. Magnetic base
8. Battery bay
1
SYMBOLOGY
Volts
Direct Current
Read Operator's Manual
Magnet
Pinch Hazard - Keep hands out of pinch zone
ADDITIONAL BATTERY SAFETY RULES
WARNING
WARNING
To reduce the risk of fire, personal
injury, and product damage due to
a short circuit, never immerse your tool, battery
pack or charger in fluid or allow a fluid to flow inside
them. Corrosive or conductive fluids, such as
seawater, certain industrial chemicals, and bleach
or bleach-containing products, etc., can cause a
short circuit.
Do not charge non-rechargeable
batteries.
Do not dispose of electric tools together
with household waste material. Electric
tools and electronic equipment that have
reached the end of their life must be
collected separately and returned to an
environmentally compatible recycling
facility.
Regulatory Compliance Mark (RCM). This
product meets applicable regulatory
requirements.
V
Class III protection
Do not stare at light source.
The product was only suitable for indoor
use. Never expose the product to rain.
Magnetic storage
tray

WARNING
MAINTENANCE
Maintain Light
WARNING
Use only recommended accessories.
Cleaning
Keep tool handles clean, dry and free of oil or grease. Use
only mild soap and a damp cloth to clean the tool, battery
pack and charger since certain cleaning agents and sol-
vents are harmful to plastics and other insulated parts.
Some of these include gasoline, turpentine, lacquer thin-
ner, paint thinner, chlorinated cleaning solvents, ammo-
nia and household detergents containing ammonia. Nev-
ACCESSORIES
Others may be hazardous.
To reduce the risk of injury,
alwaysunplug the charger and
remove the battery pack from the charger or tool
before performing any maintenance. Never
disassemble the tool, battery pack or charger.
Contact a MILWAUKEE® service facility for ALL
repairs.
Keep your light, battery pack and charger in good
repair by adopting a regular maintenance
program. If the light does not work properly,
return the light to a MILWAUKEE® service facility
for repairs.
For a complete listing of accessories, go online to
www.milwaukeetool.com.au /
www.milwaukeetool.co.nz or contact a distributor.
WARRANTY - AUSTRALIA and NEW ZEALAND
SERVICE - AUSTRALIA and NEW ZEALAND
MILWAUKEE®prides itself in producing a premium quality product that is Nothing But Heavy DutyTM.
Your satisfaction with our products is very important to us! If you encounter any problems with the
operation of this tool, please contact your authorised MILWAUKEE®dealer.
For a list of MILWAUKEE®dealers, guarantee or service agents please contact MILWAUKEE®
Customer Service or visit our website.
(Australia Toll Free Telephone Number 1300 645 928)
(New Zealand Toll Free Telephone Number 0800 645 928)
or visit milwaukeetool.com.au/milwaukeetool.co.nz.
Please refer to Australian and New Zealand warranty supplied with tool. This warranty applies only to
product sold by authorised dealers in Australia and New Zealand.
01614700301Q-01A
Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Tool (Australia)
21 Kelletts Road, Rowville, VIC 3178
Melbourne, Australia
Milwaukee Tool (New Zealand)
274 Church Street, Penrose,
Auckland, 1061, New Zealand
DESIGNED BY MILWAUKEE ELECTRIC TOOL CORP.
PROFESSIONALLY MADE IN CHINA
PRINTED IN CHINA
OPERATION
WARNING
To reduce the risk
look directly into the light when the
of injury, do not
light is on.
To turn on the light, press the Power button . Press
the MODE button to cycle through High, Medium and
Low settings. To turn the light, press the Power
button again.
Use the magnetic storage to store
nuts and bolts.
WARNING
The light source contained in this
luminaire shall only be replaced by
the manufacturer or his service agent or a similar
qualified person.