Miranda M848-2705-490 Datasheet

Vertigo XG
Advanced HD/SD Graphics Processor
Installation & Quick Start Guide
M848-2705-490
www.miranda.com

Copyright & Trademark Notice
Copyright © 2014, Miranda Technologies Partnership. All rights reserved.
Belden, Belden Sending All The Right Signals, and the Belden logo are trademarks or
registered trademarks of Belden Inc. or its affiliated companies in the United States and
other jurisdictions. Miranda, Vertigo XG are trademarks or registered trademarks of Miranda
Technologies Partnership. Belden Inc., Miranda Technologies Partnership, and other
parties may also have trademark rights in other terms used herein.
Terms and Conditions
Please read the following terms and conditions carefully. By using Vertigo XG
documentation, you agree to the following terms and conditions.
Miranda Technologies Partnership (“Miranda”) hereby grants permission and license to
owners of Vertigo XG to use their product manuals for their own internal business use.
Manuals for Miranda products may not be reproduced or transmitted in any form or by any
means, electronic or mechanical, including photocopying and recording, for any purpose
unless specifically authorized in writing by Miranda.
A Miranda manual may have been revised to reflect changes made to the product during its
manufacturing life. Thus, different versions of a manual may exist for any given product.
Care should be taken to ensure that one obtains the proper manual version for a specific
product serial number.
Information in this document is subject to change without notice and does not represent a
commitment on the part of Miranda.
Warranty Policies
Warranty information is available in the Support section of the Miranda Web site
(www.miranda.com).
Document Identification
Title Vertigo XG - Installation & Quick Start Guide
Part number M848-2705-490
SW version Vertigo Suite v.4.9

Revision History
After the original release date, this document may be updated with edits and then re-
released. The following table tracks the versions of this document.
Revision date Description
March 31, 2014 Original release

Safety Compliance
Electromagnetic Compatibility
This equipment complies with the requirements of the following standards for
Safety of Information Technology Equipment:
• CSA C22.2 no. 60950-1-07 (2
nd
Edition)
• UL 60950-1 (2
nd
Edition)
• IEC/EN 60950-1 (2
nd
Edition)
Warning: An appropriately listed/certified main supply power cord must be used for the
connection of the equipment to the main voltage at either 120V
~
or 240V
~
CAUTION: These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing than that
contained in the operating instructions unless you are qualified to do so. Refer all
servicing to qualified service personnel. Servicing should be done in a static-free
environment.
This equipment has been tested for verification of compliance with FCC Part 15,
Subpart B requirements for Class A digital devices.
N OTE
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC rules. These limits are designed
to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment
generates, uses and radiates radio frequency energy, and, if not installed and
used in accordance with the instruction manual, may cause harmful
interference in which case the user will be required to correct the interference
at his own expense.
This equipment has been tested and complies with the requirements of the
directive 2004/108/CE :
• EN 55022 Class A Radiated emissions
• EN 55022 Class A Conducted emissions
• EN 61000 -3-2 Harmonic current emission limits
• EN 61000 -3-3 Voltage fluctuation and flicker limitations
• EN 61000 -4-2 Electrostatic discharge immunity
• EN 61000 -4-3 Radiated EMF immunity-RF
• EN 61000 -4-4 Electrical fast transient immunity
• EN 61000 -4-5 Surge immunity
• EN 61000 -4-8 Power frequency magnetic field
• EN 61000 -4-11 Voltage dips, short interruption and voltage variation immunity

WARNING
Vertigo XG devices contain Class 1 lasers, which are deemed safe under normal
operating conditions.
Standalone Equipment - Laser source(s) employed:
CLASS 1 LASER PRODUCT
APPAREIL A LASER DE CLASSE 1
WARNING
Vertigo XG devices contain a Lithium battery in the service access area, which
should be replaced by the same type of battery.

Vertigo XG Installation & Quick Start Guide TOC-1
T ABLE OF C ONTENTS
Introduction .......................................................................................................................... 1-1
Vertigo XG product description.......................................................................................................... 1-2
Overview of the Vertigo XG chassis .................................................................................................. 1-4
Front panel components ............................................................................................................... 1-5
Rear panel components................................................................................................................ 1-6
Installation and quick start instructions ............................................................................ 2-1
Unpacking and verifying the Vertigo XG shipped items..................................................................... 2-3
Mounting the Vertigo XG chassis in a rack........................................................................................ 2-7
Cabling the Vertigo XG unit ............................................................................................................. 2-11
Starting the Vertigo XG.................................................................................................................... 2-14
Assigning a new IP address to the Vertigo XG device .................................................................... 2-16
Verifying the installation and setup by previewing the playout ........................................................ 2-17
Completing the quick start procedure.............................................................................................. 2-20
Need further assistance? .................................................................................................... 3-1

Vertigo XG Installation & Quick Start Guide 1-1
1 I NTRODUCTION
This guide provides basic Vertigo XG product information, as well as an orientation of its
hardware components. This guides also provides instructions for performing a first-time
installation of the Vertigo XG device, as well as initial setup tasks to get the device up and
running.
New Vertigo XG devices are factory configured for standard rendering and playout
workflows. Configuring the Vertigo XG settings for advanced workflows is normally
performed by qualified network administrators or Miranda’s Integration Specialists using the
Vertigo XG Portal and Dashboard software interfaces. Information and instructions for
implementing advanced configurations is beyond the scope of this document, but are
covered in the Vertigo XG Configuration Guide. Please visit the Miranda Support Portal
(http://www.miranda.com/support/index) for the latest documentation updates.

1-2 Vertigo XG Installation & Quick Start Guide
Introduction
Vertigo XG product description
The Vertigo XG is Miranda’s full-featured HD/SD graphics processor providing high
performance single or dual channel graphics rendering and video playback performance.
The Vertigo XG is ideal for a wide range of advanced real-time broadcast applications, like
HD/SD dual-casting with independent graphics for HD and SD, and single channel
applications demanding sophisticated, multi-channel branding and promotional graphics.
The Vertigo XG is available in two (2) standard models:
Both models of the Vertigo XG have the following features and capabilities:
• 3 RU rack mount chassis
• 2 video input channels
• 1 video output channel (XG21-e) or 2 video output channels (XG22-e)
• SD and HD video support
• 1 TB of video and audio storage, which is expandable to 2 TB
• 16 embedded audio channels per SDI stream
• Discrete AES audio channels - up to 8 in and 16 out (XG21-e) or 2 x 16 out (XG22-e)
• Independent DVEs on each video input
• Tri-mode hardware Video bypasses
• VAnc + VBI extraction processing and insertion or VAnc/VBI pass through
• Unlimited virtual layers that can be controlled independently
• Real-time control of live data sources with automatic on-air updates
• True Type/Unicode character support
• One seat of Xplay is included with each channel of the Vertigo XG purchased which
integrates the following features and functionality:
• Automation interface via RS-232, RS-422 (option) and TCP/IP
• Xplay’s graphical interface used for manual control of playlists
• “As run” logging
VX-Vertigo-XG21-e Vertigo XG single channel graphics engine (2 inputs, 1 output)
used for downstream branding.
VX-Vertigo-XG22-e Vertigo XG dual channel graphics engine (2 inputs, 2 outputs)
used for downstream simulcast branding.

Vertigo XG Installation & Quick Start Guide 1-3
Introduction
The following options are available to both models of the Vertigo XG:
VX-RS422-2-e 2 port RS-422 card
The RS-422 card provides an interface upon which the
Vertigo XG can communicate with automation systems.
VX-Audio-e Audio processor
The Audio option allows you play out audio clips and voice-
over tracks.
VX-EAS EAS Text Integration (EAS Plugin and EAS Software
Panel)
High quality EAS text and audio can be played out with the
Vertigo XG processor, using templates which integrate
channel branding graphics for a consistent on-air
presentation.
VX-GPI-8-e GPI card
The GPI card allows for control of the Vertigo XG via GPI
triggers. The card allows for up to 8 GPI in and 8 GPI out.
VX-TC-e Time Code card
The Time Code card allows you to lock the Vertigo XG’s
system clock to an external timecode.
VX-ClipPlayer Clip Player
The Clip Player is an internal codec package for playing out
multi-format video clips.
VX-2TB-UPG 1 TB RAID10 Expansion option (2 x 1TB)
Increases the usable storage from 1TB to 2TB.

1-4 Vertigo XG Installation & Quick Start Guide
Introduction
Overview of the Vertigo XG chassis
The Vertigo XG unit is a 3RU rackmount rendering platform that incorporates redundant fans,
two power supplies, and 1 TB RAID1-enabled storage (optional 2 TB RAID10 expansion).
The only visible difference between the two models of the Vertigo XG is that the single channel
model (XG21-e) has only one (1) discrete AES audio connector, while the dual channel model
(XG22-e) has two (2) discrete AES audio connectors.
In some cases, the positioning of the connectors on the Vertigo XG’s rear panel differs
depending upon the hardware options installed. See page 1-3 for a list of the Vertigo XG’s
hardware options.
The following table summarizes the Vertigo XG’s physical dimensions and power
consumption:
Consult the following sections to familiarize yourself with the Vertigo XG’s front and rear panel
components:
•“Front panel components” on page 1-5
•“Rear panel components” on page 1-6
Chassis F ORM : 3U rackmount chassis
H EIGHT : 5.2” (132 mm)
W
IDTH : 17.7” (450 mm)
D
EPTH : 25.5” (648 mm)
Power consumption AC input: 100 - 240V, 50 - 60 Hz
Consumption: 4.05 - 1.73A
Power: 410 max.
Temperature Ambient temperature: 35 C
Note: This shall be the maximum internal
temperature within the rack in which the
Vertigo XG unit is installed.
°