Miroir MP150A User manual

HD PROJECTOR MP150A

1
CONTENTS
Caution ...................................................................2
Warning! ..................................................................5
FCC Information...........................................................6
Location of Parts and Controls .............................................8
Specifications ............................................................10
Projector Compatibility ....................................................11
Cables and Adapters Included In the Box..............................11
Apple®Devices......................................................12
Other Devices.......................................................13
Charging the Battery .....................................................14
Operating the Projector ...................................................15
Setup...............................................................15
Powering Up and Viewing Media .....................................17
Image Adjustments ..................................................18
Charging with the Projector ...............................................20
Troubleshooting ..........................................................21
One (1) Year Limited Warranty ............................................23

2
CAUTION
• TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER. THERE ARE NO SERVICEABLE PARTS INSIDE
• TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
EXPOSE THIS UNIT TO RAIN OR MOISTURE.
The lightning flash with arrow-head symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the unit’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock
The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the unit.
IMPORTANT SAFETY INSTRUCTIONS
All of the safety and operating instructions should be read, adhered to and
followed before the unit is operated.
SAVE THESE INSTRUCTIONS!

3
DANGER
To reduce the risk of electric shock, burns, fire or injury:
1. Do not use while bathing or in a shower.
2. Do not place or store unit where it can fall or be pulled into a tub or sink.
3. Do not place in, drop or submerge in water or other liquid.
4. Do not reach for unit that has fallen into water. Unplug it immediately.
5. Care should be taken so that objects do not fall and liquids are not spilled onto
the unit.
WARNING
1. Close supervision is necessary when this appliance/product is used by or
near children or mentally disabled individuals.
2. Use this unit only for its intended use as described in this manual.
3. Unplug this unit during lightning storms or when unused for long periods
of time.
4. Never drop or insert an object into any opening.
5. Protect the adapter cord from being walked on or pinched, particularly at
plug outlets, convenience receptacles and the point where it exits the unit.
6. Do not allow adapter cord to touch hot surfaces. Wrap cord loosely

4
around the unit when storing.
7. The unit should be situated away from direct sunlight or heat sources
such as radiators, electric heaters, heat registers, stoves, or other units
(including amplifiers) that produce heat. Avoid placing on top of stereo
equipment that radiates heat.
8. Never block the air openings of the unit with materials such as clothing,
plastic bags or papers, or place it on a soft surface such as a bed or
couch, where the air openings may be blocked.
9. Do not overload electrical outlet. Use only the power source
as indicated.
10. Do not carry this unit by cord or use cord as handle.
11. Never operate this unit if it has a damaged cord or plug, if it is not
working properly, or if it has been dropped or damaged, or dropped into
water. If the unit’s power supply cord or plug is damaged, do not attempt
to fix it yourself.
12. To avoid the risk of electric shock, do not disassemble or attempt to
repair the unit. Incorrect repair can cause risk of electric shock or injury to
persons when unit is used.
13. Do not operate in the presence of explosive and/or flammable fumes.
14. Never remove the plug from the socket by pulling the power cord.

5
WARNING!
This producT conTains a rechargeable baTTery
•Do not store this product in high temperatures, damp areas, or in
direct sunlight.
•Never disassemble the product.
•Never dispose of the product in fire or water, which may result in
explosion and/or injury.
•Keep product out of reach of children.
•Do not touch product with damp hands.
•Dispose of the product properly.
•The product must not be discarded with ordinary household waste.
•Contact your local recycling center for proper disposal.

6
FCC INFORMATION
This device complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received including interference
that may cause undesired operation.
WARNING: Changes or modifications to this unit not expressly approved
by the party responsible for compliance could void the user’s authority to
operate the equipment. Note: This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This unit generates,
uses, and can radiate radio frequency energy and if not installed and used
in accordance with the instructions, may cause harmful interference to
radio communications. However, there is no guarantee that interference will

7
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try and correct
the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Shielded cables must be used with this unit to ensure compliance with the
Class B FCC limits.

8
LOCATION OF PARTS AND CONTROLS
1. Battery indicator lights
2. Focus wheel
3. Volume up control
4. Volume down control
5. Power button
6. 3.5mm Audio out
7. USB out (5V/1A)
8. Mode control
9. HDMI Input
10. DC input (12V/2A)
11. Reset Button
14
12 13
1
4
3
2
5
679 1110
8

9
LOCATION OF PARTS AND CONTROLS
12. Ambient light sensor
13. Lens
14. Tripod Dock
14
12 13
1
4
3
2
5
679 11108

10
SPECIFICATIONS
Product Dimensions 3.2” x 5.2” x 1”
Brightness 200 Lumens*
Lamp Life LED lamp with up to 20,000 hours
Image Size Up to 100”
Distance 2ft to 10ft
Throw Ratio 1.66
Contrast Ratio 400:1*
Native Resolution 1280 x 720 (720p)
Aspect Ratio 16:9
Built-in Speaker 2 1-watt speakers
Power DC 12V/2A
Auto Keystone +/- 40 degrees vertical keystone correction
Battery Li-polymer, 6,000 mAh
*TI’s DLP® IntelliBright™ technology dynamically adjusts the projector brightness range for each individual
pixel based on image content and the ambient room light level.

11
PROJECTOR COMPATIBILITY
Included in the box
Purchase separately
This symbol highlights devices that have the ability to
mirror the on screen content from your device with the
projector. Devices that do not support mirroring can still
project utilizing applications that support video out. For
example: Netflix™, Hulu®, and YouTube™ video services.
cables and adapTers included in The box
AC Adapter HDMI®to HDMI Cable Micro HDMI Adapter

12
apple®devices
iPhone®6 Plus
iPhone 6
iPhone 5s
iPhone 5c
iPhone 5
iPod touch®5
iPod touch 4
iPad Air
iPad®Mini
iPad 4
HDMI
Lightning™ Digital AV Adapter
HDMI to HDMI Cable
iPhone 4s
iPad 3
iPad 2
HDMI
30-Pin Digital AV Adapter
HDMI to HDMI Cable
iPhone 4
iPod touch 3

13
MacBook Pro®
with Retina display
Mac Mini
Mac Pro
Apple TV HDMI to HDMI Cable
MacBook Air®
MackBook Pro
iMac®Mini DisplayPort to HDMI Adapter
HDMI to HDMI Cable
oTher devices
GoPro
Micro HDMI Adapter
HDMI to HDMI Cable

14
CHARGING THE BATTERY
1. The built-in battery is charged using the included AC adapter.
IMPORTANT: Fully charge the battery before first use (approx. 4-5 hours).
2. The battery has 4 battery charge indicator lights. The lights will flash
in turn as the device charges. The battery is fully charged when all 4
lights are lit and no longer flash.
3. Check the battery life by briefing pushing the power button. The
indicator lights will illuminate indicating the amount of battery
remaining (for example, if 3 lights illuminate, there is approximately
75% of the battery life remaining).

15
OPERATING THE PROJECTOR
seTup
1. The projector can be powered using the included AC adapter or the
built-in battery.
•To power the projector with AC power, connect the AC adapter to
the projector’s DC input and plug the other end into an outlet. Once
connected, the battery indicator lights will illuminate on the projector
showing the amount of battery power remaining.
•To power the projector with the built-in battery, simply turn the projector
on. To check the remaining battery life of the projector press the power
button briefly.
IMPORTANT: Fully charge the battery before first use (approx. 4-5 hours).
2. Connect the included HDMI cable to the HDMI port on the projector
and the other end to your device.

16
NOTE: Some devices may require an adapter to connect to your device.
To determine what type of adapter you need to use, please reference the
Compatibility section of this manual, or our website at www.miroirusa.com.
3. If desired, connect a speaker to the 3.5mm audio out jack. If no
external speaker is connected, the projector’s 2 internal 1-watt
speakers will be used for audio.

17
powering up and viewing Media
IMPORTANT: Before you power on the projector, please be sure to check
that there is nothing blocking the ambient light sensor on the front of the
projector(the location of this sensor can be seen in Locations and Parts
diagram on page 9). Blocking this sensor may impact the IntelliBright
adjustments the projector makes which optimizes the projected image.
1. Power on the projector by pressing and holding the power button for
3 seconds.
2. Allow the projector 15 to 30 seconds to fully start up and make
image adjustments.
•When initially turned on, you will see the Miroir startup screen.
Following that screen, the screen may flicker briefly as DLP IntelliBright
technology built into the projector makes adjustments according to the
ambient light in your environment.
NOTE: After syncing with the projector you may see your device’s screen

18
being mirrored by the projector. Some devices may not have this ability,
but they can still be used with the projector to project videos, photo slide
shows, and some app content (this functionality is app dependent).
3. Choose the media you would like to view from the menu on your
device and play as you normally would.
iMage adjusTMenTs
ADJUSTING THE FOCUS
Simply roll the focus wheel control forwards and backwards to fine-tune
the projected image.
ADJUSTING THE VERTICAL KEYSTONE
Press the mode selection key and the projector will automatically adjust
the display screen to the best condition (+/- 40 degrees automatic vertical
keystone correction).