Mitsubishi Electric PUMY-P112VKM1 User manual

TECHNICAL & SERVICE MANUAL
OUTDOOR UNIT
No. OCH576
HFC
utilized
R410A
October 2014
Note:
• This service manual
describes technical data of
the outdoor units only.
<Outdoor unit>
[Model Name]
Model name
indication
PARTS CATALOG (OCB576)
PUMY-P112VKM1
PUMY-P125VKM1
PUMY-P140VKM1
PUMY-P112YKM1
PUMY-P125YKM1
PUMY-P140YKM1
PUMY-P112VKM1-BS
PUMY-P125VKM1-BS
PUMY-P140VKM1-BS
PUMY-P112YKM1-BS
PUMY-P125YKM1-BS
PUMY-P140YKM1-BS
Salt proof model
PUMY-P112VKM1
PUMY-P125VKM1
PUMY-P140VKM1
PUMY-P112YKM1
PUMY-P125YKM1
PUMY-P140YKM1
PUMY-P112VKM1-BS
PUMY-P125VKM1-BS
PUMY-P140VKM1-BS
PUMY-P112YKM1-BS
PUMY-P125YKM1-BS
PUMY-P140YKM1-BS
[Service Ref.]
CONTENTS
1. SAFETY PRECAUTION....................................2
2. OVERVIEW OF UNITS......................................5
3. SPECIFICATIONS.............................................9
4. DATA................................................................11
5. OUTLINES AND DIMENSIONS......................22
6. WIRING DIAGRAM.........................................24
7. NECESSARY CONDITIONS FOR SYSTEM CONSTRUCTION..... 26
8. TROUBLESHOOTING.................................... 42
9. ELECTRICAL WIRING...................................131
10. REFRIGERANT PIPING TASKS....................137
11. DISASSEMBLY PROCEDURE.......................144
SPLIT-TYPE, HEAT PUMP AIR CONDITIONERS

2
Cautions for units utilizing refrigerant R410A
1-1. CAUTIONS RELATED TO NEW REFRIGERANT
Use new refrigerant pipes.
Store the piping indoors, and both ends of the
piping sealed until just before brazing.
(Leave elbow joints, etc. in their packaging.)
Avoid using thin pipes.
Charge refrigerant from liquid phase of gas
cylinder.
If the refrigerant is charged from gas phase, composition
change may occur in refrigerant and the efficiency will be
lowered.
Do not use refrigerant other than R410A.
If other refrigerant (R22, etc.) is used, chlorine in refrige-
rant can cause deterioration of refrigerant oil, etc.
Use a vacuum pump with a reverse flow check
valve.
Vacuum pump oil may flow back into refrigerant cycle and
that can cause deterioration of refrigerant oil, etc.
Use the following tools specifically designed for
use with R410A refrigerant.
The following tools are necessary to use R410A refrigerant.
Handle tools with care.
If dirt, dust or moisture enters into refrigerant cycle, that can
cause deterioration of refrigerant oil or malfunction of com-
pressor.
Do not use a charging cylinder.
If a charging cylinder is used, the composition of refrigera-
nt will change and the efficiency will be lowered.
Flare tool
Electronic refrigerant
charging scale
Vacuum pump adaptor
Size adjustment gauge
Gauge manifold
Torque wrench
Gas leak detector
Charge hose
Tools for R410A
Contamination inside refrigerant piping can cause deterio-
ration of refrigerant oil, etc.
If dirt, dust or moisture enters into refrigerant cycle, that can
cause deterioration of refrigerant oil or malfunction of com-
pressor.
If large amount of mineral oil enters, that can cause deterio-
ration of refrigerant oil, etc.
Make sure that the inside and outside of refrige-
rant piping is clean and it has no contaminants
such as sulfur, oxides, dirt, shaving particles, etc,
which are hazard to refrigerant cycle.
In addition, use pipes with specified thickness.
The refrigerant oil applied to flare and flange
connections must be ester oil, ether oil or
alkylbenzene oil in a small amount.
Ventilate the room if refrigerant leaks during
operation. If refrigerant comes into contact with
a flame, poisonous gases will be released.
Use the specified refrigerant only.
Never use any refrigerant other than that specified.
Doing so may cause a burst, an explosion, or fire when the
unit is being used, serviced, or disposed of.
Correct refrigerant is specified in the manuals and on the
spec labels provided with our products.
We will not be held responsible for mechanical failure,
system malfunction, unit breakdown or accidents caused
by failure to follow the instructions.
1SAFETY PRECAUTION
OCH576

3
Gravimeter
Unit
[3] Service tools
Use the below service tools as exclusive tools for R410A refrigerant.
[1] Cautions for service
(1) Perform service after recovering the refrigerant left in unit completely.
(2) Do not release refrigerant in the air.
(3) After completing service, charge the cycle with specified amount of refrigerant.
(4) When performing service, install a filter drier simultaneously.
Be sure to use a filter drier for new refrigerant.
[2] Additional refrigerant charge
When charging directly from cylinder
· Check that cylinder for R410A on the market is a syphon type.
· Charging should be performed with the cylinder of syphon stood vertically. (Refrigerant is charged from liquid phase.)
Although "-BS" model has been designed to be resistant to salt damage, observe the following precautions to maintain the
performance of the unit.
1. Avoid installing the unit in a location where it will be exposed directly to seawater or sea breeze.
2. If the cover panel may become covered with salt, be sure to install the unit in a location where the salt will be washed away by
rainwater. (If a sunshade is installed, rainwater may not clean the panel.)
3. To ensure that water does not collect in the base of the outdoor unit, make sure that the base is level, not at angle. Water
collecting in the base of the outdoor unit could cause rust.
4. If the unit is installed in a coastal area, clean the unit with water regularly to remove any salt build-up.
5. If the unit is damaged during installation or maintenance, be sure to repair it.
6. Be sure to check the condition of the unit regularly.
7. Be sure to install the unit in a location with good drainage.
1-2. PRECAUTIONS FOR SALT PROOF TYPE "-BS" MODEL
No. Tool name Specifications
1Gauge manifold · Only for R410A
· Use the existing fitting specifications. (UNF1/2)
· Use high-tension side pressure of 5.3MPa·G or over.
2Charge hose · Only for R410A
· Use pressure performance of 5.09MPa·G or over.
3Electronic scale —
4Gas leak detector · Use the detector for R134a, R407C or R410A.
5Adaptor for reverse flow check · Attach on vacuum pump.
6Refrigerant charge base —
7Refrigerant cylinder · Only for R410A · Top of cylinder (Pink)
· Cylinder with syphon
8Refrigerant recovery equipment —
OCH576

4
Cautions for refrigerant piping work
New refrigerant R410A is adopted for replacement inverter series. Although the refrigerant piping work for R410A is same
as for R22, exclusive tools are necessary so as not to mix with different kind of refrigerant. Furthermore as the working
pressure of R410A is 1.6 times higher than that of R22, their sizes of flared sections and flare nuts are different.
1Thickness of pipes
Because the working pressure of R410A is higher compared to R22, be sure to use refrigerant piping with thickness
shown below. (Never use pipes of 0.7 mm or below.)
2Dimensions of flare cutting and flare nut
The component molecules in HFC refrigerant are smaller compared to conventional refrigerants. In addition to that,
R410A is a refrigerant, which has higher risk of leakage because its working pressure is higher than that of other refrig-
erants. Therefore, to enhance airtightness and strength, flare cutting dimension of copper pipe for R410A has been
specified separately from the dimensions for other refrigerants as shown below. The dimension B of flare nut for R410A
also has partly been changed to increase strength as shown below. Set copper pipe correctly referring to copper pipe
flaring dimensions for R410A below. For 1/2 and 5/8 inch pipes, the dimension B changes.
Use torque wrench corresponding to each dimension.
3Tools for R410A (The following table shows whether conventional tools can be used or not.)
1/4
3/8
1/2
5/8
3/4
6.35
9.52
12.70
15.88
19.05
0.8
0.8
0.8
1.0
—
0.8
0.8
0.8
1.0
1.0
Nominal
dimensions (in)
Diagram below: Piping diameter and thickness
Outside
diameter (mm)
Thickness (mm)
R410A R22
1/4
3/8
1/2
5/8
3/4
6.35
9.52
12.70
15.88
19.05
9.1
13.2
16.6
19.7
—
9.0
13.0
16.2
19.4
23.3
Nominal
dimensions (in)
Flare cutting dimensions
Outside
diameter Dimension A ( )
+0
-0.4 (mm)
R410A R22
(mm) 1/4
3/8
1/2
5/8
3/4
6.35
9.52
12.70
15.88
19.05
17.0
22.0
26.0
29.0
—
17.0
22.0
24.0
27.0
36.0
Nominal
dimensions (in)
Flare nut dimensions
Outside
diameter Dimension B (mm)
R410A R22
(mm)
Gauge manifold
Charge hose
Gas leak detector
Refrigerant recovery equipment
Refrigerant cylinder
Applied oil
Safety charger
Charge valve
Vacuum pump
Flare tool
Bender
Pipe cutter
Welder and nitrogen gas cylinder
Refrigerant charging scale
Vacuum gauge or thermis-
tor vacuum gauge and
vacuum valve
Charging cylinder
Air purge, refrigerant charge
and operation check
Gas leak check
Refrigerant recovery
Refrigerant charge
Apply to flared section
Prevent compressor malfunction
when charging refrigerant by
spraying liquid refrigerant
Prevent gas from blowing out
when detaching charge hose
Vacuum drying and air
purge
Flaring work of piping
Bend the pipes
Cut the pipes
Weld the pipes
Refrigerant charge
Check the degree of vacuum. (Vacuum
valve prevents back flow of oil and refri-
gerant to thermistor vacuum gauge)
Refrigerant charge
Tool exclusive for R410A
Tool exclusive for R410A
Tool for HFC refrigerant
Tool exclusive for R410A
Tool exclusive for R410A
Ester oil, ether oil and
alkylbenzene oil (minimum amount)
Tool exclusive for R410A
Tool exclusive for R410A
Tools for other refrigerants can
be used if equipped with adop-
ter for reverse flow check
Tools for other refrigerants
can be used by adjusting
flaring dimension
Tools for other refrigerants can be used
Tools for other refrigerants can be used
Tools for other refrigerants can be used
Tools for other refrigerants can be used
Tools for other refrigerants
can be used
Tool exclusive for R410A
Tools and materials Use R410A tools Can R22 tools be used?
(Usable if equipped
with adopter for rever-
se flow)
(Usable by adjusting
flaring dimension)
Can R407C tools be used?
Ester oil, ether oil:
Alkylbenzene oil: minimum amount
(Usable if equipped
with adopter for rever-
se flow)
(Usable by adjusting
flaring dimension)
: Prepare a new tool. (Use the new tool as the tool exclusive for R410A.)
: Tools for other refrigerants can be used under certain conditions.
: Tools for other refrigerants can be used.
Dimension A
Dimension B
OCH576

5
2
2-1. UNIT CONSTRUCTION
Remote
controller
Name
Model number
Functions
M-NET remote controller
PAR-F27MEA-E
• A handy remote controller for use in
conjunction
with the Melans centralized
management system.
• Addresses must be set.
• Addresses setting is not
necessary.
MA remote controller
PAR-21MAA, PAR-30/31MAA
PAR-W21MAA(when using PWFY)
Outdoor unit
Capacity Type 15 to Type 125
1 to 9 unit 50 to 130% of outdoor unit capacity *2 *3
Type 15 to Type 140
1 to 10 unit
Applicable
indoor unit
Number of units
Total system wide capacity
4HP 5HP 6HP
PUMY-P112VKM1(-BS)
PUMY-P112YKM1(-BS) PUMY-P125VKM1(-BS) PUMY-P125YKM1(-BS)
1 to 12 unit
PUMY-P140VKM1(-BS)
PUMY-P140YKM1(-BS)
Branching pipe
components Branch header (2 branches) Branch header (4 branches) Branch header (8 branches)
CMY-Y62-G-E CMY-Y64-G-E CMY-Y68-G-E
*1. PUMY is connectable to Fresh Air type indoor unit.
It is possible to connect 1 Fresh Air type indoor unit to 1 outdoor unit. (1:1 system)
Operating temperature range (outdoor temperature) for fresh air type indoor units differ from other indoor units.
Refer to "2-4-(3). Operating temperature range".
*2. When the indoor unit of Fresh Air type is connected with the outdoor unit, the maximum connectable total indoor unit capacity is 110% (100%
incaseofheatingbelow−5: [23˚F]).
*3. When connecting PWFY series
•Only1PWFY-P100VM-E-AUcanbeconnected.PWFY-P200VM-E-AUandPWFY-P100VM-E-BUcannotbeconnected.
•ThePWFYunitcannotbetheonlyunitconnectedtoanoutdoorunit.Selectanindoorunitsothatthetotalratedcapacityoftheindoor
units, excluding the PWFY unit, is 50 to 100% of the outdoor unit capacity.
*4.
WhenconnectingtheCONNECTIONKIT(PAC-LV11M-J)andanM-seriesindoorunit,refertotheinstallationmanualfortheCONNECTIONKIT.
Decorative panel
OVERVIEW OF UNITS
Model
Capacity
Cassette Ceiling Ceiling
Concealed Wall Mounted Ceiling Suspended Floor standing
Ceiling
Concealed
(FreshAir) *1
Air to Water
Unit *3
CONNECTION KIT
4-way ow 2-way ow 1-way ow Exposed Concealed
PAC-LV11M-J
PLFY-P PLFY-P PMFY-P PEFY-P PKFY-P PCFY-P PFFY-P PFFY-P
PEFY-P PWFY-P
15 - - - 15VMS1(L)-E 15VBM-E –
– – – –
20 20VCM-E(2)
20VLMD-E 20VBM-E
20VMS1(L)-E
/VMA(L)-E 20VBM-E –20VLEM-E
VKM-E(2) 20VLRM-E – –
25 25VCM-E(2)
25VLMD-E 25VBM-E
25VMS1(L)-E
/VMA(L)-E 25VBM-E –25VLEM-E
VKM-E(2) 25VLRM-E – –
32 32VCM-E(2)
32VBM-E
32VLMD-E 32VBM-E
32VMS1(L)-E
/VMA(L)-E 32VHM-E –32VLEM-E
VKM-E(2) 32VLRM-E – –
40 40VCM-E(2)
40VBM-E
40VLMD-E 40VBM-E
40VMS1(L)-E
/VMA(L)-E/VMH-E
40VHM-E 40VKM-E 40VLEM-E
VKM-E(2) 40VLRM-E – –
M series indoor unit *4
50 50VBM-E
50VLMD-E
–50VMS1(L)-E
/VMA(L)-E/VMH-E
50VHM-E –50VLEM-E 50VLRM-E – –
MSZ-GF Series
MSZ-SF Series
MSZ-EF Series
MSZ-FH Series
MFZ-KJSeries
63 63VBM-E
63VLMD-E –63VMS1(L)-E
/VMA(L)-E/VMH-E
63VKM-E 63VKM-E 63VLEM-E 63VLRM-E – –
71 –
– –71VMA(L)-E
/VMH – – –– – –
80 80VBM-E
80VLMD-E –80VMH-E
/VMA(L)-E – – ––80VMH-E-F –
100 100VBM-E
100VLMD-E –100VMH-E
/VMA(L)-E 100VKM-E 100VKM-E –
– –100VM-E-AU
125 125VBM-E
125VLMD-E –125VMH-E
/VMA(L)-E –125VKM-E –
– – –
140 – – – 140VMH-E
/VMA(L)-E –––
– 140VMH-E-F –
M series remote controller
OCH576

6
PUMY-P125VKM1(-BS)
PUMY-P125YKM1(-BS) PUMY-P140VKM1(-BS) PUMY-P140YKM1(-BS)
6HP
PUMY-P112VKM1(-BS)
PUMY-P112YKM1(-BS)
4HP
Applicable
indoor unit
Branch box
that can be
connected
Capacity
Number of units
Total system wide capacity
Type 15 to Type 100
2 to 8 units
1 to 2 units
24 to 130 % of outdoor unit capacity
(3.0 to 16.2 kW)
Number of units
Outdoor unit
Ceiling
concealed
4-way
ceiling cassette
Wall
mounted
Model type Model name
Deluxe
Standard
Compact
Low static pressure
Middle static pressure
2 by 2 type
Standard
MSZ-FH25/35/50VE
MSZ-SF25/35/42/50VE
MSZ-GF60/71VE
MSZ-EF18/22/25/35/42/50VE
MSZ-SF15/20VA
SEZ-KD25/35/50/60/71VA(L)
PEAD-RP50/60/71/100JA(L)Q.UK
SLZ-KA25/35/50VA(L)
PLA-ZRP35/50/60/71/100BA.UK
PCA-RP35/50/60/71/100KAQ
MFZ-KJ25/35/50VE
MLZ-KA25/35/50VA
Floor standing
Capacity class (kW)
2.2 2.5 3.5 5.0 6.0 7.1 8.0 10.0
Connectable indoor unit lineup (Heat pump inverter type)
Note: The lineup of a connectable indoor unit depends on a district/areas/country.
Branch box PAC-MK50BC
5 branches
(MAX. 5 units)
PAC-MK30BC
3 branches
(MAX. 3 units)
Number of branches
Indoor unit that
can be connected
( )
Note: A maximum of 2 branch boxes can be connected to 1 outdoor unit.
Select a model according to the connection method.
2- branch pipe (joint): Optional parts
In case of using 1- branch box
In case of using 2- branch boxes
No need
Model name Connection method
flare
brazing
MSDD-50AR-E
MSDD-50BR-E
Option Optional accessories of indoor units and outdoor units are available.
2.01.5 1.8 4.2
1-way ceiling cassette
5HP
21 to 130 % of outdoor unit capacity
(3.0 to 18.2 kW) 19 to 130 % of outdoor unit capacity
(3.0 to 20.2 kW)
Ceiling suspended
2-2. UNIT CONSTRUCTION (BRANCH BOX SYSTEM)
OCH576

7
PUMY-P125VKM1(-BS)
PUMY-P125YKM1(-BS) PUMY-P140VKM1(-BS) PUMY-P140YKM1(-BS)
Via branch box Citymulti indoor
PUMY-P112VKM1(-BS)
PUMY-P112YKM1(-BS)
Applicable
indoor unit
Capacity
Number
of units
Type 15 to Type 125
Via branch box Citymulti indoor
5
7 or 8*1
Outdoor unit
PAC-MK50BC
5 branches
(MAX. 5 units)
PAC-MK30BC
3 branches
(MAX. 3 units)
Brabch box
Number of branches
City multi indoor unit
Via branch box Type 15 to Type 140
Type 15 to Type 100
1-branch box
2-branch box
Via branch box Citymulti indoor
5
3 or 2*15
85 35 85
3
Total system wide capacity 6.3 to 16.2 kW 7.1 to 18.2 kW 8.0 to 20.2 kW
50 to 130% of outdoor unit capacity
Branching pipe
components
CMY-Y62-G-E
Branch header
(2 branches)
CMY-Y64-G-E
Branch header
(4 branches)
CMY-Y68-G-E
Branch header
(8 branches)
Citymulti indoor units*2
CONNECTION KIT
PAC-LV11M-J
M series indoor unit
M-NET
remote
controller
MA
remote
controller
M series
remote
controller
M series
S series
P series
indoor units*2
M-NET
remote
controller
MA
remote
controller
*1When connecting 7 indoor units via branch box, connectable citymulti
indoor units are 3; connecting 8 indoor units via branch box, connectable
citymulti indoor units are 2.
*2Refer to “2-1. UNIT CONSTRUCTION”, for more detail.
2-3. UNIT CONSTRUCTION (MIXED SYSTEM)
OCH576

8
2-4. UNIT SPECIFICATIONS
(2) Method for identifying MULTI-S model
(1) Outdoor Unit
Indoor unit < When using Model 80 > Outdoor unit <When using model 125 >
P L F Y - P 80 V BM - E PU M Y - P 125 Y K M 1 - BS
PAC type
BM
CM
KM
M
KM
LMD
Frequency
conversion
controller
Refrigerant
R407C/R22
R410A
commonness
Refrigerant
R410A
NEW frequency converter
one-to-many air conditioners
(flexible design type)
Indicates equivalent
to Cooling capacity
Indicates equivalent
to Cooling capacity
Power supply
V: Single phase
220/230/240 V, 50 Hz
Power supply
V: Single phase
220/230/240 V, 50 Hz
Y: 3-phase
380/400/415 V, 50 Hz
L : Ceiling cassette
K : Wall-mounted type
E : Hidden skylight type
C: Ceiling suspended type
M: Ceiling cassette type
F : Floor standing type
W:Air to Water Unit
M-NET
control
Outdoor unit
model type
Sub-number
M-NET
control
Frequency
conversion
controller
Outdoor unit
MULTI-S
(k cal/ h)
(k cal / h)
Salt proof
type
sub
number
Service Ref.
Capacity Cooling (kW)
Heating (kW) 12.5
14.0
2.9
14.0
16.0
3.5
15.5
18.0
3.9
Compressor (kW)
PUMY-P112VKM1(-BS)
PUMY-P112YKM1(-BS) PUMY-P125VKM1(-BS) PUMY-P125YKM1(-BS) PUMY-P140VKM1(-BS) PUMY-P140YKM1(-BS)
Cooling/Heating capacity indicates the maximum value at operation under the following condition.
*Cooling Indoor : D.B. 27 °C/ W.B. 19.0 °C
Outdoor : D.B. 35 °C
Heating Indoor : D.B. 20 °C
Outdoor : D.B. 7 °C/ W.B. 6 °C
(3) Operating temperature range
Notes: D.B. : Dry Bulb Temperature
W.B. : Wet Bulb Temperature
*110to46°CD.B.:WhenconnectingPKFY-P15/P20/P25VBM,PFFY-P20/25/32VKMandPFFY-P20/25/32VLE(R)Mtypeindoorunit.
Cooling
W.B. 15 to 24°C
D.B. −5 to 46°C*1
Heating
D.B. 15 to 27°C
W.B. −20 to 15°C
Indoor-side intake air temperature
Outdoor-side intake air temperature
■
When connecting fresh air type indoor unit
air type indoor
Capacity of Fresh
Cooling Heating
Indoor-side and Outdoor-side P80 D.B. 21 to 43:*2
W.B. 15.5 to 35:D.B.−10 to 20:*3
intake air temperature P140 D.B. 21 to 43 :*2
W.B. 15.5 to 35 :D.B. −5 to 20 :*3
*2 Thermo-OFF (FAN-mode) automatically starts if the outdoor temp. is lower than 21 : D.B..
*3 Thermo-OFF (FAN-mode) automatically starts if the outdoor temp. is higher than 20 : D.B..
■When connecting Air to Water Unit
Cooling Heating
Indoor-side intake water temperature
Outdoor-side intake air temperature
• PWFY series can operate in Heating mode but not in Cooling mode. An indoor unit other than that of PWFY series can
operate in Cooling mode.
• A PWFY series and other series cannot operate simultaneously.
• The operation of PWFY series takes precedence over other series. While a PWFY series is operating, other series do not operate.
• The set temperature on the remote controller represents the target temperature of the outlet water.
*4
*4D.B. 10 to 45 :
*4W.B. −20 to 15 :
OCH576

9
3SPECIFICATIONS
Model PUMY-P112VKM1(-BS) PUMY-P125VKM1(-BS) PUMY-P140VKM1(-BS)
Power source 1-phase 220/240 V,50Hz
Cooling capacity
(Nominal) kW*112.5 14.0 15.5
kcal/h*110,750 12,040 13,330
BTU/h*142,650 47,768 52,886
Power input kW 2.79 3.46 4.52
Current input A 12.87/ 12.32/ 11.80 15.97/ 15.27/ 14.64 20.86/ 19.95/ 19.12
COP kW/kW 4.48 4.05 3.43
Temp. range of
cooling Indoor temp. W.B. 15 to 24 °C
Outdoor temp. D.B. −5to46°C
Heating capacity
(Nominal) kW*214.0 16.0 18.0
kcal/h*212,040 13,760 15,480
BTU/h*247,768 54,592 61,416
Power input kW 3.04 3.74 4.47
Current input A 14.03/ 13.42/ 12.86 17.26/ 16.51/ 15.82 20.63/ 19.73/ 18.91
COP kW/kW 4.61 4.28 4.03
Temp. range of
heating Indoor temp. D.B. 15 to 27 °C
Outdoor temp. W.B. −20to15°C
Indoor unit
connectable Total capacity 50 to 130% of outdoor unit capacity
Model / Quantity Citymulti 15 - 125/ 9 15 - 140/ 10 15 - 140/ 12
Branch box 15 - 100/ 8 15 - 100/ 8 15 - 100/ 8
Mixed system
15 - 125(*3)/ 10 15 - 140/ 10*415 - 125/ 10*4
Sound pressure level
(measured in anechoic room) dB <A> 49/ 51 50/ 52 51/ 53
Power pressure level
(measured in anechoic room) dB <A> - - -
Refrigerant
piping diameter Liquid pipe mm (in) 9.52 (3/8)
Gas pipe mm (in) 15.88 (5/8)
FAN *2 Type x Quantity Propeller Fan x 2
Airowrate m3/min 110
L/s 1,833
cfm 3,884
Control, Driving mechanism DC control
Motor output kW 0.06+0.06
External static press. 0
Compressor Type x Quantity Scroll hermetic compressor x 1
Manufacture Mitsubishi Electric Corporation
Starting method Inverter
Capacity control % Cooling 26 to 100
Heating 20 to 100 Cooling 24 to 00 Heating 18 to 100 Cooling 21 to 100 Heating 17 to 100
Motor output kW 2.9 3.5 3.9
Case heater kW 0
Lubricant FV50S(2.3litter)
Externalnish Galvanized Steel Sheet
Munsell No. 3Y 7.8/1.1
External dimension HxWxD mm 1,338 x 1,050 x 330(+25)
in 52-11/16 x 41-11/ 32 x 13 (+1)
Protection
devices High pressure protection High pressure Switch
Inverter circuit (COMP./FAN) Overcurrent detection, Overheat detection(Heat sink thermistor)
Compressor Compressor thermistor, Over current detection
Fan motor Overheating,Voltageprotection
Refrigerant Type x original charge R410A 4.8kg
Control ElectronicExpansionValve
Net weight kg (lb) 123 (271)
Heat exchanger Cross Fin and Copper tube
HIC circuit (HIC: Heat Inter-Changer) HIC circuit
Defrosting method Reversed refrigerant circuit
Drawing External BK01N346
Wiring BH78B813
Standard
attachment Document Installation Manual
Accessory Grounded lead wire x2
Optional parts Joint:CMY-Y62-G-E
Header: CMY-Y64/68-G-E
Branch box: PAC-MK30/50BC
Remarks Unit converter
kcal/h = kW × 860
BTU/h = kW × 3,412
cfm = m3/min x 35.31
lb = kg/0.4536
Abovespecicationdatais
subject to rounding
variation.
*1Nominal cooling conditions *2Nominal heating conditions
Indoor :
27 °C D.B./19 °C W.B. [81 °F D.B/66 °FW.B.] 20 °C D.B. [68 °FD.B.]
Outdoor : 35 °C D.B. [95 °FD.B.]
7°C DB/6°C W.B. [45 °F D.B./43 °FW.B.]
Pipe length : 7.5m[24-9/16ft] 7.5m[24-9/16ft]
Level difference : 0m[0ft] 0m[0ft]
Note : 1. Nominal conditions *1, *2are subject to ISO 15042.
 2.Duetocontinuingimprovement,abovespecicationsmaybesubjecttochangewithoutnotice.
*3 Up to P100 when connecting via branch box.
*4 Up to 11 units when connecting via 2 branch boxes.
OCH576

10
Model PUMY-P112YKM1(-BS) PUMY-P125YKM1(-BS) PUMY-P140YKM1(-BS)
Power source 3-phase380–415V,50Hz
Cooling capacity
(Nominal) kW *112.5 14.0 15.5
kcal/h *110,750 12,040 13,330
BTU/h *142,650 47,768 52,886
Power input kW 2.79 3.46 4.52
Current input A 4.46/ 4.24/ 4.09 5.53/ 5.26/ 5.07 7.23/ 6.87/ 6.62
COP kW/kW 4.48 4.05 3.43
Temp. range of
cooling Indoor temp. W.B. 15 to 24°C
Outdoor temp. D.B. −5to46°C
Heating capacity
(Nominal) kW *214.0 16.0 18.0
kcal/h *212,040 13,760 15,480
BTU/h *247,768 54,592 61,416
Power input kW 3.04 3.74 4.47
Current input A 4.86/ 4.62/ 4.45 5.98/ 5.68/ 5.48 7.15/ 6.79/ 6.55
COP kW/kW 4.61 4.28 4.03
Temp. range of
heating Indoor temp. D.B. 15 to 27°C
Outdoor temp. W.B. −20to15°C
Indoor unit
connectable Total capacity 50 to 130% of outdoor unit capacity
Model / Quantity Citymulti 15 - 125 /9 15 - 140 /10 15 - 140 /12
Branch box 15 - 100/ 8 15 - 100/ 8 15 - 100/ 8
Mixed system 15 - 125(*3)/ 10 15 - 140/ 10*415 - 125/ 10*4
Sound pressure level
(measured in anechoic room) dB <A> 49/ 51 50/ 52 51/ 53
Power pressure level
(measured in anechoic room) dB <A> - - -
Refrigerant
piping diameter Liquid pipe mm (in) 9.52 (3/8)
Gas pipe mm (in) 15.88 (5/8)
FAN *2 Type x Quantity Propeller Fan x 2
Airowrate m3/min 110
L/s 1,833
cfm 3,884
Control, Driving mechanism DC control
Motor output kW 0.06+0.06
External static press. 0
Compressor Type x Quantity Scroll hermetic compressor x 1
Manufacture Mitsubishi Electric Corporation
Starting method Inverter
Capacity control % Cooling 26 to 100
Heating 20 to 100 Cooling 24 to100 Heating 18 to 100 Cooling 21 to 100 Heating 17 to 100
Motor output kW 2.9 3.5 3.9
Case heater kW 0
Lubricant FV50S(2.3litter)
Externalnish Galvanized Steel Sheet
Munsell No. 3Y 7.8/1.1
External dimension HxWxD mm 1338 x 1050 x 330(+25)
in 52-11/16 x 41-11/32 x 13 (+1)
Protection
devices High pressure protection High pressure Switch
Inverter circuit (COMP./FAN) Overcurrent detection, Overheat detection(Heat sink thermistor)
Compressor Compressor thermistor, Over current detection
Fan motor Overheating,Voltageprotection
Refrigerant Type x original charge R410A 4.8kg
Control ElectronicExpansionValve
Net weight kg (lb) 125 (276)
Heat exchanger Cross Fin and Copper tube
HIC circuit (HIC: Heat Inter-Changer) HIC circuit
Defrosting method Reversed refrigerant circuit
Drawing External BK01N339
Wiring BH78B814
Standard
attachment Document Installation Manual
Accessory Grounded lead wire x2
Optional parts Joint:CMY-Y62-G-E
Header: CMY-Y64/68-G-E
Branch box: PAC-MK30/50BC
Remarks: Unit converter
kcal/h = kW × 860
BTU/h = kW × 3,412
cfm = m3/min x 35.31
lb = kg/0.4536
Abovespecicationdatais
subject to rounding
variation
.
*1Nominal cooling conditions *2Nominal heating conditions
Indoor :
27 °C D.B./19 °C W.B. [81 °F D.B/66 °FW.B.] 20 °C D.B. [68 °FD.B.]
Outdoor : 35 °C D.B. [95 °FD.B.]
7°C DB/6°C W.B. [45 °F D.B./43 °FW.B.]
Pipe length : 7.5m[24-9/16ft] 7.5m[24-9/16ft]
Level difference : 0m[0ft] 0m[0ft]
Note : 1. Nominal conditions *1, *2are subject to ISO 15042.
 2.Duetocontinuingimprovement,abovespecicationsmaybesubjecttochangewithoutnotice.
*3 Up to P100 when connecting via branch box.
*4 Up to 11 units when connecting via 2 branch boxes.
OCH576