Mitsubishi Electric MELSEC iQ-F Series Instruction Manual

FACTORY AUTOMATION
Quick Connection Guide
FREQROL-A800/F800/E800 Series
for CC-Link IE Field Network Basic
Mitsubishi Electric Programmable Controller
MELSEC iQ-F Series

1
INTRODUCTION
Thank you for purchasing the Mitsubishi Electric MELSEC iQ-F series programmable controllers.
This manual describes the communication settings with inverters using the CC-Link IE Field Network Basic function of the
FX5 CPU module.
Before using this product, please read this manual and the relevant manuals carefully and develop familiarity with the
specifications to handle the product correctly.
When applying the program examples provided in this manual to an actual system, ensure the applicability and confirm that it
will not cause system control problems.
Regarding use of this product
• This product has been manufactured as a general-purpose part for general industries, and has not been designed or
manufactured to be incorporated in a device or system used in purposes related to human life.
• Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger
movement vehicles, please contact Mitsubishi Electric sales office.
• This product has been manufactured under strict quality control. However when installing the product where major
accidents or losses could occur if the product fails, install appropriate backup or failsafe functions into the system.
Note
• If in doubt at any stage during the installation of the product, always consult a professional electrical engineer who is
qualified and trained to the local and national standards. If in doubt about the operation or use, please contact your local
Mitsubishi Electric representative.
• Mitsubishi Electric will not accept responsibility for actual use of the product based on these illustrative examples. Please
use it after confirming the function and safety of the equipment and system.
• The content, specifications etc. of this manual may be changed, for improvement, without notice.
• The information in this manual has been carefully checked and is believed to be accurate; however, if you notice a doubtful
point, an error, etc., please contact your local Mitsubishi Electric representative. When doing so, please provide the manual
number given at the end of this manual.
Introduction for the concept and features of e-Manual Viewer is available on the following website.
http://fa-mel.com/fa/ref/ref.html?k=plceng&smerit=emaviewer_win
The installation file for Windowscan be downloaded from the following website.
http://fa-mel.com/fa/ref/ref.html?k=plceng&software=emaviewer_en
e-Manual Viewer
Quick and satisfying browsing
e-Manual Viewer allows users to browse optimized FA-related documents
such as Mitsubishi Electric FA product manuals.
e-Manual Viewer can be downloaded for free from
the Mitsubishi Electric FA website.
All necessary documents can be easily downloaded with one
click. The latest documents are available at any time.
Example programs contained in a document can be directly copied to
an engineering tool, eliminating the need of inputting the programs.
Easy on-demand download of latest documents
Refine search and fuzzy search are available for
all downloaded documents.
Quick cross document search for
necessary information
Copying example programs to
an engineering tool
The documents can be customized by adding useful information
as a note freely.
Sharing information among multiple users
Intuitive search using illustrations is available for
hardware specifications of the product.
Latest documents and notes can be shared with multiple users
using the document sharing function.

2
CONTENTS
CONTENTS
INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
RELEVANT MANUALS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
KEY FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
CHAPTER 1 PREPARATION 5
1.1 Applicable Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.2 Operation Flow Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1.3 Required Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
1.4 System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
CHAPTER 2 INVERTER SETTINGS 8
2.1 Names of the Parts on the Operation Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.2 List of Related Parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.3 Ethernet Parameter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.4 Parameter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
2.5 Writing Data to the Inverters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
2.6 Inverter Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
CHAPTER 3 PROGRAMMABLE CONTROLLER SETTINGS 17
3.1 Part Names. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.2 Downloading the FB Library. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
3.3 Importing the FB Library. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
3.4 Parameter Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
3.5 Adding Global Labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
3.6 Communication Settings of GX Works3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
3.7 Writing Data to the Programmable Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
CHAPTER 4 COUMMUNICATION CHECK OVER CC-Link IE Field Network Basic 32
CHAPTER 5 EXAMPLE PROGRAMS 33
5.1 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
5.2 How to Use the FB Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
5.3 Example Programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
5.4 Operation Check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
CHAPTER 6 TROUBLESHOOTING 43
6.1 Checking Procedure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
6.2 Checking the Programmable Controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
6.3 Checking the Inverters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
APPENDICES 47
Appendix 1 Example Applications of the FB Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Appendix 2 How to Use the Program Copy Function of e-Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Appendix 3 Downloading and Registering a Profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Appendix 4 Supplementary Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
REVISIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
WARRANTY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
SAFETY PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58
TRADEMARKS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58

3
RELEVANT MANUALS
The following relevant manuals can be downloaded from the Mitsubishi Electric FA site.
https://www.mitsubishielectric.co.jp/fa/ref/ref.html?kisyu=plcf&manual=download_all
[: Available, : Not available]
Manual name
<manual number>
Available form
e-Manual PDF
MELSEC iQ-F FX5U User's Manual (Hardware)
<JY997D55301>

MELSEC iQ-F FX5UC User's Manual (Hardware)
<JY997D61401>

MELSEC iQ-F FX5UJ User's Manual (Hardware)
<SH-082206ENG>

MELSEC iQ-F FX5 User's Manual (Application)
<JY997D55401>

MELSEC iQ-F FX5 User's Manual (Ethernet Communication)
<JY997D56201>

CC-Link IE Field Network Basic Reference Manual
<SH-081684ENG>

FB Library Reference Manual for CC-Link IE Field Network Basic Compatible Inverters
<FBM-1065/1066>

GX Works3 Operating Manual
<SH-081215ENG>

Programmable Controller Engineering Software MELSOFT GX Works3 FB Quick Start Guide
<L-08475ENG>

FR Configurator2 Instruction Manual
<IB-0600516ENG>

E800-E Inverter Safety Guideline
<IB-0600860ENG>

FR-E800 Instruction Manual (Connection)
<IB-0600865ENG>

FR-E800 Instruction Manual (Function)
<IB-0600868ENG>

FR-E800 Instruction Manual (Communication)
<IB-0600871ENG>

FR-E800 Instruction Manual (Maintenance)
<IB-0600874ENG>

FR-A800 Instruction Manual (Detailed)
<IB-0600503ENG>

FR-F800 Instruction Manual (Detailed)
<IB-0600547ENG>

A800-E / F800-E Ethernet Function Manual
<IB-0600628ENG>


4
KEY FEATURES
*1 FB libraries can be downloaded for free from the Mitsubishi Electric FA website.
https://www.mitsubishielectric.co.jp/fa/ref/ref.html?kisyu=plcf&samplelibrary=download_all
*2 Number of connectable inverters differs depending on firmware version.
Easy programming using FB library*1
FB (function block) library is a collection of FBs that are used in GX Works3. Various programs required to operate the
MELSEC iQ-F series modules can be designed easily by dragging and dropping FBs from the FB library to a program editor
and inputting devices, drastically reducing the cost and time required for programming.
Easy system construction Easy inverter setting using FR Configurator2
Using the CC-Link IE Field Network Basic function equipped
in the FX5 CPU module eliminates the need of extension
devices. Parameter settings can be easier because the
entire setting is performed on GX Works3 and automatically
detected inverter station information via Ethernet is reflected
to corresponding parameters.
Operations from startup to maintenance of inverters can be
easily performed on a personal computer by using FR
Configurator2. Various convenient functions of FR
Configurator2 support every phase such as design,
operation, and maintenance.
Converting
ladder blocks
into components
(FBs)
Converting
ladder blocks
into components
(FBs)
Converting
ladder blocks
into components
(FBs) FB
Command
FB
Monitoring
FB
Stopping
the inverter
FX5 CPU module
Hub
Inverter Inverter Inverter
Built-in
CC-Link IE
Field Network
Basic function
Built-in
CC-Link IE
Field Network
Basic function
Built-in
CC-Link IE
Field Network
Basic function
Inverter
Hub
Maximum Number of connectable
inverters to the FX5UJ:
8
FX5
CPU module
Inverter
Inverter
Maximum Number of connectable
inverters to the FX5U/FX5UC:
16
*2
Setting values in
the parameter list
and writing them
all in a batch.
Setting values in
the parameter list
and writing them
all in a batch.
Setting values in
the parameter list
and writing them
all in a batch.
Automatically
detecting inverters
connected to
a personal computer.
Automatically
detecting inverters
connected to
a personal computer.
Automatically
detecting inverters
connected to
a personal computer.

51 PREPARATION
1.1 Applicable Models
1PREPARATION
1.1 Applicable Models
The models described in this guide are shown in the following table.
1.2 Operation Flow Diagram
Programmable controller Inverter (Ethernet model)
FX5U CPU module FX5UC CPU module FX5UJ CPU module FR-E800-E FR-A800-E FR-F800-E
1. Preparing the required products 2. INVERTER SETTINGS 3. PROGRAMMABLE CONTROLLER
SETTINGS
4. Checking the communication
status
5. Program examples and checking the operation
Ethernet
FR Configurator2
Ethernet
Ethernet
Execution
command
Execution status
Normal end
Failed end
Execution
command
Error code
Executingresult
M290
M280
M_INVERTER_CC_IEF_Basic_ExecuteCommandCode_F_00A_1
ExecuteCommandCode
o_bENO:BB:i_bEN
Execution statusExecution command
M291
D0
Station number
Instruction code
Write value
o_bOK:BW:i_wStationNo
Normal end
M292
o_bErr:B
Failed end
o_wErrID:W
Error code
Station number
D280 W:i_wCommandCode
Instruction code
D281 W:i_wWriteValue
Write value
D290
o_wResultData:W
Executing result
D291
END
Operation
mode
write
Normal end
Execution command
Operation
mode
read
D280H0FBMOV
Instruction code
X25
D281K2MOV
Operation mode
M280
X24
When X24 is OFF, the instruction code H0FB is sent at the rising edge of X25 and the operation mode is changed to 2 (PU mode).
ExecuteCommandCode FB of the station number 1: Sending the instruction code to the station number 1
M291
RST
M280SET

1 PREPARATION
1.3 Required Products 6
1
1.3 Required Products
In a system configuration example of this manual, two inverters (FR-E800-E) are connected to the FX5U CPU module.
*1 A repeater hub cannot be used.
FX5U CPU module FR-E800-E × 2 Personal computer and software
Use an FX5U CPU module that meets the following
conditions.
• Serial number: 17X**** or later
• Firmware version: 1.110 or later
The PU port can be found when the front cover is
removed.
■FR-E800-E models
• FR-E820-EPA/EPB
• FR-E840-EPA/EPB
• FR-E860-EPA/EPB
GX Works3
• Supported software version: 1.050C or later
FR Configurator2
• Supported software version: 1.19V or later
Ethernet cable × 4 Hub
Use Ethernet cables compliant with the following standards.
• Category 5 or higher straight cable (double shielded / STP)
• IEEE 802.3 (100BASE-TX)
• ANSI/TIA/EIA-568-B (Category 5)
Use a hub that meets the following conditions.
• Compliance with the IEEE 802.3 (100BASE-TX)
• Equipped with the auto MDI/MDI-X function
• Equipped with the auto-negotiation function
• Switching hub (layer 2 switch)*1
First inverter
(Station number 1)
Second inverter
(Station number 2)

71 PREPARATION
1.4 System Configuration
1.4 System Configuration
This section describes the system configuration in which two inverters (FR-E800-E) are connected to the FX5U CPU module.
The inverters are connected into a star type using a switching hub and standard Ethernet cables.
When multiple inverters communicate with each other in a same network, the first three values of the IP addresses (first to
third octets) need to be the same. Assign IP addresses to the inverters to be used in advance. Assign a same subnet mask
value to the modules to be used.
In this manual, IP addresses 192.168.50.and a subnet mask 255.255.255.0 are assigned to the inverters and the FX5U
CPU module.
For the power supply wiring of FR-E800-E series, refer to the following.
Chapter 2 Installation and Wiring in the FR-E800 Instruction Manual (Connection)
For the power supply wiring of FR-A800-E/F800-E, refer to the following.
Page 55 Power supply wiring
For the power supply wiring of FX5U CPU module, refer to the following.
Section 6.4 Power Supply Wiring in the MELSEC iQ-F FX5U User's Manual (Hardware)
For the power supply wiring of FX5UJ CPU module, refer to the following.
Page 54 Power supply wiring
FX5U CPU module Personal
computer
Ethernet
Hub
To be installed in advance.
FR Configurator2FR Configurator2
First inverter (Station number 1) Second inverter (Station number 2)
FR-E800-E
IP address :192.168.50.12
Subnet mask :255.255.255.0
IP address :192.168.50.11
Subnet mask :255.255.255.0
IP address :192.168.50.2
Subnet mask :255.255.255.0
IP address :192.168.50.1
Subnet mask :255.255.255.0

2 INVERTER SETTINGS
2.1 Names of the Parts on the Operation Panel 8
2
2INVERTER SETTINGS
2.1 Names of the Parts on the Operation Panel
Inverter parameter settings and error content can be checked on the operation panel.
*: The operation panel cannot be removed from the inverter.
For details on the FR-E800-E operation panel, refer to the following.
Section 2.1 Operation panel in the FR-E800 Instruction Manual (Function)
For details on the FR-A800-E/F800-E operation panel, refer to the following.
Page 55 Operation panel
No. Name Description
[1] Monitor (4-digit LED) Shows a numeric value (readout) of a monitor item such as the frequency and a parameter number.
[2] Unit indication Hz: ON when the actual frequency is monitored. (Blinks when the set frequency is monitored.)
A: ON when the current is monitored.
(Both "Hz" and "A" are OFF to indicate a value other than the frequency or the current.)
[3] Inverter operation mode LEDs PU ON when the inverter is in the PU operation mode.
EXT ON when the inverter is in the External operation mode. (Lit at power-ON at initial setting.)
NET ON when the inverter is in the Network operation mode.
Operation panel status LEDs MON ON or blinks only when the first, second, or third monitor is displayed.
PRM Lit to indicate parameter setting mode. The LED blinks when the inverter is in the easy setting mode.
PLC function LED P.RUN ON when the PLC function of the inverter is valid.
Operating status LED RUN ON or blinks during inverter running.
ON: During forward rotation operation.
Blinks slowly (1.4-second cycle): During reverse rotation operation.
Blinks quickly (0.2-second cycle): Operation is disabled although the start command is given.
Controlled motor type LED PM ON when the inverter is set to control the PM motor. The LED blinks during test operation.
[4] PU/EXT key Switches between the PU operation mode, the PUJOG operation mode, and the External operation mode.
[5] MODE key Switches the operation panel to a different mode.
[6] RUN key Executes a start command.
[7] SET key Confirms each selection. When this key is pressed during the monitor mode, the monitor item changes.
[8] STOP/RESET key Stops the operation commands. Resets the inverter when the protective function is activated.
[9] UP/DOWN key ( key) Changes the frequency and parameter settings.
[10] Operation status LEDs NS Shows communication status.
MS Shows inverter status.
LINK1 Shows connector for communication (PORT1) status.
LINK2 Shows connector for communication (PORT2) status.
[1]
[5] [6] [7] [8] [9]
[4]
[2] [3]
[10]

92 INVERTER SETTINGS
2.2 List of Related Parameters
2.2 List of Related Parameters
The following tables list the parameters which are required to be set.
To make communications between an inverters and a connected device, set the inverter parameters to match the
communication specifications of the connected device. Data communications cannot be made if the settings are not made or
if there is any setting error.
Required parameter settings
Parameter settings (for adjustment and operation)
For the FR-A800-E/F800-E parameters, refer to the following.
Page 55 Parameters
Parameter Name Initial
value
Setting value
(Inverter station
number 1)
Setting value
(Inverter station
number 2)
Description
Pr.77 Parameter write selection 0 2 Parameter write is set to [enable].
Pr.544 CC-Link extended setting 0 18 Set the function of the remote register for the CC-Link IE
Field Network Basic to [Compatible with the octuple
setting of CC-Link Ver.2].
Pr.1424 Ethernet communication
network number
1 1 Set this parameter when making communications
between the inverters and FR Configurator2.
Set a network number to Pr.1424 and a station number
to Pr.1425.
Pr.1425 Ethernet communication
station number
11 2
Pr.1427 Ethernet function selection 1 5001 5001 Set this parameter when making communications
between the inverters and FR Configurator2.
In this manual, use Pr.1427 and Pr.1428 with the initial
values.
Pr.1428 Ethernet function selection 2 45237 45237
Pr.1429 Ethernet function selection 3 45238 61450 Change the settings of the application to [CC-Link IE
Field Network Basic].
Pr.1430 Ethernet function selection 4 9999 9999 Use this parameter with the initial value.
Pr.1434 Ethernet IP address 1 192 192 Set an IP address of the inverter to be connected to
Ethernet.
Pr.1435 Ethernet IP address 2 168 168
Pr.1436 Ethernet IP address 3 50 50
Pr.1437 Ethernet IP address 4 1 11 12
Pr.1438 Subnet mask 1 255 255 Set a subnet mask which the IP address of the inverter
belongs to.
Pr.1439 Subnet mask 2 255 255
Pr.1440 Subnet mask 3 255 255
Pr.1441 Subnet mask 4 0 0
Pr.1449 Ethernet command source
selection IP address 1
0 192 Set an IP address of the FX5U CPU module.
Pr.1450 Ethernet command source
selection IP address 2
0168
Pr.1451 Ethernet command source
selection IP address 3
050
Pr.1452 Ethernet command source
selection IP address 4
02
Parameter Name Initial value Setting value
(Common for both
inverters)
Description
Pr.1432 Ethernet communication
check time interval
1.5 (= 1.5 seconds) 5.0 (= 5 seconds) Set "9999" during adjustment, and set a value in accordance
with the system specification during operation.
• 9999: No communication check (signal loss detection)
• 0: Ethernet communication is available, but the inverter
output is shut off in the NET operation mode.
• 1 to 9998: Set the interval of the communication check
(signal loss detection) time for all devices with IP addresses
in the range specified for Ethernet command source
selection (Pr.1449 to Pr.1454).

2 INVERTER SETTINGS
2.3 Ethernet Parameter Settings 10
2
2.3 Ethernet Parameter Settings
Parameters are set by connecting the inverters and the personal computer over Ethernet.
In this manual, FR Configurator2 is used to set the parameters. The following describes how to set the parameters using FR
Configurator2.
1. Start FR Configurator2, and select [Ethernet parameter setting] from the [Tool] menu bar.
2. When the inverters connected to the personal computer are detected automatically, their information, such as the model
and capacity, are displayed. Check that displayed information is correct, and click the [Batch assign] button.
When the personal computer has multiple Ethernet ports or uses a USB converter, the following window
appears. On this window, select a network adapter which is connected to the inverters.
Hub
Ethernet
FR-E800-E FR-E800-E

11 2 INVERTER SETTINGS
2.3 Ethernet Parameter Settings
3. Select the checkboxes of "Network No. / station No.", "Station No.", and "IP address / subnet mask", and click the [OK]
button. In this manual, the following setting values are used.
4. Click the [Write] button, and click the [Yes] button on the window, which asks whether to write the setting values to the
inverters, to reflect the setting values.
5. When the inverters are reset, the Ethernet parameter setting is complete. Click the [Close] button to close the "Ethernet
parameter setting" window, and move to the parameter setting.
Parameter Setting value
Network No. 1
Station No. 1
IP address 192.168.50.11
Subnet mask 255.255.255.0

2 INVERTER SETTINGS
2.4 Parameter Settings 12
2
2.4 Parameter Settings
1. Select [Project] on the toolbar [New].
2. In the "Connection setting" field, select "Ethernet" for "PC-side port" and "Not used" for "Through", and click the [Auto
recognize] button. Click the [Yes] button on the window, which asks whether to clear the current settings, to execute
automatic recognition.
When the personal computer has multiple Ethernet ports or uses a USB converter, the following window
appears. On this window, select a network adapter which is connected to the inverters.

13 2 INVERTER SETTINGS
2.4 Parameter Settings
3. When the auto-recognized inverter information is displayed, check that the displayed model, capacity, and other
information are correct. Click the [OK] button.
4. In the [Project] window, the inverter models of station number 1 and station number 2 are displayed. Double-click
"Parameter" under the inverter model to open the parameter list.
If the [Project] window is not displayed, select [Project window] from [Docking Window] in the [View] menu to
open the window.

2 INVERTER SETTINGS
2.4 Parameter Settings 14
2
5. Enter the parameter setting values. For parameters and setting values to be used, refer to Page 9 List of Related
Parameters.
For parameter setting on the operation panel, refer to the following.
Section 2.1.2 Basic operation of the operation panel in the FR-E800 Instruction Manual (Function).
The following parameters are set during Ethernet parameter setting, therefore, entering their setting values is
not necessary. (Page 10 Ethernet Parameter Settings)
• Pr.1424 (Ethernet communication network number)
• Pr.1425 (Ethernet communication station number)
• Pr.1434 to Pr.1437 (Ethernet IP address)
• Pr.1438 to Pr.1441 (Subnet mask)

15 2 INVERTER SETTINGS
2.5 Writing Data to the Inverters
2.5 Writing Data to the Inverters
The parameter setting values entered in the parameter list are written to each inverter.
1. Click the following icon on the toolbar to go online.
2. Click [Batch write], and click the [Yes] button on the window which asks whether to write the parameters. After the
parameters are written to the inverter, reset the inverter.
A parameter list can be switched between the station number 1 and the station number 2 by selecting the
following the station number list.
Grayed out when
the inverter is offline.
Activated when
the inverter is online.
the

2 INVERTER SETTINGS
2.6 Inverter Reset 16
2
2.6 Inverter Reset
After the parameters are changed, the inverters must be reset. Otherwise, the changed settings are not reflected. In this
manual, FR Configurator2 is used to reset the inverters. The following describes how to reset the inverters using FR
Configurator2.
1. Select [Fault history] from the [Diagnose] menu bar on the toolbar.
2. Click [Inverter reset], and click the [Yes] button on the window which asks whether to reset the inverter. When the inverter
(station number 1) is reset, the parameter setting is complete.
3. Set the parameters for the inverter station number 2 using the same procedure as the inverter station number 1.
For the parameter setting of the inverter station number 2, start from the step 4 of in 2.4 Parameter Setting. (For the parameter
setting procedure, refer to Page 12 Parameter Settings.)
An alarm history can be switched between the station number 1 and the station number 2 by selecting the
following station number list.

17 3 PROGRAMMABLE CONTROLLER SETTINGS
3.1 Part Names
3PROGRAMMABLE CONTROLLER SETTINGS
3.1 Part Names
For the part names of the FX5U CPU module, refer to the following.
Section 1.1 Part Names in the MELSEC iQ-F FX5U User's Manual (Hardware)
For the part names of the FX5UC and FX5UJ CPU modules, refer to the following.
Page 54 Part names
3.2 Downloading the FB Library
In this manual, the FB library for CC-Link IE Field Network Basic compatible inverters is used.
To obtain the FB library, please contact your local Mitsubishi Electric representative.

3 PROGRAMMABLE CONTROLLER SETTINGS
3.3 Importing the FB Library 18
3
3.3 Importing the FB Library
This section describes how to register the obtained FB library to GX Works3.
Decompress the FB library folder (zip file) before registering the FB library.
1. Start GX Works3, and select [Project] on the toolbar [New].
In this manual, the following setting values are used.
2. Select [Project] on the toolbar [Library Operation] [Register to Library List] [Library].
3. When the following window appears, click the [OK] button.
Item Setting value
Series FX5CPU
Type FX5U
Program Language Ladder

19 3 PROGRAMMABLE CONTROLLER SETTINGS
3.3 Importing the FB Library
4. Select the "INVERTER-CC-IEF-Basic_F.mslm" file in the decompressed FB library folder, and click the [Open] button.
5. The selected file is added to [Library] in the "Element Selection" window.
If the "Element Selection" window is not displayed, select [View] on the toolbar [Docking Window] 
[Element Selection] to open the window.