Mitsubishi Electric ME96 Series Instruction manual

POWER METER
MODEL
ME96 SERIES
QUICK START MANUAL
Mitsubishi Electric Automation, Inc.

ME96 QUICK START MANUAL
2
1. INTRODUCTION.................................................................3
1.1 SAFETY.............................................................................3
1.2 AVAILABLE MODELS........................................................4
1.3 REQUIRED ACCESSORIES .............................................4
2. DIMENSIONS......................................................................4
3. INSTALLATION ..................................................................4
3.1 SPECIFICATIONS.............................................................5
3.2 MOUNTING INSTRUCTIONS...........................................6
4. SPECIFICATIONS AND WIRING..................................6
4.1 WIRING.............................................................................6
4.2 RATED VOLTAGE FOR EACH PHASE/WIRE SYSTEM ...8
5. POWER METER CONFIGURATION...........................8
5.1 DISPLAY AND BUTTON FUNCTION.................................8
5.2 POWER METER SETUP AND MENU DIAGRAM ............9
5.3 POWER METER SETUP FOR VOLTAGE
AND CURRENT SETUP .................................................10
6. OPERATION ......................................................................10
6. 1 DISPLAY CHANGE ........................................................10
6. 2 PHASE CHANGE...........................................................10
6. 3 BAR GRAPH DISPLAY .................................................. 11
6. 4 MAXIMUM VALUE AND MINIMUM VALUE DISPLAY.... 11
6. 5 ALARM DISPLAY AND HOW TO CANCEL .................... 11
6. 6 HARMONICS DISPLAY.................................................. 11
6. 7 EXPANDED COUNTING DISPLAY ................................ 11
7. MAINTENANCE ................................................................ 11
8. TROUBLESHOOTING....................................................12
Mitsubishi Electric Automation, Inc.

ME96 QUICK START MANUAL
3
1. INTRODUCTION
ME96 Series Power Meters are high accuracy meters for electrical
load monitoring. ME96 Family meters are panel mount with a large
LCD display and native Modbus®RTU communication. ME96 can
be installed on power distribution panels, motor control centers,
machine panels or other custom panels. ME96 family can meter
voltage measurement directly up to 480V WYE connection; external
step down voltage transformer is required for higher voltages. For
current measurements, ME96 family requires external 1 Amp/5 Amps
secondary current transformers. Power supply requirement for ME96
power meter is 120V-240 VAC 50/60Hz. This meter meets IEC62053
Class 0.5S/1 accuracy for Watt-Hour. ME96 SSR and SSH Models
also have power quality capability. ME96 Family meters provide
metering and power quality information that can be used for energy
cost allocation, power demand management, or troubleshooting power
quality problems.
Always read these instructions before using this equipment. For
personal and product safety please read the contents of these
operating instructions carefully before using. Please save this manual
to make it accessible when required and always forward it to the end
user.
1.1 SAFETY
Do not attempt to install, operate, maintain or inspect the inverter until
you have read through the Quick Start Manual carefully and can use
the equipment correctly. Do not use this product until you have a full
knowledge of the equipment, safety information and instructions. In
this manual, the safety instruction levels are classified into “DANGER”
and “CAUTION”.
DANGER Indicates that incorrect handling may cause
hazardous conditions, resulting in death or severe injury.
CAUTION Indicates that incorrect handling may cause
hazardous conditions, resulting in medium or slight personal injury
or physical damage.
Depending on the circumstances, procedures indicated by CAUTION
may also cause severe injury. It is important to follow all precautions for
personal safety.
CAUTION ENVIRONMENT
Use this instrument in an environment that meets the normal service
conditions per the following points:
• Ambient temperature: -5 to +55°C, average day temperature 35°C or
less.
• Humidity: 0 to 85%RH, non condensing.
• Altitude: 2000m or less
• Pollution Degree: 2 or less
• Atmosphere without corrosive gas, dust, salt, oil mist.
• Indoor use
• Transient over voltage 4000V or less.
• Use in a place without excessive shocks or vibration.
• Do not expose to rain and water drips.
• Do not expose to direct sunlight.
• Use in area in where no pieces of metal and an inductive substance
disperse.
• Do not expose to strong electromagnetic field and ambient noises.
nINSTALLATION INSTRUCTIONS
• This instrument should be installed and used by a qualified
electrician.
• The instrument must not be powered and used until its definitive
assembly on the cabinet’s door.
• Verify the following points; Auxiliary power supply and measuring
ratings.
Auxiliary Power
Supply
100-240V AC ±15% (50-60Hz) 8VA
100-240V DC +15% -30% 5W
MA, MB
Terminals
Ratings
Voltage
3-PHASE 4-WIRE: MAX277V(L-N)/480V(L-L)
3-PHASE 3-WIRE(DELTA): MAX220V(L-L)
3-PHASE 3-WIRE (STAR): MAX440V(L-L)
1-PHASE 3-WIRE: MAX220V(L-N)/440V(L-L)
1-PHASE 2-WIRE(DELTA): MAX220V(L-L)
1-PHASE 2-WIRE(STAR): MAX440V(L-L)
Cat. II P1, P2, P3, PN
terminals
Current 5A (via current transformer)
(max 30VAC) Cat. II
+C1, C1, +C2,
C2, +C3, C3
terminals
Frequency 50/60Hz
Provide the basic insulation externally at the current input terminals.
Voltage-measuring and current-measuring circuit terminals should be
permanently connected.
MODBUS®RTU communication T/R+, T/R-, Ter terminals max 35VDC
• Tighten the terminal screws with the specified torque and use the
suitable pressure connectors and suitable wire size.
• When wiring the instrument, be sure that it is done correctly by
checking the instrument’s wiring diagram.
• Be sure there are no foreign substances such as sawdust or wiring
debris inside the instrument.
• Do not drop this instrument from a high place. If you drop it and the
display is cracked, do not touch the liquid crystal or get it in your
mouth. If the liquid crystal is touched, wash it away at once.
• In order to prevent invasion of noise, do not bunch the control
wires or communication cables with the main circuit or power
wire, or install them close to each other. The distance between
communicational signal lines, input signal lines and power lines,
high voltage lines running parallel to each other are shown below.
Conditions Length
Below 600V, or 600A power lines 30cm or more
Other power lines 60cm or more
CAUTION OPERATION INSTRUCTIONS
• When the external terminals are connected to the external
equipments, the instrument and the external equipments must not
be powered and used until its definitive assembly on the cabinet’s
door.
• The rating of the terminal of the external equipment should satisfy
the rating of the external terminal of this instrument.
CAUTION MAINTENANCE INSTRUCTIONS
• Do not touch the terminals while all the circuits connected to this
instrument are alive.
• Do not disassemble or modify the instrument.
• Do not contact a chemical dust cloth to the instrument for a long
time, or do not wipe it with benzene, thinner, alcohol.
• Wipe dirt off the surface with a soft dry cloth.
• Check the following points, (at the cycle of six months to one year)
 Condition of the appearance
 Unusual sound, a smell, and generation of heat
 Condition of the display
 Condition of the wiring and the attachment
Mitsubishi Electric Automation, Inc.

ME96 QUICK START MANUAL
4
CAUTION STORAGE CONDITIONS
• Ambient temperature: -25 to +75°C,average day temperature
35°C or less
• Humidity: 0 to 85%RH, non condensing.
• Atmosphere without corrosive gas, dust, salt, oil mist.
• A place without excessive shocks or vibration.
• Do not expose to rain and water drips.
• Do not expose to direct sunlight.
• An area in where no pieces of metal and an inductive substance
disperse.
CAUTION DISPOSAL
• When disposing of this product, treat it as industrial waste.
• A battery is not used for this product.
nWARRANTY
The period of warranty is earlier date of either 18 months from the
manufacture date or 1 year from the sale date, except in the case that
the failure has been caused by bad handling of the product, provided
that it has been installed according to the manufacturer’s instructions.
nFCC
This instrument complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This instrument may not
cause harmful interference, and (2) this instrument must accept any
interference received,including interference that may cause undesired
operation.
Please contact the service network when the equipment has a
breakdown or abnormality.
Conditions Length
Below 600V, or 600A power lines 30cm or more
Other power lines 60cm or more
Protective conductor terminals for mains circuits shall be at least
equivalent in current-carrying capacity to the mains supply terminals.
If the protective conductor terminals is also used for other bonding
purposes, the protective conductor shall be applied first and secured
independently of other connections
1.2 AVAILABLE MODELS
Model Name Main Measurement Items Transmission/Option
Specifications
ME96-SSH-MB
(High-spec class)
A, DA, V = ±0.1%
W, var, VA, Hz = ±0.2%
PF = 1.0%
Wh = class 0.5s (IEC 62053-22)
varh, Vah = class 2.0 (IEC
62053-23)
Harmonics = 31st-deg (max)
Rolling demand
MODBUS® RTU
communication
ME96-SSR-MB
(Standard class)
A, DA, V = ±0.2%
W, var, VA, Hz = ±0.5%
PF = 2.0%
Wh = class 1.0 (IEC 62053-21)
varh = class 2.0 (IEC 62053-23)
Harmonics = 13th-deg (max)
ME96-SSE-MB
(Economy class)
A, V = ±0.5%
W, Hz = ±0.5%
PF = 2.0%
Wh = class 1.0 (IEC 62053-21)
1.3 REQUIRED ACCESSORIES
External 1amp or 5amp current transformers (CT) are required
and not include with this power meter. Shorting blocks are strongly
recommendation for CT wiring to power meter. Use 1amp fuses for
voltage connection to power meter. ME96 can meter voltage data for
up to 480V WYE directly, use of external step down transformer is
required for above 480V and medium voltage applications.
2. DIMENSIONS
ME96 Power Family Meter
20.7
86.2
（106.9）
95.8（COVER）
95.8（COVER）
91.6（PANEL CUT）
91.6（PANEL CUT）
3. INSTALLATION
DANGER Shut off the external power supply for the unit in all phases
before installing or wiring. Failure to do so may cause an electric shock
or damage the unit.
To ensure safety, read the following items carefully before use and
always comply with procedures during use. Special attention should
be given to items enclosed in a box and marked “Caution.” Additionally,
please carefully read the operations manual supplied with the product
before use, and ensure that the manual read by the end user as well.
nUSAGE ENVIRONMENT AND CONDITIONS
Do not use these products under any of the following conditions. Doing
so may cause erroneous operation and/or reduced service life.
• Ambient temperature is outside the range of -5~55°C
• Daily average temperature over 35°C
• Relative humidity over 85% or presence of condensation
• Presence of excessive dust, corrosive gas, salt or oil/smoke
• Product is subject to excessive vibration or shock
• Product is in direct contact with rain, water drops or sunlight
• Altitude is above 2,000m
• Excessive external noise
• Pollution level is 2 or higher
• Transient overvoltage is 4,000V or higher
• Presence of metal fragments or conducting substances
nINSTALLATION
Please note the following items regarding installation. To ensure safety,
installation is to be performed by a qualified technical electrician.
• Affix the main unit to the panel before use
Mitsubishi Electric Automation, Inc.

ME96 QUICK START MANUAL
5
• The LCD display contrast changes depending on the angle from
which it is viewed. Install it in a position that ensures a suitable angle
of view.
• Tighten screws using a torque of approx. 0.3~0.5N·m
• To prevent damage to the LCD, take care not to subject the LCD/
front of the main unit to shock/impact.
Auxiliary power supply and instrument ratings
Auxiliary power supply AC100~240V (±15%) 50-60Hz
DC100~240V (−30%, +15%)
Instrument
ratings
Voltage
3-phase, 4-wire: Max. 277/480VAC
3-phase, 3-wire: Delta connection: Max. 220VAC, Star
connection: Max. 440VAC
1-phase, 3-wire: Max. 220/440VAC
1-phase, 2-wire: Delta connection: Max. 220VAC, Star
connection: Max. 440VAC
Current 5A/1A
Frequency 50-60Hz (dual use)
CAUTION CONNECTIONS
• To ensure safety, connections are to be performed by an electrical
engineer qualified in wiring.
• Check connection diagrams carefully before performing connections.
Incorrect connections may result in VT burnout caused by a VT
secondary-side short circuit or high voltage on the CT secondary
side, which may lead to device malfunction, fire or electrical shock.
• Do not work with live wires; there is a risk of electric shock and
exposure to high voltage due to short-circuiting or CT secondary
side opening, which may lead to malfunction, fire or electrical shock.
• Use electrical wire sizes compatible with the rated current. Use of
unsuitable sizes may cause heat generation, which may lead to a
fire.
• After performing connections, check that no connections have been
missed. Missed connections may result in erroneous operation or
high voltage on the CT secondary side, which may lead to a fire or
electrical shock.
nPREPARATIONS BEFORE USE
• Before use, perform settings such as the VT primary voltage, CT
primary current, power scale and demand time limit in accordance
with the operations manual supplied with the product; setting errors
may cause incorrect measurement/operation.
nUSAGE PROCEDURES
• Use the products within the rated range. Using the products
outside the rated range may cause erroneous operation or product
malfunction.
• Do not use the products for special applications such as nuclear
power, aerospace or medical devices/systems.
CAUTION Do not make any modifications to the products. Using
products after modification may cause a malfunction, electrical shock
or fire.
nREPAIRING AT TIME OF MALFUNCTION/ERROR
• If a product listed in this catalog malfunctions, read the
troubleshooting section of the operations manual (detailed version)
and confirm the symptoms. If the problem is not listed, please
contact Mitsubishi Electric at Amzsuppor[email protected]
3.1 SPECIFICATIONS
Type ME96-SSH-MB, ME96-SSR-MB, ME96-SSE-MB
Phase Wire System 3-Phase 4-Wire, 3-Phase 3-Wire (3CT, 2CT), 1-Phase 3-Wire,
1-Phase 2-Wire (common)
Rating
Current AC5A, AC1A (common)
Voltage
3-Phase 4-Wire: max AC277/480V
3-Phase 3-Wire: (DELTA)max AC220V,
(STAR) max AC440V
1-Phase 3-Wire: max AC220/440V
1-Phase 2-Wire: (DELTA)max AC220V,
(STAR) max AC440V
Frequency 50-60Hz (common)
Item Measurement Item ME96-SSH-
MB
ME96-SSR-
MB
ME96-SSE-
MB
Measurement Elements
Current (A) A1, A2, A3, AN,
A AVG ±0.1% ±0.2% ±0.5%
Current Demand (DA) DA1, DA2, DA3,
DAN, DAAVG ±0.1% ±0.2% -
Voltage (V)
V12, V23, V31,
VAVG (L-L), V1N,
V2N, V3N, VAVG
(L-N)
±0.1% ±0.2% ±0.5%
Active Power (W) W1, W2, W3, ∑W ±0.2% ±0.5 % ±0.5 %
Reactive Power (var) var1, var2, var3,
∑var ±0.2% ±0.5 % -
Apparent Power (VA) VA1, VA2, VA3, ∑VA ±0.2% ±0.5 % -
Power Factor (PF) PF1, PF2, PF3, ∑PF ±1.0% ±2.0 % ±2.0 %
Frequency (Hz) Hz ±2.0 % ±0.5 % ±0.5 %
Active Energy (Wh) Imported, Exported
class0.5S
(IEC62053-
22)
class1.0
(IEC62053-
21)
class1.0
(IEC62053-
21, Only
Imported
Lag)
Reactive Energy (varh)
Imported Lag,
Imported
Lead,Exported Lag,
Exported Lead
class2.0
(IEC62053-
23)
class2.0
(IEC62053-
23)
-
Apparent Energy (VAh) Imported + Exported class2.0 - -
Harmonic Current (HI) Only odd number ±2.0%
(1 to 31)
±2.0%
(1 to 13) -
Harmonic Voltage (HV) Only odd number
Rolling Demand (DW) Rolling Block, Fixing
Block ±0.2% - -
Periodic Active Energy
(Wh)
Periodic Active
Energy 1, Periodic
Active Energy 2
class0.5S
(IEC62053-
22)
class1.0
(IEC62053-
21)
-
Operation Time (h) Operation time 1,
Operation time 2 (Reference)
Analog Output Response
Time 2 s or less (HI and HV:10s or less)
Measuring
Method
Instantaneous
Value
A•V: RMS calculation,W•var•VA•Wh•varh•VAh: Digital
multiplication, PF: Power ratio calculation, Hz: Zero-cross, HI•HV:
FFT
Demand
Value DA: Thermal type calculation , DW: Rolling Demand calculation
Display
Type LCD with backlight
Maximum
Number
of Display
Digits or
Segment
Number
Number of
Display Digits
Upper stage display: 6 digits, Middle stage display: 6 digits, Lower
stage display: 6 digits
A, DA, V, W, var, VA, PF: 4 digits DW, Hz: 3 digits Wh, varh, VAh: 9
digits: 6 digits or 12 digits possible: Harmonic total distortion ratio:
3 digits Harmonic RMS value: 4 digits Operation time: 6 digits
Digital input/output: I/O
Bar Graph 21 Segment-Bar graph, 22 Segment- Indicator
Display Updating Time
Interval 0.5s, 1s
Communication Specification MODBUS®RTU communication
Power Failure Compensation
Non volatile memory (Items: Setting value, MAX/MIN value,
Active/Reactive/Apparent energy, Periodic Active Energy, Rolling
Demand, Operation time)
VA
Consumption
VT 0.1VA/phase, 0.2VA (at direct input 220V)
CT 0.1VA/phase
Aux. Power 7VA (AC110V), 8VA (AC220V), 5W (DC100V)
Auxiliary Power AC100-240V (±15%), DC100 to 240V (-30% +15%)
Weight 0.5kg
Dimension (H x W x D) 96 x 96 x 86
Attachment Method Embedding attachment
Operating Temperature/
Humidity
-5 to +55°C (average temperature: 35°C or less per day)
0 to 85%RH, non condensing
Storage Temperature/
Humidity
-25 to +75°C (average temperature: 35°C or less per day)
0 to 85%RH, non condensing
Mitsubishi Electric Automation, Inc.

ME96 QUICK START MANUAL
6
3.2 MOUNTING INSTRUCTIONS
Review Package Contents
Part Name Quantity Specifications
Attachment lug
(with screw) 2
nDIMENSION OF PANEL
Panel hole dimensions are as shown in the following figure. It can be
attached to a panel with thickness of 1.6 to 4.0mm.
nVIEW ANGLE
The contrast of the display changes at view angle. Mount it at the
position that is easy to see.
nATTACHMENT
For attachment of the basic device into the panel hole, attach
according to the following procedure.
NOTE: The attachment lug is installed in two holes of the top and
bottom of the basic device. Tighten the screws of the lug, and fix
onto the panel. To prevent damage to the panel and screws, do not
fasten screws too tightly. Recommended torque for these products:
0.3~0.5N·m (approx. half of standard torque) Also, please tighten the
upper and lower screws at the same time.
4. SPECIFICATIONS AND WIRING
CAUTION MAINTENANCE INSTRUCTIONS
• Do not connect with hot-line
• Do not use in the condition that the secondary circuit of CT is
opened.
• Do not use in the condition that the secondary circuit of VT is
short-circuited.
• The wire size has to be suited for the rated current and rated voltage.
Terminals of +C1, C1, +C2, C2, +C3, C3: AWG24 to 14 (For UL
recognized: Single wire of AWG22 to 16)
• Terminals of instrument main body (except for +C1, C1, +C2, C2,
+C3, C3 terminals): AWG24 to 14 (For UL recognized: AWG24 to
18). When using a stranded wire, use a ferrule.
4.1 WIRING
1. Remove the wire casing at the end of the wire and solder to the rod
terminal.
2. With the lever pushed in, insert the wire and then release the lever
to connect.
Confirmations
After wiring, make sure the following:
• All wiring is connected
• There is no mistake in wiring
PROTECTIVE SHEET
There is a protective sheet covering the LCD screen to prevent
scratching during panel installation. Please remove the sheet before
using the meter. When removing the sheet, the LCD may turn on due
to the static electricity generated. This is not abnormal; the LCD will
turn off after a short time.
INSTALLATION POSITION
If installing the unit at the panel edge, choose an installation position
where there is sufficient space for wiring work.
92 +0.5
0
92 +0.5
0
Viewing angle
60°
10°
60°
60°
(overhead view)(side view)
Insert hole Lever
Mitsubishi Electric Automation, Inc.

ME96 QUICK START MANUAL
7
WIRING DIAGRAMS
Three phase 4-wire system: Direct input
Three phase 4-wire system: With VT
Three phase 3-wire system: Direct input, 2CT
Three phase 3-wire system: With VT, 3CT
Single phase 3-wire system
Single phase 2-wire system: With VT
NOTE:
1. The voltage input terminal will vary depending on if it is a 3-phase,
3-wire system or otherwise.
2. VT/CT polarity errors will cause incorrect measurement.
3. Always use the grounding terminal in a grounded state. Perform
grounding with a grounding resistance of 100Ω or less. Insufficient
grounding may cause erroneous operation.
4. Use shielded twisted-pair cables for transmission signal lines.
5. Use terminal resistance (120Ω) for devices at both ends of the
MODBUS®RTU communication transmission line. These meters
can be terminated at 120Ω by short-circuiting the “T-” and “Ter”
terminals.
6. Use the thickest possible grounding wire to ensure low
impedance.
7. MODBUS®RTU transmission signal cables must not be in close
proximity or bundled with high-voltage cables.
1. Auxiliary power supply:
100-240VAC or VDC
2. Fuse: 0.5A
*1 For low-voltage circuits,
secondary-side grounding of
instrument-use voltage/current
transformers is not required.
*2 Connection to NC terminal is
prohibited.
2
T/R－
T/R＋
T/R＋
T/R－
ＭＡ
ＭＢ
ＳＬＤ
ＳＬＤ
Ｔｅｒ
MODBUS®RTU
Communication
k
K
L
Ｃ２
3
Load
0
1
(+)
(−)
＋Ｃ１
Ｃ１
＋Ｃ２
＋Ｃ３
Ｃ３
Ｐ１
Ｐ２
Ｐ３
ＰＮ
K
L
lk
l
K
L
k
l
Protective
Earthing
MODBUS®RTU
Communication
12
1Auxiliary power supply:
100-240VAC or VDC
2Fuse: 0.5A
*1 For low-voltage circuits,
secondary-side grounding
of instrument-use
voltage/current
transformers is not
required.
*2 Connection to NC terminal
is prohibited.
T/R－
T/R＋
T/R＋
T/R－
ＭＡ
ＭＢ
ＳＬＤ
ＳＬＤ
Ｔｅｒ
2
Ｃ２
＋Ｃ１
Ｃ１
＋Ｃ２
＋Ｃ３
Ｃ３
Ｐ１
Ｐ２
Ｐ３
ＰＮ
u
v
u
v
u
v
U
V
U
V
U
VProtective
Earthing
MODBUS®RTU
Communication
k
Load
K
L
K
Llk
l
K
L
k
l
1
(+)
(−)
3 012
1Auxiliary power supply:
100-240VAC or VDC
2Fuse: 0.5A
*1 For low-voltage circuits,
secondary-side grounding of
instrument-use voltage/current
transformers is not required.
*2 Connection to NC terminal is
prohibited.
T/R－
T/R＋
T/R＋
T/R－
ＭＡ
ＭＢ
ＳＬＤ
ＳＬＤ
Ｔｅｒ
MODBUS®RTU
Communication
Protective
Earthing
MODBUS®RTU
Communication
2
k
K
L
Ｃ２
Load
1
(+)
(−)
＋Ｃ１
Ｃ１
＋Ｃ２
＋Ｃ３
Ｃ３
Ｐ１
ＮＣ
Ｐ３
Ｐ２
l
K
L
k
l
3 12
1Auxiliary power supply:
100-240VAC or VDC
2Fuse: 0.5A
*1 For low-voltage circuits,
secondary-side grounding
of instrument-use
voltage/current
transformers is not
required.
*2 Connection to NC terminal
is prohibited.
U
V
u
v
u
v
U
V
K
Ll
k
2
T/R－
T/R＋
T/R＋
T/R－
ＭＡ
ＭＢ
ＳＬＤ
ＳＬＤ
Ｔｅｒ
Protective
Earthing
MODBUS®RTU
Communication
Ｃ２
＋Ｃ１
Ｃ１
＋Ｃ２
＋Ｃ３
Ｃ３
Ｐ１
ＮＣ
Ｐ３
Ｐ２
k
K
L
Load
l
K
L
k
l
1
(+)
(−)
3 12
1Auxiliary power supply:
100-240VAC or VDC
2Fuse: 0.5A
*1 For low-voltage circuits,
secondary-side grounding of
instrument-use voltage/current
transformers is not required.
*2 Connection to NC terminal is
prohibited.
Ｐ２
T/R－
T/R＋
T/R＋
T/R－
ＭＡ
ＭＢ
ＳＬＤ
ＳＬＤ
Ｔｅｒ
MODBUS®RTU
Communication
Protective
Earthing
MODBUS®RTU
Communication
2
k
K
L
Ｃ２
Load
1
(+)
(−)
＋Ｃ１
Ｃ１
＋Ｃ２
＋Ｃ３
Ｃ３
Ｐ１
Ｐ３
ＰＮ
l
K
L
k
l
0 12
1Auxiliary power supply:
100-240VAC or VDC
2Fuse: 0.5A
*1 For low-voltage circuits,
secondary-side grounding
of instrument-use
voltage/current
transformers is not
required.
*2 Connection to NC terminal
is prohibited.
2
U
V
u
vＰ２
Ｐ３
2
T/R－
T/R＋
T/R＋
T/R－
ＭＡ
ＭＢ
ＳＬＤ
ＳＬＤ
Ｔｅｒ
Protective
Earthing
MODBUS®RTU
Communication
ＰＮ
Ｃ２
＋Ｃ１
Ｃ１
＋Ｃ２
＋Ｃ３
Ｃ３
Ｐ１
k
K
L
Load
l
1
(+)
(−)
1
Mitsubishi Electric Automation, Inc.

ME96 QUICK START MANUAL
8
4.2 RATED VOLTAGE FOR EACH PHASE/WIRE SYSTEM
Phase/Wire Connection Rated Voltage Figure
Three phase 4-wire Star Max. 277VAC (L-N)/480VAC(L-L) 1
Three phase 3-wire Delta Max. 220VAC (L-L) 2
Star Max. 440VAC (L-L) 3
Single phase 3-wire - Max. 220VAC (L-N)/440VAC(L-L) 4
Single phase
2-wire*
Delta Max. 220VAC (L-L) 5
Star Max. 440VAC (L-L) 6
5. POWER METER CONFIGURATION
5.1 DISPLAY AND BUTTON FUNCTION
DISPLAY
1 LEAD status
2 LAG status
3 Scale of the bar graph
4 Outside range
5 Index indicator
6 Bar graph status
7 Digital status
8 Unit
9 Metering status
10 Harmonics status
11 Communication status
12 Alarm status
13 Clock status
14 Test status
15 Step up mode status
16 Digital
nFUNCTION OF OPERATION BUTTON
Fig. 2. Three phase 3-wire (delta)Fig. 1. Three phase 4-wire (star)
Fig. 4. Single phase 3-wire
Fig. 3. Three phase 3-wire (star)
Fig. 6. Single phase 2-wire (star)Fig. 5. Single phase 2-wire (delta)
4
6
7
5
9
12
8
3
4
3
16
15 14 13 12 1011
SET RESET MAX/MIN PHASE DISPLAY
Set Button
Reset Button
+/–Button Maximum/Minimum
Button
Phase change
Button
Display change
Button
SET
■
■
RESET
○
■
■
PHASE
○
DISPLAY
○
－
○
＋
○
MAX/MIN
○
Function
Display changes.
Phase changes.
Mode changes to the max./min.
display and the instantaneous display.
An alarm conditions is individually
canceled.
The item expressed with the bar graph
is changed.
All the alarm conditions is canceled.
The display of Setting mode appears.
The display of Set value confirmation
mode appears.
○
: press ■: press on over 2 seconds ―: press simultaneously
Mitsubishi Electric Automation, Inc.

ME96 QUICK START MANUAL
9
5.2 POWER METER SETUP AND MENU DIAGRAM
HOW TO ACCESS THE SETTING ITEMS
1. Press the SET button and the RESET key simultaneously for 2
seconds to get in the setting mode.
2. Select a setting menu number by [+] or [-] button.
3. Change the contents in each setting menu.
4. After completion of setting, select ‘END’ in the setting menu and
press the SET button.
5. When the End display appears, press the SET button once again.
Display
Setting Menu End
End Display
CANCEL Display
Automatic migration.
T
ime constant for
current demand
T
ime constant for
Rolling demand
Frequency
CT current
V
T/direct
voltage
Display
Pattern
Phase
wire syste
Setting Menu
1
Setting Menu
3
Cancel the settings.
Save the setting.
The instrument is reset
or
Factory default setting
※2
※1
Password Protection Display
Example of Setting Mode
Example of Setting Value
Confirmation Mode
Harmonics
display
Reactive
power scale
A
ctive power
scale
Voltage scale
Current scale
Power factor
scale
Expanded
counting
ON Blinking
Password
setting change
Operation Mode
A
nalog output
1
Alarm value
Alarm delay
time
Alarmcancel
method
Back light flickers
during alarms
Motor starting
current delay time
A
larm item
Product
display
V
ersion
display
Backlight
brightness
Backlight
auto off
Display
update time
Output Limit
A
nalog output
4
A
nalog output
3
A
nalog output
2
Digital input
reset method
Digital input
/
output display
Periodic Active Energy
switchover setting
Periodic Active
Energy display
Phase display
setting
Operation time
value
Operation time
count target
Operation time
display
Setting Value Confimation Menu 9
Setting Menu 4 Setting Menu 5 Setting Menu6 Setting Menu 7 Setting Menu 8
Setting Mode or Setting Value Confirmation Mode
Skip remaining setting items during setting.
Set values return to the factory default value.
Shift from the operation mode to the password protectionmode.
DISPLAY
RESE T
＋
－
SET
PHASE
RESE T
SET
SET
SET
SET
＋
－
SET
SET
Pulse output
※1．A password input is needed when a password protection
setting is validated, and get in the setting mode from
the operation mode.
※2．For Setting Value Confirmation, it returns to Operation Mode.
※3．This is not display in Setting Mode.
Test Mode
※3
※3
PHASE
RESE T
Pulse/Alarm
oputput function
＋
－
IEC mode
setting
Rollingdemand
time constant
setting
Rolling Demand
display
Arrow in Figure
Action
Button operation
Shift from the operation mode to the setting mode.
＋
Press them simultaneously
Shift from the operation mode to the set value confirmation mode. Press it for 2 seconds.
Select the menu number to set or “End” .
or
Press it several times.
Get into each setting screen. Shift to the next setting item. Press it.
Go back to the previous setting item.
Press it.
Omitted infigure
Select a set value.
or
or
Press it several times.
Shift tothe End screen.
Press it.
Memorize the setting contents, and go back tothe operation mode. Press it.
Select "CANCEL."
Press it.
Cancel the settings. Press it.
Press it for 1 seconds.
＋
Press it for 2 seconds.
＋
Press it for 2 seconds.
MODBUS®RTU
address
MODBUS®RTU
baud rates
MODBUS®RTU
parity
MODBUS®RTU
stop bit
CC-Link
CC-Link
baud rates
CC-Lin
k
version
CC-Link
Reset
Station numbe
r
＜With ME-0040C-SS96 only＞
Communication
method selection
Setting Menu 2
Mitsubishi Electric Automation, Inc.

ME96 QUICK START MANUAL
10
5.3 POWER METER SETUP FOR VOLTAGE
AND CURRENT SETUP
In this setting menu 1, setting the basic contents as follows for correct
measurement. In the operation mode, after pressing the SET and the
RESET simultaneously for 2 seconds or more, the following operation
becomes available. An underline shows the initial value.
Setting menu
①Phase wire
②Display pattern
DISPLAY SET
DISPLAY
SET
DISPLAY SET
DISPLAY SET
Set the setting menu number to “1”. (Set as shown in the right
display.)
①Set the phase wire system.
②Set the display pattern. (Initial content: P13)
③Set the using VT or direct input (without VT).
Initial content
3- phase 3-wire or 1 phase 2-wire：using VT
3- phase 4-wire : direct input
YES
no
④Direct voltage
DISPLAY SET
④Set the rated voltage for scaling of the bar graph.
If you set “YES” on set up No.③, this display does not appear.
: using VT
: direct input
⑥Set the primary voltage value of VT in the case of using VT.
If you set “no” on set up No.③, this display does not appear.
Initial value
3-phase 3-wire or 1-phase 2-wire: 10000V
3-phase 4-wire : 200V
⑦Set the secondary current value of CT.
DISPLAY
SET
DISPLAY
SET
DISPLAY
SET
DISPLAY SET
⑤ Set the secondary voltage values of VT in case of using VT.
If you set “no” on set up No.③, this display does not appear.
63.5V
100V
110V
115V
120V
100V
110V
220V
5A 1A
③Using VT/
direct input
Note: : Display is made at this display setting.
: Set by the setting menu 4.
:
Select “P00”, and set display sequence and display position.
⑤VT secondary
voltage
⑥VT primary
voltage
⑦CT secondary
current
•
•
•
•
•
From top digit, select the value of the flickering digit by and .
The setting digit can be moved to right by the SET .
The setting digit can be moved to left by the DISPLAY .
The number of settable digits is 3 digits. Setting is available in the range from 60V to 750kV. (750000V)
If it is set to other range than 60V - 750kV, error display (E05) appears. At the moment of the error
display, press the SET , and review the set value, and set it once again.
When the SET is pressed at the most lower digit, the setting item goes tothe next one.
+–
Setting menu
According to the setting diagram, save the changed contents, or
continue to the other set up menu.
⑪
Set the time constant for calculating current demand.(only ME96SSH-MB,ME96SSR-MB)
SET
0 second
10 seconds
20 seconds
30 seconds
40 seconds
50 seconds
1 minute
2 minutes
3 minutes
4 minutes
5 minutes
6 minutes
7 minutes
8 minutes
9 minutes
10 minutes
15 minutes
20 minutes
25 minutes
30 minutes
Note) Even when the display pattern not display the current demand, this screen appears. If the current demand is
not necessary, press the SET as it is.
Time constant for
current demand
In the case of ME96SSH-MB
Additional Screen
Display Pattern
Current N Phase Current
Current Demand
N Phase
Current
Demand
Voltage Active Power Power Factor Reactive Power Apparent Power Frequency Active Energy(Imported) Active Energy(Exported) Reactive Energy Apparent Energy Active Energy
(Imported)
Active Energy(Exported)
Reactive Energy (Special)
Apparent Energy Periodic Active Energy Rolling Demand Harmonic Current/ Voltage Digital Input/Output Operation time
P01 ○ ○ ○ ○ ○ △ △ △ △ △
P02 ○ ○ ○ ○ ○ ○ ○ △ △ △ △ △ △
P03 ○ ○ ○ ○ ○ ○ ○○△△△ △ △
P04 ○ ○ ○ ○ ○ ○ ○○○ ○ ○ ○ △ △ ○ △ △ △ △ △
P05 ○ ○ ○ ○ ○△△△△△
P06 ○ ○ ○△△△ △ △
P07 ○ ○ ○○△△△ △ △
P08 ○ ○ ○○○○△△△△△△
P09 ○○○ ○ ○ △ △ △ △ △
P10 ○○○ ○ ○ ○ △ △ △ △ △
P11 ○○○ ○ ○ ○ ○ △ △ △ △ △ △
P12 ○○○ ○ ○ ○ ○○△△△ △ △ △
P13 ○ ○ ○ ○ ○ ○ ○○○ ○ ○ ○ △ △ ○ △ △ △ △ △
P00 □□□ □ □ □ □ □ □□□ □ □ □ △ △ △△△ △ △ △ △
<When①phase wire system is set to single-phase 3-wire>
Use only for direct input. This setting will be skipped.
63.5/110V
100/173V
110/190V
220/380V
240/415V
254/440V
277/480V
110V 220V 440V
110/220V 220/440V
(a)For 3-phase 4-
(phase to neutral voltage / phase to phase voltage)
(b)For 3- phase3-wire
(2CT, 3CT) or 1- phase 2-wire
(c)For 1- phase 3- wire(1N2,1N3)
(phase to neutral voltage / phase to phase voltage)
(b)For 3- phase 3- wire (2CT, 3CT)
or 1 phase 2-wire
(a)For 3- phase 4-wire
(phase to phase Voltage)
DISPLAY
SET
Set the interval time constant for rolling demand.(Only ME96SSH-MB)
（1）Interval time constant
Setting range Setting step
1 to 15 to 60(min) 1min
（2）Subinterval time constant
Setting range Setting step
1 to 60 (min) 1min
Time constant for
rolling demand
Set the frequency.
Frequency
50Hz 60Hz
Note1．
is changed, too.
Note2．Scale of the analog output is changed, too.
The scale value of the frequency of the bar graph display
•
•
•
•
•
⑧Set the primary current value of CT. (The initial value is 5A.)
⑧
⑨
⑨
⑩
⑩
⑪
CT primary
current
From top digit, select the value of the flickering digit by and .
The setting digit can be moved to right by the SET .
The setting digit can be moved to left by the DIAPLAY .
The number of settable digits is significant 3 digits. Setting is available in the range
from 1A to 30kA (30000A).
If it is set to other range than 1A - 30kA, error display (E05) appears. At the moment of the error
display, press the SET , and review the set value, and set it once again.
When the SET is pressed at the most lower digit, the setting item goes tothe next one.
+–
3P4 ：
-phase 4-wire
3P3．2CT ：
-phase 3-wire
（2CT）
3P3．3CT ：
-phase 3-wire
（3CT）
1P3．1N2 ：
-phase 3-wire
（1N2）
1P3．1N3 ：
-phase 3-wire （1N3）
1P2 ：
-phase 2 -wire
wire
・Error display (E05) appears when the interval time constant
is set to a value that is not dividable by the subinterval time
period. After that, please press , review the setting value
and it once again.
・Even when the display pattern not display the rolling demand,
this screen appears. If the rolling demand is not necessary,
press the as it is.
SET
SET
3
3
3
1
1
1
6. OPERATION
6. 1 DISPLAY CHANGE
By pressing DISPLAY, the measurement display will switch over.
Example of display change (display pattern: P01/phase wire: 3-phase
4-wire).
6. 2 PHASE CHANGE
By pressing PHASE, the current phase and the voltage phase will
switch over. Example of display change (phase wire: 3-phase 4-wire).
DISPLAY YALPSIDYALPSIDYALPSID
First display Second display Third display Fourth display
DISPLAY YALPSIDYALPSIDYALPSID
First display Second display Third display Fourth display
Example of phase switching (Phase wire System: 3-phase 4-wire)
PHASE
PHASE
PHASE
PHASE PHASEPHASE
PHASE
PHASE
Current phase 1
Active Power phase 1
Voltage phase 1N
Current phase 2
Active Power phase 2
Voltage phase 2N
Current phase 3
Active Power phase 3
Voltage phase 3N
Current phase 1
Active Power phase 1
Voltage phase 12
Current phase 2
Active Power phase 2
Voltage phase 23
Current phase 3
Active Power phase 3
Voltage phase 31
Current average
Active Power (total)
Voltage average (between phases)
Current average
Active Power (total)
Voltage average (between lines)
Mitsubishi Electric Automation, Inc.

ME96 QUICK START MANUAL
11
6. 3 BAR GRAPH DISPLAY
Measurement item to be displayed on bar graph can be selected. By
displaying others than the measurement items digitally displayed, 4
elements can be displayed at once.
Explanation of bar graph
In the bar graph, measurement elements shown by [u] or [ ] are
displayed. As for voltage, current, active power, reactive power, power
factor, frequency, they can be displayed on the bar graph even if they
are not set to display pattern.
Selection of bar graph
Press [+] or [-] to select measurement elements to be displayed the bar
graph.
6. 4 MAXIMUM VALUE AND MINIMUM VALUE DISPLAY
The maximum values and minimum values are displayed. Display
of maximum value and minimum value When MAX/MIN is pressed,
the display is changed into the maximum value and minimum value
display. And when MAX/MIN is pressed, the display changes back to
the instantaneous value display.
Reset the maximum value and minimum value When RESET is
pressed for 2 seconds or more, the displayed maximum value and
minimum value can be reset.
When RESET and [+] are pressed simultaneously for 2 seconds or
more, all the maximum values and minimum values are reset.
6. 5 ALARM DISPLAY AND HOW TO CANCEL
Display and Alarm output, How to cancel
Alarm condition: If a measurement value exceeds an alarm value, the
parts of display blink and an alarm relay contact closed.
ALARM CANCEL
Automatic If a measurement value falls below an alarm value, alarm is
automatically canceled.
Manual (HoLd)
After the measurement value falls below an alarm value, alarm is
maintained. The element of alarm is displayed and when RESET
is pressed, alarm is canceled.
ALARM DELAY TIME
If the condition that the limit was exceeded continues more than the
delay time, it will be in the alarm condition. The alarm output by rush
current can be prevented.
6. 6 HARMONICS DISPLAY
Harmonic RMS value and distortion ratio can be displayed.
Measurement items
ME96SSH-MB:Harmonic total, From 1st to 31st (only odd number)
ME96SSR-MB:Harmonic total, From 1st to 13th (only odd number)
Degree change
When [+] and [-] are pressed, harmonic degree change.
When PHASE is pressed, harmonic phase change.
6. 7 EXPANDED COUNTING DISPLAY
Active energy, reactive energy and apparent energy display Active
energy and reactive energy,apparent energy are display on unit
switching and the lower stage.
Active energy(Imported): Example of switching
012,345,678,901,234.567Wh
Wh,varh and VAh zero reset
When SET, RESET and PHASE are pressed simultaneously for 2
seconds, the measurement value of active energy (Wh),reactive
energy(varh) and apparent energy (VAh) are reset. This is effective only
in the instantaneous value display. Example for display.
7. MAINTENANCE
nUSAGE PROCEDURES
• Use the products within the rated range. Using the products
outside the rated range may cause erroneous operation or product
malfunction.
• Do not use the products for special applications such as nuclear
power, aerospace or medical devices/systems.
CAUTION Do not make any modifications to the products. Using
products after modification may cause a malfunction, electrical shock
or fire.
nREPAIRING AT TIME OF MALFUNCTION/ERROR
• If a product listed in this catalog malfunctions, read the
troubleshooting section of the operations manual (detailed version)
and confirm the symptoms. If the problem is not listed, please
contact Mitsubishi Electric at Amzsuppor[email protected].
nMAINTENANCE/INSPECTIONS
• Wipe away any dust/dirt on the surface of product with a soft cloth.
• Do not leave chemical cloths, etc. in contact with the product for long
periods, and avoid the use of benzene, thinner, etc. when wiping
the product surface. Doing so may cause deformation or cause the
coating to peel away.
• To ensure correct use for the full service life of the product, please
perform the following inspections:
 Check for damage to the product
 Check for display malfunctions (e.g., does not respond to input)
 Check for loose installation or terminal block wire connections
(check regularly once every six months/year) always making sure
that power has been turned off beforehand).
 Check for unusual smell, noise or rise in temperature.
nSTORAGE
• Do not store the product for long periods of time under any of the
following conditions. Doing so may lead to a malfunction or reduced
service life.
• Ambient temperature outside the range of -25~+75°C
Alarm cancel method
Automatic
(Auto)
Manual
(HoLd)
Display
Output
(Alarm relay contact)
Display
Output
(Alarm relay contact)
Alarm condition
ALARM , HI or LO
are blink
Closed
ALARM , HI or LO
are blink
Closed
Normal condition
State usually
Opened
ALARM , HI or LO
are lighting
Closed
State
usually
Opened
cancel
Unit：M
Lower digit magnification display Unit：tinUnon ：k
＋
－
Press and simultaneously for 2 seconds
Reactive energy
(Imported lag)
Reactive energy
(Imported lead)
Reactive energy
(Exported lag)
Reactive energy
(Exported lead)
Mitsubishi Electric Automation, Inc.

ME96 QUICK START MANUAL
12
• Daily average temperature of more than 35°C
• Relative humidity exceeding 85% or condensation present
• Excessive dust, corrosive gas, salt or oil/smoke present
• Product is subject to excessive vibration or shock
• Product is in direct contact with rain, water drops or sunlight
nDISPOSAL
These products do not use nickel-cadmium batteries. Dispose of them
as industrial waste.
nWARRANTY PERIOD
The warranty period for the products in this catalog expires one year
from the date of purchase or one year and six months after the date of
manufacture; whichever is earliest. Even during the warranty period,
the warranty shall not apply to malfunctions attributable to intentional
negligence or erroneous use by the customer, and the fee for any
repair required as the result of such negligence shall be the liability
of the customer. Mitsubishi Electric shall not be liable for: Damage
that cannot be attributed to Mitsubishi Electric; lost opportunity or
earnings resulting from failure of a Mitsubishi Electric product; damage,
secondary damage or compensation for an accident resulting from
special circumstances regardless of whether or not the circumstances
were foreseeable; or damage to products or other services for products
not manufactured by Mitsubishi Electric.
nPRODUCT EXCHANGE CYCLE
Although it depends on usage conditions, as a guide, it is
recommended that the products listed in this catalog be renewed after
10 years.
8. TROUBLESHOOTING
In the case of abnormal noise, odor, smoke, or heat generation from
this instrument, turn it off at once. Check the followings before you ask
for repair.
Condition Possible Cause Solution
Display
The display is not lit.
Auxiliary power supply
is not impressed on MA
and MB terminals.
Impress auxiliary power
supply.
When the auxiliary power
supply is impressed,
display is not lit soon.
This is not an error. For
about a few seconds
after auxiliary power
source is charged,
initialization of internal
circuit is carried out.
Use it as is.
The back light is not lit.
The back light may be
set to auto off (Auto). (If it
turns on after you press
an operation button, it
means the backlight is
set to auto off.)
When the auto off is
enabled, it automatically
turns off in 5 minutes.
Continue using it as it is
or change the setting to
HoLd (it stays on).
The display becomes
black.
It may become black
owing to static electricity. It goes off after a while.
“End” display remains. The product is still in the
setting mode. Press SET
Measurement Error
The current and voltage
have large errors.
The settings for VT /
direct voltage and CT
primary current may be
incorrect.
Please check the set
values for VT / direct
voltage and CT primary
current.
The current and voltage
are correct, but the active
power, reactive power,
and power factor have
large errors.
The wiring for VT/CT or
for the measurement
instrument may be
incorrect.
Please check the wiring
for VT/CT and for the
measurement instrument.
Measured values of PF
are including large error.
If the input current is
smaller than the rating,
error becomes large.
(about 5% or below of
rated current)
This is not an error, or
use it as it is, or if error
is troublesome, change
the CT according to the
actual current to be used.
Condition Possible Cause Solution
Measurement Error
The displayed active
power is different from
the active power that is
calculated by multiplying
the displayed current,
voltage, and power factor.
If the AC of the current
and voltage deteriorate
due to harmonics, it will
not be the same as the
calculated value. (For
AC without harmonics,
the calculated value will
match with the displayed
value.)
Please continue using
the instrument as it is.
The total effective
harmonics value from the
harmonic current is very
different from the current
value.
The distortion factor
(content factor) is way
over 100%. (Such as
measurement of the
inverter secondary side
output)
Please check the
measured item.
The current measured
by another measurement
instrument (such as
a clamp meter) is
different from the current
measured by this
instrument. (More than
the tolerance)
If another measurement
instrument uses the
average method
for measuring, the
measurement instrument
used will have a
larger error when the
AC deteriorates due
to harmonics. (This
measurement instrument
uses the RMS value
method.)
Please compare
the currents using a
measurement instrument
that uses the RMS value
method.
Analog output has a
large error.
If the wiring to the
receptor is long, the error
may increase.
Perform the zero and
span adjustment for
analog output.
Pulse output has a large
error.
When the pulse unit is
set to the minimum value
and the pulse width is
set to 0.500s or 1.000s,
the pulse output cannot
follow if the load is too
large, which can result in
a decrease in the pulse
output number.
Review the pulse unit or
pulse width setting
On the maximum/
minimum value display
screen, a present value
that is outside of the
maximum/minimum
range is displayed
During the starting
current delay time, the
maximum value is not
updated, so the present
value that is over the
maximum value may be
displayed.
Please continue using
the instrument as it is.
Operation
Cannot change the
settings in the setting
mode.
If SET at the bottom of
the screen is blinking,
you are in the set value
confirmation mode.
Settings cannot be
changed in this mode.
Please go to the setting
mode to change settings.
“PASS 0000” appears
when trying to change
the setting mode.
The password protection
setting is turned to valid.
Please enter the set
password. Also, the
default password is
“0000”
Other
Maximum value and
minimum value changed.
These are cleared if the
settings for the phase
wire, VT/direct voltage,
and CT primary current
are changed.
Make a note of the
values before changing
the settings.
The values of the setting
items that were not
supposed to change
have changed.
Some setting items
return to the default
values when settings for
the phase wire method,
VT/direct voltage, and
CT primary current are
changed.
Please refer to
“Initializing Related
Items by Changing
Settings” and reconfigure
the setting items that
returned to their default
values.
“PASS 0000” appears
when trying to clear the
energy or maximum/
minimum value.
The password protection
setting is turned to valid.
Please enter the set
password. Also, the
default password is
“0000”
Mitsubishi Electric Automation, Inc.

MITSUBISHI ELECTRIC AUTOMATION, INC.
500 Corporate Woods Parkway, Vernon Hills, IL 60061
Ph 847.478.2100 • Fx 847.478.2253
us.MitsubishiElectric.com/fa/en/support
January, 2016 • ©2016, Mitsubishi Electric Automation, Inc. •
Specifications subject to change without notice. • All rights reserved
AZ-Y-0734 1311
Mitsubishi Electric Automation, Inc.