Mitsubishi Electric F940 User manual

HARDWARE MANUAL
F940GOT-SWD-E/LWD-E

F940GOT-SWD-E/LWD-E
Foreword
• This manual contains text, diagrams and explanations which will guide the reader in the
correct installation and operation of the communication facilities of FX series.
• Before attempting to install or use the communication facilities of FX series this manual
should be read and understood.
• If in doubt at any stage of the installation of the communication facilities of FX series
always consult a professional electrical engineer who is qualified and trained to the local
and national standards which apply to the installation site.

F940GOT-SWD-E/LWD-E
i
F940GOT-SWD-E/LWD-E
HARDWARE MANUAL Manual number : JY992D77901
Manual revision : D
Date : February 2000

F940GOT-SWD-E/LWD-E
ii
Guidelines for the safety of the user and protection of the F940GOT-SWD-E/LWD-E
This manual provides information for the installation and use of the Graphic Operation Terminal F940GOT.
The manual has been written to be used by trained and competent personnel. The definition of such a person
or persons is as follows;
a ) Any engineer who is responsible for the planning, design and construction of automatic equipment
using the product associated with this manual should be of a competent nature, (trained and qualified
to the local and national standards required to fulfill that role). These engineers should be fully aware
of safety with regards to automated equipment.
b ) Any commissioning or service engineer must be of a competent nature, trained and qualified to the
local and national standards required to fulfill that job. These engineers should also be trained in the
use and maintenance of the completed product. This includes being completely familiar with all asso-
ciated documentation for the said product. All maintenance should be carried out in accordance with
established safety practices.
c ) All operators of the compliance product should be trained to use that product in a safe and coordi-
nated manner in compliance to established safety practices. The operators should also be familiar
with all documentation which is connected with the actual operation of the completed equipment.
Note:The term ‘completed equipment’ refers to a third party constructed device which contains or uses the
product associated with this manual.

F940GOT-SWD-E/LWD-E
iii
Note’s on the symbology used in this manual
At various times through out this manual certain symbols will be used to highlight points of information which
are intended to ensure the users personal safety and protect the integrity of the equipment. Whenever any of
the following symbols are encountered, its associated note must be read and understood. Each of the sym-
bols used will now be listed with a brief description of its meaning.
Hardware warnings
Software warnings
1 ) Indicates that the identified danger WILL cause physical and property damage.
2 ) Indicates that the identified danger POSSIBLY cause physical and property damage.
3 ) Indicates a point of further interest or further explanation.
1 ) Indicates special care must be taken when using this element of software.
2 ) Indicates a special point of which the user of the associate software element should be aware.
3 ) Indicates a point of interest or further explanation.

F940GOT-SWD-E/LWD-E
iv
Memo

F940GOT-SWD-E/LWD-E
v
CONTENTS
1. INTRODUCTION...................................................................................1-1
1.1 Outline of product................................................................................................1-2
1.2 Product configuration...........................................................................................1-8
1.3 System configuration.........................................................................................1-14
2. Installation, Wiring and General Specifications.....................................2-1
2.1 Installation of main body......................................................................................2-1
2.2 Wiring of power supply........................................................................................2-4
2.3 Functions of operation keys and connectors.......................................................2-9
2.4 Outside dimensions...........................................................................................2-12
2.5 General specificationsl ......................................................................................2-13
2.6 Connection to personal computer......................................................................2-15
2.7 CPU port connection .........................................................................................2-18
2.8 Computer link port connection (MELSEC A Series)..........................................2-26
2.9 Connection to SYSMAC C Series .....................................................................2-29
2.10 Connection to FLEX-PC N Series .....................................................................2-32
2.11 Connection by general-purpose communication ...............................................2-35
3. Startup...................................................................................................3-1
3.1 Startup procedure................................................................................................3-2
3.2 Operation environment setting ............................................................................3-5
4. Extension Module..................................................................................4-1
4.1 Data transfer adaptor...........................................................................................4-1

F940GOT-SWD-E/LWD-E
vi
5. Maintenance..........................................................................................5-1
5.1 Outline of maintenance........................................................................................5-1
5.2 Replacement of battery .......................................................................................5-3
5.3 Replacement of backlight....................................................................................5-5
6. Troubleshooting.....................................................................................6-1
6.1 Power indication ..................................................................................................6-1
7. Additional Functions (in Ver3.00 or later)..............................................7-1
7.1 Applicable Versions and Models .........................................................................7-1
7.2 Connection to MELSEC QnA Series PC.............................................................7-2
7.3 Connection to SLC 500 Series............................................................................7-3
7.4 Connection to Bar Code Reader .........................................................................7-5
7.5 Screen Hard Copy Function ................................................................................7-7
7.6 Additional Function in Alarm History Display.......................................................7-8
7.7 Specification of Ten-Key Window Initial Display Position....................................7-8
8. Additional Functions (in V3.10 or later) .................................................8-1
8.1 Applicable Versions and Models .........................................................................8-1
9. Additional Functions (in V4.00 or later) .................................................9-1
9.1 Applicable Versions and Models .........................................................................9-1
Note to User
This manual describes installation, wiring and the specifications of the F940GOT.
For handling and operating procedures of the F940GOT main body, refer to the
F940GOT Operation Manual offered separately.

INTRODUCTION 1.
1-1
1. INTRODUCTION
This section describes the product configuration and the system configuration of the graphic
operation terminal.
Confirm various functions of each unit.
F940GOT-SWD-E/LWD-E

F940GOT-SWD-E/LWD-E INTRODUCTION 1.
1-2
1.1 Outline of product
The graphic operation terminal (which may be hereafter
abbreviated as "GOT") is attached on the panel face of a
control panel or an operation panel, and connected to a
program connector in an FX or A Series programmable
controller (which may be hereafter abbreviated as "PLC")
(except the A0J2) inside the control panel.
Not only the CPU port connection method but also the
computer link port connection method is available so that
the GOT can be connected to a PLC other than MELSEC
or a micro computer board.
You can monitor various devices and change the data of
the PLC while checking the screen of the GOT.
There are several display screens built in the GOT which
offer various functions. In addition, you can create display
screens.
The built-in screens (system screens) and the screens
made by the user (user screens) have the following func-
tions respectively.
FX or
A Series PLC
Program
connector
GOT main body