Mitsubishi MXZ-8B140VA Operating manual

TECHNICAL & SERVICE MANUAL
SPLIT-TYPE, HEAT PUMP AIR CONDITIONERS
CONTENTS
1. SAFETY PRECAUTION ······································ 2
2. OVERVIEW OF UNITS········································ 5
3. SPECIFICATIONS ············································· 12
4. DATA·································································· 13
5. OUTLINES AND DIMENSIONS ························ 17
6. WIRING DIAGRAM············································ 18
7. NECESSARY CONDITIONS FOR SYSTEM CONSTRUCTION ··· 20
8. TROUBLESHOOTING······································· 22
9. ELECTRICAL WIRING ······································ 56
10. WIRING SPECIFICATIONS.······························ 58
11. SYSTEM CONTROL ·········································· 59
12. REFRIGERANT PIPING TASK·························· 61
13. DISASSEMBLY PROCEDURE·························· 64
INDOOR UNITS COMBINATION SHEETS
No. OCH480
REVISED EDITION-D
[Service Ref.]
MXZ-8B140VA
MXZ-8B160VA
MXZ-8B140YA
MXZ-8B160YA
HFC
utilized
R410A
March 2014
NOTE:
• Thisservicemanual
describestechnicaldata
ofoutdoorunit.Asfor
indoorunitsandbranch
box(OCH508),refertoits
servicemanual.
•RoHScompliantproducts
have<G>markonthespec
nameplate.
OUTDOOR UNIT
Modelname
indication
PARTS CATALOG (OCB480)
Revision:
• Addedconnectableindoorunit
 MFZ-KJ25VE,
 MFZ-KJ35VE,and
 MFZ-KJ50VEinREVISED
EDITION-D.
•Somedescriptionshave
beenmodified.
•PleasevoidOCH480
REVISEDEDITION-C.
<Outdoor unit>
[Model Name]
MXZ-8B140VA
MXZ-8B160VA
MXZ-8B140YA
MXZ-8B160YA

2
1SAFETY PRECAUTION
Cautions for units utilizing refrigerant R410A
1-1. ALWAYS OBSERVE FOR SAFETY
Use new refrigerant pipes.
Charge refrigerant from liquid phase of gas
cylinder.
If the refrigerant is charged from gas phase, composition
change may occur in refrigerant and the efficiency will be
lowered.
Do not use refrigerant other than R410A.
If other refrigerant (R22 etc.) is used, chlorine in refrige-
rant can cause deterioration of refrigerant oil etc.
Use a vacuum pump with a reverse flow check
valve.
Vacuum pump oil may flow back into refrigerant cycle and
that can cause deterioration of refrigerant oil etc.
Use the following tools specifically designed for
use with R410A refrigerant.
The following tools are necessary to use R410A refrigerant.
Handle tools with care.
If dirt, dust or moisture enters into refrigerant cycle, that can
cause deterioration of refrigerant oil or malfunction of com-
pressor.
Do not use a charging cylinder.
If a charging cylinder is used, the composition of refrigera-
nt will change and the efficiency will be lowered.
Flare tool
Electronic refrigerant
charging scale
Vacuum pump adaptor
Size adjustment gauge
Gauge manifold
Torque wrench
Gas leak detector
Charge hose
Tools for R410A
Contamination inside refrigerant piping can cause deterio-
ration of refrigerant oil etc.
If dirt, dust or moisture enters into refrigerant cycle, that can
cause deterioration of refrigerant oil or malfunction of com-
pressor.
If large amount of mineral oil enters, that can cause deterio-
ration of refrigerant oil etc.
Store the piping indoors, and both ends of the
piping sealed until just before brazing.
(Leave elbow joints, etc. in their packaging.)
Make sure that the inside and outside of refrige-
rant piping is clean and it has no contaminants
such as sulfur, oxides, dirt, shaving particles, etc,
which are hazard to refrigerant cycle.
In addition, use pipes with specified thickness.
The refrigerant oil applied to flare and flange
connections must be ester oil, ether oil or
alkylbenzene oil in a smalll amount.
Never use any refrigerant other than that specified.
Doing so may cause a burst, an explosion, or fire when the
unit is being used, serviced, or disposed of.
Correct refrigerant is specified in the manuals and on the
spec labels provided with our products.
We will not be held responsible for mechanical failure,
system malfunction, unit breakdown or accidents caused
by failure to follow the instructions.
Use the specified refrigerant only.
Ventilate the room if refrigerant leaks during
operation. If refrigerant comes into contact with
a flame, poisonous gases will be released.
1-2. CAUTIONS RELATED TO NEW REFRIGERANT
Before obtaining access to terminal, all supply
circuit must be disconnected.
OCH480D

3
Gravimeter
Unit
[3] Service tools
(1) Use the below service tools as exclusive tools for R410A refrigerant.
[2] Additional refrigerant charge
When charging directly from cylinder
·CheckthatcylinderforR410Aonthemarketissyphontype.
·Chargingshouldbeperformedwiththecylinderofsyphonstoodvertically.(Refrigerantischargedfromliquidphase.)
[1] Cautions for service
(1) Perform service after recovering the refrigerant left in unit completely.
(2) Do not release refrigerant in the air.
(3) After completing service, charge the cycle with specified amount of refrigerant.
(4) When performing service, install a filter drier simultaneously.
Be sure to use a filter drier for new refrigerant.
No. Toolname Specifications
1Gaugemanifold
·OnlyforR410A
·Usetheexistingfittingspecifications.(UNF1/2)
·Usehigh-tensionsidepressureof5.3MPa·Gorover.
2Chargehose ·OnlyforR410A
·Usepressureperformanceof5.09MPa·Gorover.
3Electronicscale
4Gasleakdetector ·UsethedetectorforR134a,R407CorR410A.
5Adaptorforreverseflowcheck ·Attachonvacuumpump.
6Refrigerantchargebase
7Refrigerantcylinder ·OnlyforR410A·Topofcylinder(Pink)
·Cylinderwithsyphon
8Refrigerantrecoveryequipment
OCH480D

4
(2) Cautions for refrigerant piping work
NewrefrigerantR410Aisadoptedforreplacementinverterseries.AlthoughtherefrigerantpipingworkforR410Aissame
asforR22,exclusivetoolsarenecessarysoasnottomixwithdifferentkindofrefrigerant.Furthermoreastheworking
pressureofR410Ais1.6timeshigherthanthatofR22,theirsizesofflaredsectionsandflarenutsaredifferent.
1Thicknessofpipes
BecausetheworkingpressureofR410AishighercomparedtoR22,besuretouserefrigerantpipingwiththickness
shownbelow.(Neverusepipesof0.7mmorbelow.)
2Dimensionsofflarecuttingandflarenut
ThecomponentmoleculesinHFCrefrigerantaresmallercomparedtoconventionalrefrigerants.Inadditiontothat,
R410Aisarefrigerant,whichhashigherriskofleakagebecauseofitsworkingpressurehigherthanthatofotherrefriger-
ants.Therefore,toenhanceairtightnessandintensity,flarecuttingdimensionofcopperpipeforR410Ahasbeenspeci-
fiedseparatelyfromthedimensionsforotherrefrigerantsasshownbelow.ThedimensionBofflarenutforR410Aalso
haspartlybeenchangedtoincreaseintensityasshownbelow.Setcopperpipecorrectlyreferringtocopperpipeflaring
dimensionsforR410Abelow.For1/2”and5/8”,thedimensionBchanges.
Usetorquewrenchcorrespondingtoeachdimension.
3ToolsforR410A(Thefollowingtableshowswhetherconventionaltoolscanbeusedornot.)
1/4
3/8
1/2
5/8
3/4
6.35
9.52
12.70
15.88
19.05
0.8
0.8
0.8
1.0
—
0.8
0.8
0.8
1.0
1.0
Nominal
dimensions(inch)
Diagram below: Piping diameter and thickness
Outside
diameter (mm)
Thickness (mm)
R410A R22
1/4
3/8
1/2
5/8
3/4
6.35
9.52
12.70
15.88
19.05
9.1
13.2
16.6
19.7
—
9.0
13.0
16.2
19.4
23.3
Nominal
dimensions (inch)
Flare cutting dimensions
Outside
diameter
Dimension A ( )
+0
-0.4
(mm)
R410A R22
(mm)
1/4
3/8
1/2
5/8
3/4
6.35
9.52
12.70
15.88
19.05
17.0
22.0
26.0
29.0
—
17.0
22.0
24.0
27.0
36.0
Nominal
dimensions (inch)
Flare nut dimensions
Outside
diameter
Dimension B (mm)
R410A R22
(mm)
Gauge manifold
Charge hose
Gas leak detector
Refrigerant recovery equipment
Refrigerant cylinder
Applied oil
Safety charger
Charge valve
Vacuum pump
Flare tool
Bender
Pipe cutter
Welder and nitrogen gas cylinder
Refrigerant charging scale
Vacuum gauge or thermis-
tor vacuum gauge and
vacuum valve
Charging cylinder
Air purge, refrigerant charge
and operation check
Gas leak check
Refrigerant recovery
Refrigerant charge
Apply to flared section
Prevent compressor malfunction
when charging refrigerant by
spraying liquid refrigerant
Prevent gas from blowing out
when detaching charge hose
Vacuum drying and air
purge
Flaring work of piping
Bend the pipes
Cut the pipes
Weld the pipes
Refrigerant charge
Check the degree of vacuum. (Vacuum
valve prevents back flow of oil and refri-
gerant to thermistor vacuum gauge)
Refrigerant charge
Tool exclusive for R410A
Tool exclusive for R410A
Tool for HFC refrigerant
Tool exclusive for R410A
Tool exclusive for R410A
Ester oil and alkylbenzene
oil (minimum amount)
Tool exclusive for R410A
Tool exclusive for R410A
Tools for other refrigerants can
be used if equipped with adap-
ter for reverse flow check
Tools for other refrigerants
can be used by adjusting
flaring dimension
Tools for other refrigerants can be used
Tools for other refrigerants can be used
Tools for other refrigerants can be used
Tools for other refrigerants can be used
Tools for other refrigerants
can be used
Tool exclusive for R410A
Tools and materials Use R410A tools Can R22 tools be used?
(Usable if equipped
with adapter for rever-
se flow)
(Usable by adjusting
flaring dimension)
Can R407C tools be used?
Ester oil:
Alkylbenzene oil: minimum amount
(Usable if equipped
with adapter for rever-
se flow)
(Usable by adjusting
flaring dimension)
: Prepare a new tool. (Use the new tool as the tool exclusive for R410A.)
: Tools for other refrigerants can be used under certain conditions.
: Tools for other refrigerants can be used.
DimensionA
DimensionB
OCH480D

5
2OVERVIEW OF UNITS
2-1. CONSTRUCTION OF SYSTEM
MXZ-8B140YA/160YA
6HP
MXZ-8B140VA/160VA
5HP
14.0
16.0
15.5
18.0
R410A
Indoor unit
that can be
connected
Branch box
that can be
connected
Capacity
Refrigerant
Rated
capacity (kW)
Cooling
Heating
Number of units
Total system wide capacity
Type 15 ~ Type 100
2 ~ 8 units
1 ~ 2 units
21 ~ 132 % of outdoor unit capacity (3.0 kW ~ 18.5 kW) 19 ~ 130 % of outdoor unit capacity (3.0 kW ~ 20.2 kW)
Number of units
Outdoor unit
Ceiling
concealed
4-way
ceiling cassette
Wall
mounted
Model type Model name
Deluxe
Standard
Compact
Low static pressure
Middle static pressure
High static pressure
2 by 2 type
Standard
MSZ-FA25/35VA
MSZ-FB25/35/50VA(H)
MSZ-FD25/35/50VA
MSZ-FH25/35/50VE
MSZ-GA22/25/35/50/60/71/80VA
MSZ-GB50VA
MSZ-GC22/25/35VA
MSZ-GC22/25/35/50/60/71NA
MSZ-GE22/25/35/42/50/60/71/80VA
MSZ-SF25/35/42/50VE
MSZ-GE22/25/35/42/50/60/71NA
MSZ-GF60/71VE
MSZ-EF18/22/25/35/42/50VE
MSZ-SF15/20VA
SEZ-KA/KC25/35/50/60/71VA
SEZ-KD25/35/50/60/71VA(L)
PEAD-RP50/60/71/100JA(L)Q.UK
PEA-RP71EA/RP100EA2
MCFZ-GA35/50/60VA
SLZ-KA25/35/50VA(L)
PLA-RP35/50/60/71AA(.UK)/BA(.UK)
PLA-RP71BA2.UK
PLA-RP100BA/BA3
MFZ-KA25/35/50VA
MFZ-KJ25/35/50VE
MLZ-KA25/35/50VA
Floor standing
Capacity class (kW)
2.2 2.5 3.5 5.0 6.0 7.1 8.0 10.0*
Connectable indoor unit lineup (Heat pump inverter type)
<NOTE> The lineup of a connectable indoor unit depends on a district/areas/country.
* When connectiing the indoor unit with the number 100, use the PAC-AK52YP-E Y-shape connection pipe (Optional part).
Branch box PAC-AK53BC
5 branches
(MAX. 5 units)
PAC-AK32BC
3 branches
(MAX. 3 units)
Number of branches
Indoor unit that
can be connected
( )
Max. 2 branch boxes can be connected to 1 outdoor unit.
According to the connection method, you can choose the favorite one.
2- branch pipe (joint) : Optional parts
In case of using 1- branch box
In case of using 2- branch boxes
No need
Model name Connection method
flare
brazing
MSDD-50AR-E
MSDD-50BR-E
Option Optional accessories of indoor units and outdoor units are available.
CAUTION : The indoor unit which rated capability exceeds
10.0kW (100 type) can NOT be connected.
2.01.5 1.8 4.2
1-way ceiling cassette
OCH480D

6
Indoor unit (Ceiling concealed type)
Indoor unit
(Wall mounted type)
Outdoor unit Branch Box
2-2. SYSTEM OUTLINE
TheadditionalconnectionoftheBranchBoxtogetherwithemploymentofthecompacttrunk-lookingoutdoorunitcan
successfullyrealizesalongdistancepipingforbighouses.Equippedwithamicroprocessor,theBranchBoxcantrans-
latethetransmissionsignalofindoorunitstoachievetheoptimumcontrol.
2-2-1. System example
2-2-2. Method for identifying
■ Outdoor unit
Model type
Power supply
V: Single phase 220/230/240V 50Hz
Y: 3-Phase 380/400/415V 50Hz
Multi type heat pump
inverter outdoor unit
Indicates equivalent to rated cooling capacity.
(O0.1kW)
Number of connectable indoor units (MAX.)
Control and refrigerant
A : New A control and R410A
Branch box (Controller)
Number of branches
5 : 5 branches
3 : 3 branches
Model type
Symbol of factory
Applicable refrigerant
A : R410A
(Indispensable)
Optional parts
M X Z – 8B140 V A
P A C – AK 5 3 BC
■ Branch box
OCH480D

7
2-3. TYPICAL COMBINATION EXAMPLE
Branch box is located INSIDE of condominium
Branch box
(Inside)
Installing branch box indoors
Only1pipingisrequiredbetweentheoutdoorand
indoorofferingafineexternalview.
Branch box (5 branch type)
Outdoor unit
SEZ-60 MSZ-35 MSZ-35 MSZ-25 MSZ-25
Living Dining Bedroom (1) Bedroom (2)
Master
bedroom
■ System example of 5 indoor units
■ Verification
Theratedcapacityshouldbedeterminedbyobservingthetablebelow.Theunit’squantitiesarelimitedin2to8units.
Forthenextstep,makesurethattheselectedtotalratedcapacityisinarangeasshownbelow.
Thetotalindoorunitcapacityshouldbewithintheoutdoorunits.
Combinationofexcessiveindoorunitsandanoutdoorunitmayreducethecapacityofeachindoorunit.
Theratedindoorcapacityisasthetablebelow.
• MXZ-8B140 3.0 ~ 18.5 kW
• MXZ-8B160 3.0 ~ 20.2 kW
Example: MXZ-8B140
Total rated capacity
18.0 18.5kW
MSZ-25 =2.5
+
+
+
+
SEZ-60 =6.0
MSZ-35 =3.5
MSZ-35 =3.5
MSZ-25 =2.5
Indoorunittype(capacityclass) 15 18 20 22 25 35 42 50 60 71 80 100
Ratedcapacity(cooling)(kW) 1.5 1.8 2.0 2.2 2.5 3.5 4.2 5.0 6.0 7.1 8.0 10.0
OCH480D

8
2-4. INSTALLATION
2-4-1. Outdoor unit installation location
 Forbestperformance,selectproperposition.
 ●Avoidplaceswherecombustiblegasmaybegeneratedorleak.
 ●Avoiddirectsunlightorothersourcesofheat.
 ●Installsunshadetoprotecttheoutdoorunitifdirectsunlighthitstheunit.
 ●Installtheoutdoorunitwithenoughdistancebetweenneighboursasoperationnoisemaydisturbtheneighbours.
 ●Avoidthepositionthattheunitiscoveredbysnoworsnowblowsdirectlyagainsttheairoutlet.Thesnowblockorblowwill
reducetheairflowoftheoutdoorunit.
Intheareasofheavysnow,specialcountermeasuresmustbetakenatinstallationtoprotecttheoutdoorunitfrommalfunc-
tioncausedbysnow.
 ●Selectalocationpermittingeasywiringandpipeaccesstothepowersourceandindoorunit.
 ●Drainwatermustbedrainedfreelyduringoperation.Checkfordraining.
2-4-2. Ventilation and service space
(1) Windy location installation
Wheninstallingtheoutdoorunitonarooftoporotherlocationunprotectedfromthewind,situatetheairoutletoftheunitso
thatitisnotdirectlyexposedtostrongwinds.Strongwindenteringtheairoutletmayimpedethenormalairflowandamal-
functionmayresult.
Thefollowingshows3examplesofprecautionsagainststrongwinds.
 ●Facetheairoutlettowardsthenearestavailablewallabout50cmawayfromthewall.(Fig.2-1)
 ●Installanoptionalairguideiftheunitisinstalledinalocationwherestrongwindsfromatyphoon,etc.maydirectlyenter
theairoutlet.(Fig.2-2)
AAirguide
 ●Positiontheunitsothattheairoutletblowsperpendicularlytotheseasonalwinddirection,ifpossible.(Fig.2-3)
BWinddirection
Fig. 2-1
Fig. 2-2 Fig. 2-3
OCH480D

9
(2) When installing a single outdoor unit
 Minimumdimensionsareasfollows,exceptforMax.,meaningMaximumdimensions,indicated.
 Refertothefiguresforeachcase.
 ●Obstaclesatrearonly(Fig.2-4)
 ●Obstaclesatrearandaboveonly(Fig.2-5)
  ·Donotinstalltheoptionalairoutletguidesforupwardairflow.
 ●Obstaclesatrearandsidesonly(Fig.2-6)
 ●Obstaclesatfrontonly(Fig.2-7)
  *Whenusinganoptionalairoutletguide,theclearanceis500mmormore.
 ●Obstaclesatfrontandrearonly(Fig.2-8)
  *Whenusinganoptionalairoutletguide,theclearanceis500mmormore.
 ●Obstaclesatrear,sides,andaboveonly(Fig.2-9)
  ·Donotinstalltheoptionalairoutletguidesforupwardairflow.
150
250
250
1500
500
Max. 500
1000
200
300
200
Fig. 2-4
Fig. 2-8Fig. 2-7
Fig. 2-5 Fig. 2-6
Fig. 2-9
unit : mm
300
1000
Max. 500
150
1000
OCH480D

10
(3) When installing multiple outdoor units
 Leave10mmspaceormorebetweentheunits.
 ●Obstaclesatrearonly(Fig.2-10)
 ●Obstaclesatrearandaboveonly(Fig.2-11)
  •Nomorethan3unitsmustbeinstalledsidebyside.Inaddition,leavespaceasshown.
  •Donotinstalltheoptionalairoutletguidesforupwardairflow.
 ●Obstaclesatfrontonly(Fig.2-12)
  *Whenusinganoptionalairoutletguide,theclearanceis1000mmormore.
 ●Obstaclesatfrontandrearonly(Fig.2-13)
  *Whenusinganoptionalairoutletguide,theclearanceis500mmormore.
 ●Singleparallelunitarrangement(Fig.2-14)
  *Whenusinganoptionalairoutletguideinstalledforupwardairflow,theclearanceis1000mmormore.
 ●Multipleparallelunitarrangement(Fig.2-15)
  *Whenusinganoptionalairoutletguideinstalledforupwardairflow,theclearanceis1500mmormore.
 ●Stackedunitarrangement(Fig.2-16)
  •Theunitscanbestackedupto2unitshigh.
  •Nomorethan2stackedunitsmustbeinstalledsidebyside.Inaddition,leavespaceasshown.
300
1500
500
1500
Max. 300
1000
600
2000
150
1500
500
1500
1500
800
150
1500
600
3000
500
Fig. 2-14Fig. 2-13
Fig. 2-12Fig. 2-11Fig. 2-10
Fig. 2-15
Fig. 2-16
unit : mm
OCH480D