Mitsubishi MELSEC-F FX1N-40MT-001 User manual

HARDWARE MANUAL
FX1N SERIES PROGRAMMABLE CONTROLLERS

FX1N Series Programmable Controllers
Foreword
• This manual contains text, diagrams and explanations which will guide the reader in the correct installation
and operation of the FX1N Series Programmable Controllers. It should be read and understood before
attempting to install or use the unit.
• Further information can be found in the FX Series Programming Manual II.
• If in doubt at any stage of the installation of an FX1N Series Programmable Controller always consult a
professional electrical engineer who is qualified and trained to the local and national standards which apply to
the installation site.
• If in doubt about the operation or use of FX1N Series Programmable Controller please consult the nearest
Mitsubisi Electric distributor.
• This manual is subject to change without notice.

i
FX1N Series Programmable Controllers
Hardware Manual
FX1N Series Programmable Controllers
Manual number : JY992D89301
Manual revision :D
Date : December 2000

FX1N Series Programmable Controllers
ii
Guidelines for the safety of the user and protection of the FX1N.
This manual provides information for the installation and use of the FX1N. The manual has
been written to be used by trained and competent personnel. The definition of such a person
or persons is as follows;
a) Any engineer who is responsible for the planning, design and construction of automatic
equipment using the product associated with this manual should be of a competent
nature, (trained and qualified to the local and national standards required to fulfill that
role). These engineers should be fully aware of all aspects of safety with regards to
automated equipment.
b) Any commissioning or service engineer must be of a competent nature, trained and
qualified to the local and national standards required to fulfill that job. These engineers
should also be trained in the use and maintenance of the completed product. This
includes being completely familiar with all associated documentation for the said
product. All maintenance should be carried out in accordance with established safety
practices.
c) All operators of the completed product should be trained to use that product in a safe
and co-ordinated manner in compliance to established safety practices. The operators
should also be familiar with documentation which is connected with the actual operation
of the completed equipment.
Note : The term ‘completed equipment’ refers to a third party constructed device which
contains or uses the product associated with this manual.

FX1N Series Programmable Controllers
iii
Note’s on the symbols used in this manual
At various times through out this manual certain symbols will be used to highlight points of
information which are intended to ensure the users personal safety and protect the integrity of
the equipment. Whenever any of the following symbols are encountered, its associated note
must be read and understood. Each of the symbols used will now be listed with a brief
description of its meaning.
Hardware warnings
Software warning
1) Indicates that the identified danger WILL cause physical and property damage.
2) Indicates that the identified danger could POSSIBLY cause physical and property damage.
3) Indicates a point of further interest or further explanation.
4) Indicates special care must be taken when using this element of software.
5) Indicates a special point which the user of the associate software element should be aware
of.
6) Indicates a point of interest or further explanation.

FX1N Series Programmable Controllers
iv
• Under no circumstances will Mitsubishi Electric be liable or responsible for any
consequential damage that may arise as a result of the installation or use of this equipment.
• All examples and diagrams shown in this manual are intended only as an aid to
understanding the text, not to guarantee operation. Mitsubishi Electric will accept no
responsibility for actual use of the product based on these illustrative examples.
• Owing to the very great variety in possible application of this equipment, you must satisfy
yourself as to its suitability for your specific application.
Associated Manuals
The following manuals are recomended as esential reference material for the correct operation
of a FX1N series Programmable Logic controller.
Manual Name Manual Number Description
FX Programming Manual II JY992D88101 Programming manual for FX1S, FX1N, FX2N and
FX2NC series Programmable Logic Controllers
FX1N-422-BD Users JY992D84101 Instruction regarding the RS422 interface board
FX1N-485-BD Users JY992D84201 Instruction regarding the RS485 interface board
FX1N-232-BD Users JY992D84401 Instruction regarding the RS232 interface board
FX1N-8AV-BD JY992D84601 Instruction regarding the variable potentiometer input
board
FX1N-CNV-BD JY992D84701 Instruction regarding the special adapter board
FX1N-5DM Users JY992D84901 Instruction regarding the display module 5DM

v
Table of Contents
Guideline ..............................................................................................ii
1. Introduction............................................................................................1-1
1.1 World Specification.............................................................................................. 1-6
1.2 Model Name ........................................................................................................ 1-7
1.3 Serial Numbers ................................................................................................... 1-8
1.4 Configuration ....................................................................................................... 1-9
1.4.1 Input/Output Points and Current Consumption ....................................................... 1-11
1.4.2 Rules of Expansion ................................................................................................. 1-13
1.5 EEPROM Back up Data .................................................................................... 1-14
2. Terminal layouts ....................................................................................2-1
2.1 AC Powered Main Units ...................................................................................... 2-1
2.2 DC Powered Main Units ...................................................................................... 2-3
2.3 FX2N and FX0N Extension blocks ....................................................................... 2-6
FX1N Series Programmable Controllers

FX1N Series Programmable Controllers
vi
3. Installation Notes...................................................................................3-1
3.1 Product Outline.................................................................................................... 3-2
3.2 FX1N RUN/STOP Control .................................................................................... 3-4
3.3 General Specifications......................................................................................... 3-5
3.4 PLC Mounting Arrangements .............................................................................. 3-6
3.5 DIN Rail Mounting ............................................................................................... 3-7
3.6 Direct Mounting .................................................................................................. 3-8
3.7 Termination at Screw Terminals........................................................................ 3-10
3.8 Wiring Techniques............................................................................................. 3-11
3.9 Installing Optional Units..................................................................................... 3-12
3.9.1 Special Function Boards ......................................................................................... 3-12
3.9.2 FX1N-5DM Display Module..................................................................................... 3-13
4. Power Supply ........................................................................................4-1
4.1 Wiring Techniques............................................................................................... 4-1
4.2 Wiring Cautions ................................................................................................... 4-1
4.3 Power Supply ...................................................................................................... 4-1
4.4 Power Requirements .......................................................................................... 4-2
4.5 Example Wiring ................................................................................................... 4-3
4.5.1 AC Power supply....................................................................................................... 4-3
4.5.2 DC Power supply....................................................................................................... 4-4
4.6 Service Power supply .......................................................................................... 4-6
4.7 Earthing / Grounding ........................................................................................... 4-6

FX1N Series Programmable Controllers
vii
5. Inputs.....................................................................................................5-1
5.1 24V DC input Specifications ................................................................................ 5-1
5.1.1 Typical Wiring............................................................................................................ 5-2
5.1.2 Input Circuit Connection ............................................................................................ 5-3
5.1.3 Diodes and Inputs Connected in Series .................................................................... 5-4
5.1.4 Resistors and Inputs Connected in Parallel .............................................................. 5-5
5.2 AC110V Input Extension Block............................................................................ 5-6
5.2.1 Input Circuit Connection ............................................................................................ 5-6
5.2.2 Programming Caution ............................................................................................... 5-7
6. Outputs..................................................................................................6-1
6.1 Output Specifications........................................................................................... 6-1
6.1.1 Relay Output Example .............................................................................................. 6-2
6.1.2 Reliability Tests ......................................................................................................... 6-3
6.1.3 Response Times ....................................................................................................... 6-3
6.1.4 Transistor Output Example........................................................................................ 6-4
6.1.5 Japanese Model Transistor Output ........................................................................... 6-4
6.2 Applying Safe Loads............................................................................................ 6-5

FX1N Series Programmable Controllers
viii
7. Diagnostics............................................................................................7-1
7.1 Preliminary Checks.............................................................................................. 7-1
7.2 ERROR LED ON (CPU ERROR) ........................................................................ 7-2
7.3 Common Errors ................................................................................................... 7-3
7.4 Maintenance ........................................................................................................ 7-3
7.5 Operation and Error Flags ................................................................................... 7-4
7.6 PLC Status Registers ......................................................................................... 7-5
7.7 Error Registers .................................................................................................... 7-6
7.8 Error Codes ......................................................................................................... 7-7
7.9 Instruction List ..................................................................................................... 7-8
7.10 Device List ........................................................................................................ 7-11

1INTRODUCTION
2TERMINALLAYOUTS
3 INSTALLATION NOTES
4 POWER SUPPLY
5 INPUTS
6OUTPUTS
7 DIAGNOSTICS
FX1N Series Programmable Controllers Introduction 1.

FX1N Series Programmable Controllers Introduction 1.

Introduction 1.
1-1
1. Introduction
This manual covers the hardware installation instructions for the FX1N Series Programmable
Logic Controller.
MODEL INPUT OUTPUT POWER
SUPPLY
DIMENSIONS
mm (inches)
WEIGHT
kg (lbs)
QTY TYPE QTY TYPE
FX1N-14MR-ES/UL 8
24V DC
Sink/
Source
6
(8)
Relay
100-240
VAC
+10%
-15%
50/60Hz
90
(3.6)
90
(3.5)
75
(3.0)
0.45
(0.99)
FX1N-24MR-ES/UL 14
(16)
10
(16)
90
(3.6)
0.45
(0.99)
FX1N-40MR-ES/UL 24 16 130
(5.2)
0.65
(1.44)
FX1N-60MR-ES/UL 36
(40) 24 175 (7.0)
0.80
(1.77)
FX1N-14MR-DS 8
24V DC
Sink/
Source
6
(8)
Relay
12V DC
-15%
to
24V DC
+20%
90
(3.6)
90
(3.5)
75
(3.0)
0.45
(0.99)
FX1N-14MT-DSS Transistor
FX1N-24MR-DS 14
(16)
10
(16)
Relay 90
(3.6)
0.45
(0.99)
FX1N-24MT-DSS Transistor
FX1N-40MR-DS 24 16 Relay 130
(5.2)
0.65
(1.44)
FX1N-40MT-DSS Transistor
FX1N-60MR-DS 36
(40) 24 Relay 175
(7.0)
0.80
(1.77)
FX1N-60MT-DSS Transistor
FX1N Series Programmable Controllers

FX1N Series Programmable Controllers Introduction 1.
1-2
Main unit outline
Please see the previous page for each units width measurement.
NX14
24V Y7
Y6
Y0
FX
1N
24M R
X0 X2
X1 X3 X5
X4 X7
X6 X11
X10
S/SX13
X12 X15
L
0V Y11
COM 2 COM 4 Y10Y5
Y4
Y2
Y1
COM 0 COM 1 COM 3 Y3
POW ER
ERROR
IN
OUT
0123
0123
RUN
4567
4567
1110
131110 12
14 15
W
W - 8 (0.31’’)
82 (3.20’’) 90 (3.54’’)
75 (2.95’’)
8 (0.31’’)
DIN rail
mounting
slot
2 - 4.5 (0.18’’)
UNITS: mm (inches)

FX1N Series Programmable Controllers Introduction 1.
1-3
Powered Extension units
MODEL INPUT OUTPUT POWER
SUPPLY
DIMENSIONS
mm (inches)
WEIGHT
kg (lbs)
QTY TYPE QTY DEVICE
FX0N-40ER-ES/UL 24
24V DC
Sink/
Source
16 Relay
100-
240VAC
+10%,
-15%
50/60Hz 150
(5.9)
90
(3.5)
87
(3.4)
0.75
(1.65)
FX0N-40ET-DSS 24 16 Transistor
(Source) 24VDC
+20%
-15%
FX0N-40ER-DS 24 16 Relay
FX2N-32ER-ES/UL 16 16 Relay 100-
240VAC
+10%,
-15%
50/60Hz
150
(5.9)
0.65
(1.4)
FX2N-32ET-ESS/UL 16 16 Transistor
(Source)
FX2N-48ER-ES/UL 24 24 Relay 182
(7.2)
0.85
(1.9)
FX2N-48ET-ESS/UL 24 24 Transistor
(Source)
100-
240VAC
+10%,
-15%
50/60Hz
FX2N-48ER-UA1/UL 24 110VAC 24 Relay 220
(8.7)
1.00
(2.2)

FX1N Series Programmable Controllers Introduction 1.
1-4
Extension blocks
MODEL
INPUT OUTPUT DIMENSIONS
mm (inches)
MASS
(WEIGHT)
kg (lbs)
QTY TYPE QTY DEVICE TYPE
FX0N-8EX-UA1/UL 8 110V AC
inputs -- -
43
(1.7)
90
(3.5)
87
(3.4)
0.2
(0.44)
FX0N-8EX-ES/UL 8 24V DC
Sink/
Source
-- -
FX0N-8ER-ES/UL 4 4 Relay -
FX0N-8EYR-ES/UL - - 8 -
FX0N-8EYT-ESS/UL - - 8 Transistor Source
FX0N-16EX-ES/UL 16
24V DC
Sink/
Source
-- -
70
(2.8)
0.3
(0.66)
FX0N-16EYR-ES/UL - - 16 Relay -
FX0N-16EYT-ESS/UL - - 16 Transistor Source
FX2N-16EX-ES/UL 16
24V DC
Sink/
Source
-- -
40
(1.6)
90
(3.5)
87
(3.4)
0.3
(0.66)
FX2N-16EYR-ES/UL - - 16 Relay -
FX2N-16EYT-ESS/UL - - 16 Transistor Source

FX1N Series Programmable Controllers Introduction 1.
1-5
*1: Internal 24V DC
*2: The value depends on the switch setting.
Special function blocks
MODEL DESCRIPTION
NUMBER
OF I/O POWER SUPPLY
DIMENSIONS
mm (inches)
MASS
(WEIGHT)
kg (lbs)
I O Internal
5V DC
External
24V DC
FX2N-2DA Digital to analog converter - 8 - 30mA 85mA*1 43
(1.7)
90
(3.5)
87
(3.4)
0.2(0.44)
FX2N-2AD Analog to digital converter - 8 - 20mA 50mA*1
FX2N-4DA Digital to analog converter - 8 - 30mA 200mA
55
(2.1) 0.3(0.66)
FX2N-4AD Analog to digital converter - 8 - 30mA 55mA
FX2N-4AD-PT PT 100 probe interface - 8 - 30mA 50mA
FX2N-4AD-TC Thermo-couple interface - 8 - 30mA 50mA
FX2N-32CCL CC-Link Interface block - 8 - 130mA 50mA
43
(1.7)
0.2(0.44)
FX2N-16LNK-M
MELSEC-I/O LINK
Remote I/O system
master block
*2 8 *2 200mA 90mA 0.5(1.1)
FX0N-3A Analog / Digital converter - 8 - 30mA 90mA*1 43
(1.7)
87
(3.4) 0.2(0.44)
FX2N-8AD Analog input block - 8 - 50mA 80mA 75
(3.0)
75
(3.0) 0.3(0.66)

FX1N Series Programmable Controllers Introduction 1.
1-6
1.1 World Specification.
Input
Sink / Source
World spec models : SINK / SOURCE.
Japanese models : ALWAYS SINK.
Outputs
Transistor
World spec models : ALWAYS SOURCE.
Japanese models : ALWAYS SINK.

FX1N Series Programmable Controllers Introduction 1.
1-7
1.2 Model Name
Notes on model name
Note:
*1. World spec FX1N DC type main units have not yet recieved official UL certification.
*1. FX0N series extension units do not have UL certification.
*2. FX0N series extension units do not have CE certification.
FX1N -24MR-DS / ¨
C)
A)
B) E)
D)
F)
A) PLC type : FX1N
B) Total number of I / O channels
C)
Unit type
M MPU - main unit
E Powered extension unit
EX Extension block, input
EY Extension block, output
D)
Output type
R Relay
TTransistor
S Triac (SSR)
E)
Features
Omit AC, Japanese spec.
D DC Japanese spec.
DS DC World spec, CE & UL registered *1.
DSS DC World spec. DC source transistor, CE & UL
registered *1.
E AC, Japanese spec.
ES AC, World spec, CE registered.
ESS AC World spec. DC source transistor, CE
registered.
UA1 AC Power Supply, AC inputs, CE registered. *2
F) UL UL registered

FX1N Series Programmable Controllers Introduction 1.
1-8
1.3 Serial Numbers
Notes on serial numbers
1) Production year
2) Production month
3) Production serial number
SERIAL NO.: 0 6 3267
3)
1)
2)
e.g.
0=2000
1=2001 1-9=Jan-Sept
X=Oct
Y=Nov
Z=Dec