Mitsubishi DX-TL1600EM User manual

1
DIGITAL RECORDER
RS-232 PROTOCOL
MODEL
DX-TL1600EM
ENGLISH
DEUTSCH

2
•
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Operations
ENGLISH
■RS-232C settings
This connection can be used for remote control and re-
cording supplementary information when the main unit is
connected to a PC.
♦Transmission speed
Example:Transmission speed is set for 4800 bps.
1.Pressthe SET UP button to display the <MENU SETTING>
menu.
2.Turn the JOG dial to move the cursor to COMMUNICA-
TION SETTING then turn the SHUTTLE ring to the right.
• The <COMMUNICATION SETTING> menu will appear.
<COMMUNICATION SETTING>
@RS-232C SETTING
TCP/IP SETTING
3. Check that the cursor is next to RS-232C SETTING and
turn the SHUTTLE ring to the right.
• The <RS-232C SETTING> menu will appear.
<RS-232C SETTING>
@TRANSMISSION RATE
DATA BIT LENGTH
PARITY BIT
STOP BIT LENGTH
DELIMITER
1200
8BIT
NONE
1BIT
CR
4. Check that the cursor is next to TRANSMISSION RATE
and turn the SHUTTLE ring to the right to flash the sub-item.
<RS-232C SETTING>
@TRANSMISSION RATE
DATA BIT LENGTH
PARITY BIT
STOP BIT LENGTH
DELIMITER
1200
8BIT
NONE
1BIT
CR
5.Turn the JOG dial to select “4800” and turn the SHUTTLE
ring to the right to finish setting.
<RS-232C SETTING>
@TRANSMISSION RATE
DATA BIT LENGTH
PARITY BIT
STOP BIT LENGTH
DELIMITER
4800
8BIT
NONE
1BIT
CR
6. Press the SET UP button.
• The <RS-232C SETTING> menu will disappear.
■TCP / IP settings
The IP address, subnet mask setting, and MAC address
used to specify the connected recorder can be referred to
here (refer to page 8).
Press the COMMUNICATION buttonontheunit’s
front face to activate the TCP/IP communication
function.
1.Pressthe SET UP button to display the <MENU SETTING>
menu.
2.Turn the JOG dial to move the cursor to COMMUNICA-
TION SETTING then turn the SHUTTLE ring to the right.
• The <COMMUNICATION SETTING> menu will appear.
<COMMUNICATION SETTING>
@RS-232C SETTING
TCP/IP SETTING
3.Turn the JOG dial to move the cursor toTCP / IP SETTING
then turn the SHUTTLE ring to the right.
•The <TCP / IP SETTING> menu will appear.
<TCP/IP SETTING>




@SELF IP ADDRESS
000.000.000.000Ł
SUBNET MASK
000.000.000.000Ł
<MAC ADDRESS>
08-00-70-2E-3F-FF

4. Check that the cursor is next to SELF IP ADDRESS and
turn the SHUTTLE ring to the right to flash the sub-item .
<TCP/IP SETTING>




@SELF IP ADDRESS
000.000.000.000Ł
SUBNET MASK
000.000.000.000Ł
<MAC ADDRESS>
08-00-70-2E-3F-FF

5.Turn the JOG dial to input the SELF IP ADDRESS and turn
the SHUTTLE ring to the right to finish setting.
<TCP/IP SETTING>




@SELF IP ADDRESS
192.168.001.100Ł
SUBNET MASK
255.255.255.000Ł
<MAC ADDRESS>
08-00-70-2E-3F-FF

6. Press the SET UP button or turn the SHUTTLE ring to the
left.
•The <TCP/IP SETTING> menu will disappear.
■Connecting with a personal computer
This connection can be used for remote control and re-
cording supplementary information when the main unit is
connected to a PC.
PleaseuseRS-232CStraightcable (9pin) to con-
nect a modem with this unit. The setting of CTS
should be set to “HIGH” or “ON”. Please refer to the
instructionmanualofamodemfordetailsaboutcon-
nection.
♦Connection via modem
Modem Modem
Personal Compu
t
RS-232C straight cable (9 pin)
phone line
1 2 3 4 5 6 7 8 910111213141516
CAMERAIN
1 2 3 4 5 6 7 8 910111213141516
CAMERAOUT
VIDEOOUT
Y/C
CLOCKADJ REC POWERON POWEROFF ALARMOUT MODEOUT CALLOUT CALLOUT GND GND GND DC5V OUT MAX30mA GND
RS-232C
ETHERNET
RESET
ON
SCSI
TERMINATION
GNDGND
16 15 14 13 12 11 10
9 8 7 6 5 4 3 2 1
ALARMIN
SCSI
OFF
♦Direct connection
Personal Computer
RS-232C crossover cable
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
CAMERAIN
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
CAMERAOUT
VIDEOOUT
Y/C
CLOCKADJ REC POWERON POWEROFF ALARMOUT MODEOUT CALLOUT CALLOUT GND GND GND DC5V OUT MAX30mA GND
RS-232C
ETHERNET
RESET
ON
SCSI
TERMINATION
GNDGND
16 15 14 13 12 11 10
9 8 7 6 5 4 3 2 1
ALARMIN
SCSI
OFF
Please use RS-232C crossover cable (9pin) to
connect a modem with a personal computer. RS -
232CCrossover cablediffersdepending onthe per-
sonal computer.
COMMUNICATION settings / Connecting to a personal computer

3
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
♦RS-232C terminal
RS-232C
1
69
5
2
3
4
5
RXD
TXD
DTR
GND
Receiving Data
Transmission Data
Data Terminal Ready
Signal Ground
Pin NO.
Letters Letters
Pin NO.
Transmition Contents Transmition Contents
6
7
8
DSR
RTS
CTS
Data Set Ready
Transmission
Requirement
Transmission Clear
♦RS-232C cable
Please use the following RS-232C Crossover cable to connect your personal computer to the Unit.
FRAME
D-SUB 9 pin (unit) D-SUB 25 pin(Personal computer)
FG
TXD
RXD
RTS
CTS
DSR
GND
DTR
1
2
3
4
5
6
7
20
RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
1) When RS-232C terminal of personal
computer is D-SUB 25 pin
D-SUB 9 pin D-SUB 9 pin
FRAMEFRAME RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
2) When Pesonal cpmputers RS-232C
terminal is D-SUB 9 pin
♦Setting the communicating mode
The settings can be made on RS-232C SETTING of the <REARTERMINAL> menu.Set the Unit and the modem or a personal
computer with same settings. Please refer to the diagram for possible setting rate.
1
2
3
4
5
TRANSMISSION
RATE
DATA BIT LENGTH
PARITY BIT
STOP BIT
DELIMITER
1200/2400/4800/
9600
8 BIT/7 BIT
NONE/ODD/EVEN
1 BIT/2 BIT
CR/CR•LF
Synchronization Name on Menu Asynchronous
1
2
3
X control
S parameter
CS-RS hamd-shake
Not available
Not available
Available
Synchronization Name on Menu
# Set other functions on the personal
computer as shown below.
Transmission rate at
the data received/
sent
Data bit length
Parity bit setting
Stop bit length
Line feed setting
Please note that the RS-232C interface (located on the back of the unit) does not function while the unit is in commu-
nication mode.
■Command code and status
Operation and setting of this unit by a personal computer is executed by command codes and error codes.
Delimeter
(sending) #1
Delimeter
(receiving) #2
Parameter 1
Parameter n
Command code
Status
Parameter 2
Parameter 1
Parameter n
Parameter 2
,,
,
• • • • • • • • • •
• • • • • • • • • •
• • • • • • • • • •
• • • • • • • • • •
1) Command : an order from a personal computer to the unit
2) Command : a reply from the unit ( indicated on a personal computer)
,,
,
#1: If you set the DELIMITER setting to "CR" on the RS-232C setting menu,
input a Carrige return code (0DH).
If you set the DELIMITER setting to "CR • LF" on the RS-232C setting menu,
input a carrige return code (0DH) and a line
****
code (0AH).
#2: If you set the DELIMITER setting to "CR" on the RS-232C setting menu,
output a Carrige return code (0DH).
If you set the DELIMITER setting to "CR • LF" on the RS-232C setting menu,
output a carrige return code (0DH) and a line
****
code (0AH).
Make sure to send commands in an interval of 0.1 second.
♦Example of Command operation
PW1
CR
RC
EX
CR
CR
Example 1) Turn the Unit on.( when DELIMITER is set to "CR" on the RS-232C setting menu)
Command from
personal computer Replied status code from uint
to a personal computer Meaning
Sending a command to turn the Unit on.
The unit received a command and executed.
The unit received a command.
Connecting to a personal computer
Command code
Connecting to a personal computer (continued)
/ Command codes

4
•
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
♦Details of the numbers
#1 : When the setting of DELIMITER on RS-232C setting display is set to CR, carriage return code (0DH) will be input. If the
setting is CR•LF, carriage return code (0DH) and line feed code (0AH) will be input.
#2 : When the setting of DELIMITER on RS-232C setting display is set to CR, carriage return code (0DH) will be output. If the
setting is CR•LF, carriage return code (0DH) and line feed code (0AH) will be output.
*: Indicates one number or a character.
Command codes (continued)
Commands Functions Status, when normal execute
PW
*
SP
PB
RP
RC
PU
*
FA
RA
PF
*
PR
*
RW
*
TR
*
AV
*
LO
*
LM
PO?
PO
*
(1)
,
*
(2)
,
*
(3)
,
*
(4)
MB
***
MB?
FD?
PS
**
(1)
,
**
(2)
POWER ON/OFF
*
: 0 ~ 1 0 : OFF 1 : ON
STOP
PLAYBACK
REVERSE PLAYBACK
RECORDING
PAUSE SETTING/RELEASE
*
: 0 ~ 1 0 : ON 1 : OFF
Forward advance
Reverse advance
Forward Speed search
*
: Playback speed(1~ 4)
[Playback] 1 :Skip 3 fields 2,3 : Skip 5 fields
4 : Skip 1 MByte
[STOP] 1 ~ 4 : Skip 2 MByte
Reverse Speed search
*
: Playback speed (1 ~ 4)
(Refer above for settings)
Rewind DDS cassette
*
: 0 ~ 1 0 : ID4 1 : ID5
Timer REC ON/OFF
*
: 0 ~ 1 0 : OFF 1 : ON
ARCHIVE ON/OFF
*
: 0 ~ 1 0 : OFF 1 : ON
LOCK ON/OFF or PASSWORD LOCK ON
*
: 0 ~ 1
0 : LOCK OFF 1 : LOCK ON or PASSWORD LOCK ON
Acquire information on status of LOCK or PASSWORD
LOCK function
Acquire information on whether password has been
registered for PASSWORD LOCK function
PASSWORD LOCK OFF
*
(1)
,
*
(2)
,
*
(3)
,
*
(4)
: Password (0 ~ 9)
Switch over playback interval to
***
: (001 ~ 008)
001 : 25F 002 : 12.5F 003 : 8.33F
004 : 6.25F 005 : 5F 006 : 4.17F
007 : 2.5F 008 : 1F
Acquire information on playback interval
Acquire information on time and date recorded on data
Move date and present time display
**
(1)
: (Horizontal)
(Display mode 1, Character size large : 00 ~ 28)
(Display mode 1, Character size small : 00 ~ 28)
(Display mode 2 or 3, Character size large : 00 ~ 28)
(Display mode 2 or 3, Character size small : 00 ~ 28)
**
(2)
: (Vertical)
(Display mode 1, Character size large : 03 ~ 26)
(Display mode 1, Character size small : 03 ~ 26)
(Display mode 2 or 3, Character size large : 01 ~ 26)
(Display mode 2 or 3, Character size small : 01 ~ 26)
RC EX
RC EX
RC EX
RC EX
RC EX
RC EX
RC EX
RC EX
RC EX
RC EX
RC EX
RC EX
(during POWER ON only)
RC EX
RC EX
(ER08 : PASSWORD input during LOCK OFF)
(ER17 is output if LO0 is input while PASSWORD
LOCK is set to ON.)
RC LM
*
*
: 0 ~ 1 0 : OFF 1 : ON
RC PO
*
*
: 0 ~ 1 0 : No password registered 1 : Password registered
RC EX
(ER16 : PASSWORD ERROR)
RC EX
RC MB
***
***
: (001 ~ 008)
(Same as playback interval shown above)
RC FD
**
(1)
,
**
(2)
,
**
(3)
,
**
(4)
,
**
(5)
,
**
(6)
**
(1)
: Day
**
(2)
: Month
**
(3)
:Year
**
(4)
: Hour
**
(5)
: Minute
**
(6)
: Second
RC EX
BASIC FUNCTIONS
VC? Acquire information on model identification code RC DX1601
IA? RC IA
**
,
**
,
**
,
**
,
**
,
**
Acquire information on MAC ADDRESS
#2
#2 #2
#2 #2
#2
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#2
#2#2
#2 #2
#2
#2
#2#2
#2#2
#2#2
#2#2
#2#2
#2#2
#2#2
#2#2
#2#2
#2#2
#2 #2
#2#2
#2#2
#1 #2#2
#2
#2
#1
#2 #2
#2 #2
#2 #2

5
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
Command codes (continued)
Commands Functions Status, when normal execute
LC
DP00
ST0
PI
CP?
PA?
PD*
PD?
EJ*
Acquire information on current position of date and
present time display
Exits MENU display
Stop the selected item on the menu to flash
Acquire information on currently displayed menu and
whether the setting is proceeding
Acquire information on the used memory of device
selected in CAPACITY REMAIN
Acquire information whether time and date information
recorded in playback picture is alarm recording
PB DEVICE setting
*: 0 ~ 2 0 : HDD 1 : ARCHIVE 2 : COPY
Acquire information on PB DEVICE setting
Ejecting media out of DEVICE
*: 1 ~ 2 1 : ARCHIVE 2 : COPY
RC LT**(1),**(2)
(Same as **(1) and **(2) of Move date and present time display)
RC EX
RC EX
RC ON**(1),*(2)
**(1) :00 ~ 69
00 : current date and time display
01 : NORMAL REC SETTING
02 :TIME DATE DISPLAY
03 :TIMER PROGRAM M-DET APPLICATION
04 :MPX DISPLAY
06 : DIFINE GROUP
07 : MENU SETTING
08 :TIME DATE ADJUST
09 : COMMUNICATION SETTING
10 : INITIAL SETUP
11 : SERVICE
12 : POWER FAILURE
13 : REAR TERMINAL
14 : RS232C SETTING
15 : DATE CLEAR SELECTION
16 : CLOCK LOCATION
17 : CAMERA TITLE
19 : SCREEN SW PATTERN
20 : SPLIT16 SCREEN SETTING
21 : SPLIT9 SCREEN SETTING
22 : SPLIT4 SCREEN SETTING
24 : SPECIAL FUNCTION MENU
25 : CALL OUT
26 :VER.UP SELECTION
29 : A-REC/M-DET SETTING
30 : DEFINE ALARM GROUP
31 : LANGUAGE SELECTION
32 : INFORMATION
36 : CONNECTED SCSI DEVICE
37 : RECORDED PERIOD
40 : MOTION
41 : SET DETECTION MASK
42 :TEST MODE
43 :TCP/IP SETTING
49 :TIME DATE SEARCH SEARCHING
50 : INDEX SEARCH SEARCHING
51 : ALARM LIST SEARCH SEARCHING
52 : SKIP SEARCH SEARCHING
53 : COPY SELECTION
54 : PASSWORD SETTING
55 : PASSWORD LOCK
58 :TIMER PROGRAM P1
59 :TIMER PROGRAM P2
60 :TIMER PROGRAM P3
64 : SEARCH SELECTION
65 :TIME DATE SEARCH
66 : INDEX SEARCH
67 : SKIP SEARCH
68 : ALARM LIST SEARCH
69 : JUMP TO START POINT
*(2) : 0 ~ 1 0 : define 1 : menu is flashing
RC CP*(1),***(2)
*(1) : selection of used memory (0 ~ 2)
0 : HDD 1 : ARCHIVE 2 : OFF
***(2) : used memory (001 ~ 100) (%)
(FFF is shown when used memory is less than 1% or
WRNG is set to OFF.)
RC PA*
*: 0 ~ 1 0 : without alarm 1 :with alarm
RC EX
RC PD*
*: 0 ~ 2 0 : HDD 1 : ARCHIVE 2 : COPY
RC EX
BASIC FUNCTIONS
#2
#2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#1
#1
#1
#1
#1
#1
#2
#2
#2 #2
#1
#1
#2 #2 #1

6
•
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
CF
**
CF?
SA?
DM
*
DM?
CH
*
FS1
CU
*
CU?
SG
*
SG?
CS
*
(1)
,
*
(2)
,
*
(3)
,
*
(4)
,
*
(5)
,
*
(6)
,
*
(7)
,
*
(8)
,
*
(9)
,
*
(10)
,
*
(11)
,
*
(12)
,
*
(13)
,
*
(14)
,
*
(15)
,
*
(16)
,
*
(17)
CS
*
(1)
?
CT
**
(1)
,
**
(2)
,
Text data
CT
**
(1)
?
SL
*
(1),
**
(2),
**
(3),
**
(4)
,
**
(5),
**
(6),
**
(7),
**
(8),
**
(9),
**
(10),
**
(11),
**
(12),
**
(13),
**
(14),
**
(15),
**
(16),
**
(17)
Split16
**
(2)
**
(3)
**
(4)
**
(5)
**
(6)
**
(7)
**
(8)
**
(9)
**
(10)
**
(11)
**
(12)
**
(13)
**
(14)
**
(15)
**
(16)
**
(17)
Split9
**
(2)
**
(3)
**
(4)
**
(5)
**
(6)
**
(7)
**
(8)
**
(9)
**
(10)
Split4
**
(2)
**
(3)
**
(4)
**
(5)
SL
*
(1)
?
The command code appointed the camera filter search
when execute the search (Use together the command
code when execute the search)
**
: 00 ~ 16 (Camera number)
00 : ALL 01 ~ 16 : Camera CH(1-16)
Acquire information on camera filter when execute the
search
Acquire information on camera number that during alarm
recording
DISPLAY MODE setting
*
: 1 ~ 6
Acquire information on DISPLAY MODE setting
Character size setting present time and display
*
: 0 ~ 1 0 : SMALL 1 : LARGE
Acquire information on character size setting for present
time and date display
CAMERA USAGE setting
*
: 0 ~ 2 0 : A 1 : B 2 : C
Acquire information on CAMERA USAGE setting
IMAGE QLTY setting
*
: 0 ~ 1 0 : HIGH 1 : NO FLICKER
Acquire information on IMAGE QLTY setting
DEFINE GROUP setting
*
(1)
: Pattern selection (0 ~ 2) 0 : A 1 : B 2 : C
*
(2)
~
*
(10)
: Status of CH1 to CH16 (0 ~ 5)
0 : invalid 1 ~ 5 : valid (priority number)
Acquire information on DEFINE GROUP setting
*
(1)
: Pattern selection (0 ~ 2) 0 : A 1 : B 2 : C
CH.TITLE setting
**
(1)
: Camera CH (01 ~ 16)
**
(2)
: Character numbers (Within 16 characters. )
Acquire information on CH.TITLE setting
**
(1)
: Camera CH (01 ~ 16)
SPLIT SCREEN SETTING
*
(1)
: Screen setting (0 ~ 6)
0 : SPLIT16 1 : SPLIT9a 2 : SPLIT9b 3 : SPLIT4a
4 : SPLIT4b 5 : SPLIT4c 6 : SPLIT4d
**
(2)
~
**
(17)
: Camera CH position (01 ~ 16)
( When
*
(1)
is set to 0, input data to
**
(2)
~
**
(17)
.
When
*
(1)
is set to 1 or 2, input data to
**
(2)
~
**
(10)
.
When
*
(1)
is set to 3, 4 ,5 or 6, input data to
**
(2)
~
**
(5)
.)
Acquire information on SPLIT SCREEN SETTING
*
(1)
: Screen setting (0 ~ 6)
0 : SPLIT16 1 : SPLIT9a 2 : SPLIT9b 3 : SPLIT4a
4 : SPLIT4b 5 : SPLIT4c 6 : SPLIT4d
RC EX
RC CF
**
**
: 00 ~ 16 (Camera number)
00 : ALL 01 ~ 16 : Camera CH(1-16)
RC SA
*
(1)
,
*
(2)
,
*
(3)
,
*
(4)
,
*
(5)
,
*
(6)
,
*
(7)
,
*
(8)
,
*
(9)
,
*
(10)
,
*
(11)
,
*
(12)
,
*
(13)
,
*
(14)
,
*
(15)
,
*
(16)
*
1)
~
*
(16)
(the corresponding camera number) :0 ~ 1
0 : No alarm recording 1 : During alarm recording
RC EX
RC DM
* *
: 1 ~ 6
RC EX
RC CZ
*
*
: 0 ~ 1 0 : SMALL 1 : LARGE
RC EX
RC CU
*
*
: 0 ~ 2 0 : A 1 : B 2 : C
RC EX
RC SG
*
*
: 0 ~ 1 0 : HIGH 1 : NO FLICKER
RC EX
RC CS
*
(1)
,
*
(2)
,
*
(3)
,
*
(4)
,
*
(5)
,
*
(6)
,
*
(7)
,
*
(8)
,
*
(9)
,
*
(10)
,
*
(11)
,
*
(12)
,
*
(13)
,
*
(14)
,
*
(15)
,
*
(16)
,
*
(17)
(Same as DEFINE GROUP setting shown above)
RC EX
RC CT
**
(1)
,
**
(2)
,Text data
**
(1)
: Camera CH (01 ~ 16)
**
(2)
: Character numbers
RC EX
RC SL
*
(1)
,
**
(2)
,
**
(3)
,
**
(4)
,
**
(5)
,
**
(6)
,
**
(7)
,
**
(8)
,
**
(9)
,
**
(10)
,
**
(11)
,
**
(12)
,
**
(13)
,
**
(14)
,
**
(15)
,
**
(16)
,
**
(17)
(Same as SPLIT SCREEN SETTING shown above.)
( When
*
(1)
is set to 0, output data to
**
(2)
~
**
(17)
.
When
*
(1)
is set to 1 or 2, output data to
**
(2)
~
**
(10)
.
When
*
(1)
is set to 3, 4 ,5 or 6, output data to
**
(2)
~
**
(5)
.)
MPX FUNCTIONS
Commands Functions Status, when normal execute
BASIC FUNCTIONS
DISPLAY MENU
#2
#2
#2
#2
#2
#2 #2
#2
#2
#2
#2
#2
#1
#1
#1
#1
#1
#1
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#1
#1
#1
#1
#2 #2
#2
#2
#2
#2
#2
#2
#1
#1
#1
#1
#1
#1
#1

7
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
Commands Functions Status, when normal execute
SQ
*
(1),
**
(2),
**
(3),
**
(4),
**
(5),
**
(6),
**
(7),
**
(8),
**
(9),
**
(10),
**
(11),
**
(12),
**
(13),
**
(14),
**
(15),
**
(16),
**
(17)
SM
*
(1),
**
(2),
**
(3),
**
(4),
**
(5),
**
(6),
**
(7),
**
(8),
**
(9),
**
(10),
**
(11)
,
**
(12),
**
(13),
**
(14),
**
(15),
**
(16),
**
(17)
SQ
*
(1)?
SM
*
(1)?
AC
*
AC?
CI
*
CI?
SW
**
SW?
PG
*
(1),
*
(2),
*
(3),
**
(4)
,
**
(5),
**
(6),
**
(7),
*
(8),
***
(9)
Displayed sequential channel setting
*
(1) : Screen setting (0 ~ 2)
0 : Single screen 1 : SPLIT4 screen 2 : SPLIT9 screen
**
(2) ~
**
(17) :
Camera CH order (01 ~ 16, 00) (00 = invalid camera)
SPLIT9
**
(2) : 00 ~ 01 00 : ab setting 01: a setting
SPLIT4
**
(2) : 00 ~ 03
00 : abcd setting 01 : abc setting 02 : ab setting 03: a setting
(When SPLIT4 screen and SPLIT9 screen is selected,set
**
(2) only.)
Displayed time of sequential channel setting
*
(1) : Screen setting (0 ~ 2)
0 : Single screen 1 : SPLIT4 screen 2 :SPLIT9 screen
**
(2) ~
**
(17) :
Displayed time of each camera (01 ~ 30)
(When SPLIT4 screen and SPLIT9 screen is selected, set
**
(2) only.)
Acquire information on displayed sequential channel
setting
*
(1) : Screen setting (0 ~ 2)
0 : Single screen 1 : SPLIT4 screen 2 : SPLIT9 screen
Acquire information on displayed time of sequential
channel setting
*
(1) : Screen setting (0 ~ 2)
0 : Single screen 1 : SPLIT4 screen 2 : SPLIT9 screen
ALARM REC CH. setting
*
:0 ~ 1 0 :ALL 1 :SEP
Acquire information on ALARM REC CH. setting
CH.TITLE setting
*
:0 ~ 2 0 :TITLE 1 :CH. NO 2 :NONE
Acquire information on CH.TITLE setting
Multiplexer screen switch setting
**
:00 ~ 09 , 80 ~ 88 ,90 ~ 96
00 : SPLIT16 01 : SPLIT9a 02 : SPLIT9b
03 : SPLIT4a 04 : SPLIT4b 05 : SPLIT4c
06 : SPLIT4d
07 :
Single screen sequential
08 : SPLIT4 screen sequential
09 : SPLIT9 screen sequential
80 ~ 88 : CH1 ~ CH9 (Single screen display)
90 ~ 96 : CH10 ~ CH16 (Single screen display)
Acquire information on Multiplexer screen switch setting
Timer program setting
*
(1) :SELECTED PATTERN (1 ~ 3)
1:P1 2 :P2 3 :P3
*
(2) :Program number(1 ~ 8)
*
(3) :Day of the week (0 ~ 8)
0:SUN 1 :MON 2 :TUE 3 : WED 4:THU
5:FRI 6 :SAT 7 :DAY 8 :SPL
**
(4) :Rec starting hour (00 ~ 23)
**
(5) :Rec starting minute (00 ~ 59)
**
(6) :Rec ending hour (00 ~ 23)
**
(7) :Rec ending minute (00 ~ 59)
*
(8) :CAMERA USAGE pattern (0 ~ 2)
0:A 1 :B 2 :C
***
(9) :Recording interval
(001 ~ 008, SKP, PWR, ARC,AEJ)
001 : 25F 002 : 12.5F 003 : 8.33F 004 : 6.25F
005 : 5F 006 : 4.17F 007 : 2.5F 008 : 1F
SKP :SKIP PWR :POWER ARC :ARCHIVE AEJ : EJECT
(When SKP, PWR, ARC or AEJ is selected, set
*
(8) to 0, 1, or 2.)
RC EX
RC EX
RC
SQ
*
(1),
**
(2),
**
(3),
**
(4),
**
(5),
**
(6),
**
(7),
**
(8),
**
(9),
**
(10),
**
(11),
**
(12),
**
(13),
**
(14),
**
(15),
**
(16),
**
(17)
(Same as Displayed sequential channel setting shown above.)
(When SPLIT4 screen and SPLIT9 is selected, only
**
(2) is output.)
RC SM
*
(1),
**
(2),
**
(3),
**
(4),
**
(5),
**
(6),
**
(7),
**
(8),
**
(9)
,
**
(10),
**
(11),
**
(12),
**
(13),
**
(14),
**
(15),
**
(16),
**
(17)
(Same as Displayed time of sequential channel setting shown
above.)
(When SPLIT4 screen and SPLIT9 is selected,
only
**
(2) is output.)
RC EX
RC AC
*
*
:0 ~ 1 0 :ALL 1 :SEP
RC EX
RC CI
*
*
:0 ~ 2 0 :TITLE 1 :CH. NO 2 :NONE
RC EX
RC SW
**
(Same as Multiplexer screen switch setting shown above.)
RC EX
MPX FUNCTIONS
TIMER PROGRAM
#2 #2
#1
#1
#2 #2
#2 #2
#2
#2 #2
#2
#1
#1
#1
#2 #2
#2 #2
#1
#1
#1
#1
#1
#1
#2 #2
#2 #2
#2
#2
#2
#2
Command codes (continued)

8
•
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
Commands Functions Status, when normal execute
DW*(1),*(2),*(3)
DW?*
CA*(1),*(2)
PM*(1),*(2)
PP*
PP?
MC***
MD
QR*
QR?
AM***
SPECIAL DW setting
*(1) :SELECTED PATTERN (1 ~ 3)
1:P1 2 :P2 3 :P3
*(2) :Start day of the week (0 : SUN ~ 6 : SAT)
*(3) :End day of the week (0 : SUN ~ 6 :SAT)
Acquire information on SPECIAL DW setting
*(1) :SELECTED PATTERN (1 ~ 3)
1:P1 2 :P2 3 :P3
Clearing timer program
*(1) :SELECTED PATTERN (1 ~ 3)
1:P1 2 :P2 3 :P3
*(2) :Program number(1 ~ 8)
Acquire information on timer program setting
*(1) :SELECTED PATTERN (1 ~ 3)
1:P1 2 :P2 3 :P3
*(2) :Program number(1 ~ 8)
SELECTED PATTERN setting
*:1 ~ 3 1 :P1 2 :P2 3 :P3
Acquire information on SELECTED PATTERN setting
REC interval setting
*** :REC MODE
(001 ~ 008)
001 : 25F 002 : 12.5F 003 : 8.33F 004 : 6.25F
005 : 5F 006 : 4.17F 007 : 2.5F 008 : 1F
(During stop)
Acquire information on REC interval setting
Recording Picture Grade (IMAGE QUALITY)
*:1 ~ 5
1:BASIC 2 :STANDARD 3 :MEDIUM
4:HIGH 5 : SUPERIOR
Acquire information on Recording Picture Grade
Alarm REC interval setting
***:
001 ~ 008
001 : 25F 002 : 12.5F 003 : 8.33F 004 : 6.25F
005 : 5F 006 : 4.17F 007 : 2.5F 008 : 1F
RC EX
RC DW*(1),*(2),*(3)
*(1) :SELECTED PATTERN (1 ~ 3)
1:P1 2 :P2 3 :P3
*(2) :Start day of the week (0 : SUN ~ 6 : SAT)
*(3) :End day of the week (0 : SUN ~ 6 :SAT)
RC EX
RC MP*(1),*(2),*(3),**4),**(5),**(6),**(7),*(8),
***(9)
*(1) :SELECTED PATTERN (1 ~ 3)
1:P1 2 :P2 3 :P3
*(2) :Program number(1 ~ 8)
*(3) :Day of the week (0 ~ 8, - )
0:SUN 1 :MON 2 :TUE 3 : WED 4:THU
5:FRI 6 :SAT 7 :DAY 8 :SPL
**(4) :Rec starting hour (00 ~ 23, - - )
**(5) :Rec starting minute (00 ~ 59,- - )
**(6) :Rec ending hour (00 ~ 23,- - )
**(7) :Rec ending minute (00 ~ 59,- - )
*(8) :CAMERA USAGE (0 ~ 2,- )
0:A 1 :B 2 :C
***(9) :Recording interval
(001 ~ 008, SKP, PWR, ARC, AEJ, - - - )
001 : 25F 002 : 12.5F 003 : 8.33F 004 : 6.25F
005 : 5F 006 : 4.17F 007 : 2.5F 008 : 1F
SKP :SKIP PWR :POWER ARC :ARCHIVE AEJ : EJECT
(–, – –, – – – is output on *(3) ~ ***(9) when no program is set)
RC EX
RC PP*
*:1 ~ 3 1 :P1 2 :P2 3 :P3
RC EX
RC MD***
***:REC MODE
(001 ~ 008)
001 : 25F 002 : 12.5F 003 : 8.33F 004 : 6.25F
005 : 5F 006 : 4.17F 007 : 2.5F 008 : 1F
RC EX
RC QR*
*:1 ~ 5
1:BASIC 2 :STANDARD 3 :MEDIUM
4:HIGH 5 : SUPERIOR
RC EX
RECORDING SET UP TIMER PROGRAM
#2#2
#2#2
#1
#1
#1
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#1
#1
#1
#1
#1
#1
#1
#2
#2
#1
#2#2

9
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
Commands Functions Status, when normal execute
AS1
AD
**
AS0
QA
*
QA?
AL
*
AL?
ES?
MS
*
MS?
MO
*
RM
CL
*
(1),
**
(2)
CL?
*
RT
*
(1),
**
(2)
RT?
Acquire information on Alarm REC interval setting
Alarm REC duration setting
**
:01 ~ 11
01 :MAN 02 :2S 03 :5S 04 :10S
05 :15S 06 :30S 07 :45S 08 :1M
09 :2M 10 :5M 11 :10M
Acquire information on Alarm REC duration setting
Alarm Recording Picture Grade (IMAGE QUALITY)
*
:1 ~ 5
1:BASIC 2 :STANDARD 3 :MEDIUM
4:HIGH 5 : SUPERIOR
Enquiry about Alarm
Recording Picture Grade setting
Pre-Alarm
Recording setting
*
:0 ~ 3 0 :OFF 1 :SHORT 2 :MEDIUM 3 :LONG
(1 ~ 3 available in STOP mode)
Acquire information on Pre-Alarm
Recording setting
Acquire information on ESTD (estimated) TIME
MOTION DETECTION setting
*
:0 ~ 1 0 :OFF 1 :ON
Acquire information on MOTION DETECTION setting
MODE OUT setting
*
:0 ~ 3
0:REC 1 :PLAY 2 :POWER 3 :REMAIN
Acquire information on MODE OUT setting
CALL OUT setting
*
(1) : 0 ~ 1 0 : HDD 1 : ARCHIVE
**
(2) : 00 ~ 11
00 : NONE 01 : FULL 02 : 2% 03 : 4%
04 : 6% 05 : 8% 06 : 10% 07 : 15%
08 : 20% 09 : 30% 10 : 40% 11 : 50%
Acquire information on CALL OUT setting
*
(1) : 0 ~ 1 0 : HDD 1 : ARCHIVE
CAPACITY REMAIN setting
*
(1) : 0 ~ 2 0 : HDD 1 : ARC 2 : NONE
**
(2) : 02, 04, 06, 08, 10, 15, 20, 30, 40, 50(%)
(When
*
(1) is set to 2, it is not necessary to input
**
(2))
Acquire information on CAPACITY REMAIN setting
RC AM
***
***
:
001 ~ 008
001 : 25F 002 : 12.5F 003 : 8.33F 004 : 6.25F
005 : 5F 006 : 4.17F 007 : 2.5F 008 : 1F
RC EX
RC AP
**
**
:01 ~ 11
(Same as Alarm REC duration setting shown above )
RC EX
RC QA
*
*
:1 ~ 5
(Same as
Alarm Recording Picture Grade shown above )
RC EX
RC AL
*
*
:0 ~ 3
0:OFF 1 :SHORT 2 :MEDIUM 3 :LONG
RC ES
***
(1),
**
(2),
**
(3)
***
(1) :Day
**
(2) :Hour
**
(3) :Minute
RC EX
RC MS
*
*
:0 ~ 1 0 :OFF 1 :ON
RC EX
RC MR
*
*
:0 ~ 3
0:REC 1 :PLAY 2 :POWER 3 :REMAIN
RC EX
RC CL
*
(1),
**
(2)
*
(1) : 0 ~ 1 0 : HDD 1 : ARCHIVE
**
(2) : 00 ~ 11
00 : NONE 01 : FULL 02 : 2% 03 : 4%
04 : 6% 05 : 8% 06 : 10% 07 : 15%
08 : 20% 09 : 30% 10 : 40% 11 : 50%
RC EX
RC RT
*
(1),
**
(2)
*
(1) : 0 ~ 2 0 : HDD 1 : ARC 2 : NONE
**
(2) : 02, 04, 06, 08, 10, 15, 20, 30, 40, 50(%)
(When
*
(1) is set to 2,
**
(2) is not output)
RECORDING SET UP
A-REC/
M-DET
REAR TERMINAL
#2 #2
#2 #2
#2
#2
#2
#2
#2
#2
#1
#1
#1
#1
#2#2
#2
#2
#2
#2
#1
#1
#1
#2 #2
#1
#1
#1
#2 #2
#2 #2
#2 #2
#2 #2
#1
#1
#1
#1
#1
#2 #2
#2 #2
#2 #2
#1
Command codes (continued)

10
•
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
Commands Functions Status, when normal execute
BZ
*
FS2
PN
PT
**
PC
MI
HM?
DH?
AM?
BR
CB
SD
**
(1),
**
(2),
**
(3)
DT
SC
**
(1),
**
(2)
TM
DF
*
FS0
DE
*
DE?
RD
*
RD?
HP
*
HP?
AW
*
AW?
MR
*
MR?
BUZZER setting
*
(1) : 0 ~ 3
0:KEY 1 :WRNG 2 :REMAIN 3 :OFF
Acquire information on BUZZER setting
Acquire current power failure number
Acquire information on power failure list
**
: power failure number (01 ~ 50)
Clearing POWER FAILURE list
Initialization of the menu (available in MAIN MENU )
(Refer to “Initializing menus” for all initialized menu.
RS-232C setting menu is also initialized when executed.)
Acquire information on MAIN HDD ELAPSED TIME
setting
Acquire information on COPY ELAPSED TIME setting
Acquire information on ARCHIVE ELAPSED TIME setting
ARCHIVE POINT RESET setting
Stop the coping, restoring
Current date setting
**
(1) : Day
**
(2) : Month
**
(3) :Year (00 ~ 30)
Acquire information on current date setting
Current time setting
**
(1) : Hour
**
(2) : Minute
Acquire information on current time setting
HDD FULL setting
*
: 0 ~ 3
0 : STOP 1 : REC•STANDBY
2 : REPEAT 3 : ALARM•PROT
Acquire information on HDD FULL setting
AUTO EJECT setting
*
: 0 ~ 1 0 : ON 1 : OFF
Acquire information on AUTO EJECT setting
ARCHIVE DATA setting
*
: 1 ~ 2 1 : ALL 2 : ALARM
Acquire information on ARCHIVE DATA setting
HDD PB REPEAT setting
*
: 0 ~ 1 0 : STOP 1 : REPEAT
Acquire information on HDD PB REPEAT setting
ARCHIVE OVERWRITE setting
*
: 0 ~ 1 0 : OFF 1 : ON
Acquire information on ARCHIVE OVERWRITE setting
FIFO/OVERWRITE MODE setting
*
:0 ~ 1 0 :OFF 1 :ON
Acquuire informatoin on FIFO/OVERWRITE MODE setting
RC EX
RC BZ
*
*
(1) : 0 ~ 3
0:KEY 1 :WRNG 2 :REMAIN 3 :OFF
RC PN
**
**
: power failure number (01 ~ 50, 00)
(00 is shown when no power failure occurs)
RC PT
**
(1),
**
(2),
**
(3),
**
(4),
**
(5)
**
(1) : Day
**
(2) : Month
**
(3) :Year
**
(4) : Hour
**
(5) : Minute
(ER08 is output when no power failure occurs)
RC EX
RC EX
RC HM
******
******
: elapsed time (000000 ~ 999999)
RC DH
******
******
: COPY elapsed time (000000 ~ 999999)
RC AM
******
******
: ARCHIVE elapsed time (000000 ~ 999999)
RC EX
RC EX
RC EX
RC TD
**
(1),
**
(2),
**
(3),
*
(4)
**
(1) : Day
**
(2) : Month
**
(3) :Year (00 ~ 30)
*
(4) : Day of the week (0 ~ 6) 0 : SUN ~ 6 :SAT
RC EX
RC TI
**
(1),
**
(2),
**
(3)
**
(1) : Hour
**
(2) : Minute
**
(3) : Second
RC EX
RC TE
*
*
(1) : 0 ~ 3
0:STOP 1 :REC•STANDBY
2:REPEAT 3 :ALARM•PROT
RC EX
RC DE
*
*
:0 ~ 1 0 :ON 1 :OFF
RC EX
RC RD
*
*
: 1 ~ 2 1 : ALL 2 : ALARM
RC EX
RC HP
*
*
: 0 ~ 1 0 : STOP 1 : REPEAT
RC EX
RC AW
* *
:0 ~ 1 0 :OFF 1 :ON
RC EX
(Only activated when the HDD is connected to ID4.)
RC MR
* *
:0 ~ 1 0 :OFF 1 :ON
(Only activated when the HDD is connected to ID4.)
REAR TERMINAL
SERVICE
INITIAL SET UP
#2 #2
#2 #2
#2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2
#2 #2
#2 #2
#2
#2
#2
#2 #2
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#2 #2
#2 #2
#1
#1
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#1
#1
#1
#1
#1
#1
#1
#1
#1
#1
#2#2
#1
#2 #2
#1

11
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
Commands Functions Status, when normal execute
Acquire information on RECORDED PERIOD of HDD
Acquire information on RECORDED PERIOD of COPY
DEVICE
Acquire information on RECORDED PERIOD of
ARCHIVE DEVICE
Acquire information on ID number of CONNECTED SCSI
DEVICE
Setting and executing COPY/RESTORE
*
(1)
: 0 ~ 3
0 : HDD COPY (COPY, OVERWRITE)
1 : HDD COPY (COPY, ADD)
2 : ARC HDD (RESTORE, OVERWRITE)
3 : COPY HDD (RESTORE, OVERWRITE)
**
(2)
: Start Day
**
(3)
: Start Month
**
(4)
: Start Year
**
(5)
: Start Hour
**
(6)
: Start Minute
**
(7)
: Start Second
**
(8)
: End Day
**
(9)
: End Month
**
(10)
: End Year
**
(11)
: End Hour
**
(12)
: End Minute
**
(13)
: End Second
<Copy up to the maximum capacity of media>
31, 12, 00, 10, 10, 10 (Start time)
FF, FF, FF, FF, FF, FF (End time)
<Copy new data to media up to its maximum capacity>
FF, FF, FF, FF, FF, F1 (Start time)
FF, FF, FF, FF, FF, F1 (End time)
RC HE
**
(1)
,
**
(2)
,
**
(3)
,
**
(4)
,
**
(5)
,
**
(6)
,
**
(7)
,
**
(8)
,
**
(9)
,
**
(10)
,
**
(11)
,
**
(12)
**
(1)
: Start Day
**
(2)
: Start Month
**
(3)
: Start Year
**
(4)
: Start Hour
**
(5)
: Start Minute
**
(6)
: Start Second
**
(7)
: End Day
**
(8)
: End Month
**
(9)
: End Year
**
(10)
: End Hour
**
(11)
: End Minute
**
(12)
: End Second
When no recording : RC HE FF, FF, FF, FF, FF, FF, FF,
FF, FF, FF, FF, FF
RC AE
**
(1)
,
**
(2)
,
**
(3)
,
**
(4)
,
**
(5)
,
**
(6)
,
**
(7)
,
**
(8)
,
**
(9)
,
**
(10)
,
**
(11)
,
**
(12)
**
(1)
: Start Day
**
(2)
: Start Month
**
(3)
: Start Year
**
(4)
: Start Hour
**
(5)
: Start Minute
**
(6)
: Start Second
**
(7)
: End Day
**
(8)
: End Month
**
(9)
: End Year
**
(10)
: End Hour
**
(11)
: End Minute
**
(12)
: End Second
When no recording : RC AE FF, FF, FF, FF, FF, FF, FF,
FF, FF, FF, FF, FF
RC RJ
**
(1)
,
**
(2)
,
**
(3)
,
**
(4)
,
**
(5)
,
**
(6)
,
**
(7)
,
**
(8)
,
**
(9)
,
**
(10)
,
**
(11)
,
**
(12)
**
(1)
: Start Day
**
(2)
: Start Month
**
(3)
: Start Year
**
(4)
: Start Hour
**
(5)
: Start Minute
**
(6)
: Start Second
**
(7)
: End Day
**
(8)
: End Month
**
(9)
: End Year
**
(10)
: End Hour
**
(11)
: End Minute
**
(12)
: End Second
When no recording : RC RJ FF, FF, FF, FF, FF, FF, FF,
FF, FF, FF, FF, FF
RC DV
*
(1)
,
***
(2)
,
*
(3)
,
***
(4)
,
*
(5)
,
***
(6)
,
*
(7)
,
***
(8)
,
*
(9)
,
***
(10)
,
*
(11)
,
***
(12)
ID0
*
(1)
:Type of DEVICE
***
(2)
: Capacity
ID1
*
(3)
:Type of DEVICE
***
(4)
: Capacity
ID2
*
(5)
:Type of DEVICE
***
(6)
: Capacity
ID3
*
(7)
:Type of DEVICE
***
(8)
: Capacity
ID4
*
(9)
:Type of DEVICE
***
(10)
: Capacity
ID5
*
(11)
:Type of DEVICE
***
(12)
: Capacity
*
(1)
,
*
(3)
,
*
(5)
,
*
(7)
,
*
(9)
,
*
(11)
: 0 ~ 3
0 : NONE 1 : HDD 2 : RDD 3 : DDS
***
(2)
,
***
(4)
,
***
(6)
,
***
(8)
,
***
(10)
,
***
(12)
: 000 ~ 103 (GB) (
Capacity shown next to unused ID number,
and Capacity of archive device and copying device is output as FFF.
)
RC EX
INFORMATION
HE?
AE?
RJ?
DV?
DB
*
(1)
,
**
(2)
,
**
(3)
,
**
(4)
,
**
(5)
,
**
(6)
,
**
(7)
,
**
(8)
,
**
(9)
,
**
(10)
,
**
(11)
,
**
(12)
,
**
(13)
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#1
#1
#1
#2
#2
#1
#2 #2
#1
COPY SELECTION
Command codes (continued)

12
•
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
TF
**
(1)
,
**
(2)
,
**
(3)
,
**
(4)
,
**
(5)
,
**
(6)
IF
***
IR
***
SF
SR
AN
AT
***
AQ?
AO?
***
AB
***
AF
****
JS
WN
CA0
VS?
VN?
TIME DATE SEARCH setting
**
(1)
: Day
**
(2)
: Month
**
(3)
:Year
**
(4)
: Hour
**
(5)
: Minute
**
(6)
: Second
INDEX SEARCH (forward) setting
***
: 001 ~ 099
INDEX SEARCH (reverse) setting
***
: 001 ~ 099
SKIP SEARCH (forward)
SKIP SEARCH (reverse)
Acquire a current alarm recording number
Acquire information on selected alarm recording
***
:
***
th alarm information on alarm list (001 ~ 800)
Acquire a current alarm recording registration number
Acquire alarm number that selected alarm recording
registration number
***
: 001 ~ 800
Searching alarm list that selected alarm recording
registration number
***
: 001 ~ 800
Searching selected alarm recording number
****
: 0001 ~ 9999
Jump to start-point
Acquire warning status
Clearing warning
Acquire information on status of video input
(During recording and when pressed the WARNING
RESET button to reset the warning, replied status code
"VS0".)
Acquire information on CH without video signal
(During recording and when pressed the WARNING
RESET button to reset the warning, replied only status
code "VN".)
RC EX2
(given when search is completed)
RC EX1
(given when search is completed)
RC EX1
(given when search is completed)
RC EX
RC EX
RC AN
****
****
: 0001 ~ 9999
RC AT
**
(1)
,
**
(2)
,
**
(3)
,
**
(4)
,
**
(5)
,
**
(6)
,
**
(7)
**
(1)
: Day
**
(2)
: Month
**
(3)
:Year
**
(4) :
Hour
**
(5)
: Minute
**
(6)
: Second
**
(7)
: Camera number (01 ~ 16)
RC AQ
***
***
: 001 ~ 800
RC AO
****
****
: 0001 ~ 9999
RC EX5
RC EX5
RC EX6
RC WN
**
,
**
,......,
**
**
: 00 ~ 11
00 : NONE
01 : HDD FULL
02 : HDD NEAR END
03 : NO SIGNAL
04 : COPY CHECK MEDIA/BACKUP CHECK MEDIA/
RESTORE CHECK MEDIA
05 : COPY SIZE ERROR/BACKUP SIZE ERROR/
RESTORE SIZE ERROR
06 : ARCHIVE FULL
07 : ARCHIVE NEAR END
08 : COPY OVERTAKE ERROR/
BACKUP OVERTAKE ERROR
09 : COPY NEAR OVERTAKE/
BACKUP NEAR OVERTAKE
10 : REC SYSTEM ERROR/COPY SYSTEM ERROR/
BACKUP SYSTEM ERROR/
RESTORE SYSTEM ERROR/SYSTEM ERROR
11 : COPY R/W ERROR/BACKUP R/W ERROR/
RESTORE R/W ERROR
RC EX
RC VS
*
*
: 0 ~ 1
0 : with Video Signal 1 : without Video Signal
RC VN
**
(1)
,
**
(2)
,
**
(3)
,
**
(4)
,
**
(5)
,
**
(6)
,
**
(7)
,
**
(8)
,
**
(9)
,
**
(10)
,
**
(11)
,
**
(12)
,
**
(13)
,
**
(14)
,
**
(15)
,
**
(16)
**
: CH without Video Signal (maximum of 16CH)
(ER08 is output when CH withoutVideo Signal)
Commands Functions Status, when normal execute
OTHERS
#2 #2
#2 #2
#2 #2
#1
#1
#1
#1
#1
#2
#2
#1
#1
#1
#2 #2
#2 #2
#2 #2
#2
#2
#2
#1
#1
#2
SEARCH SELECTION
#1
#1
#1
#1
#1
#1
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2#2
#2 #2
#2

13
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••
•
SS
(MAIN DEVICE•HDD)
SS1?
(ARCHIVE DEVICE)
Acquire the current status
Acquire the current status
RC ST00 Power off
RC ST01 during set up
RC ST02 Power on/standby mode
RC ST03 PB•Reverse speed search mode
RC ST04 PB•Forward speed search mode
RC ST05 PB•Playback mode
RC ST06 PB•Pause mode
RC ST09 RPB•Playback mode
RC ST10 RPB•Pause mode
RC ST11 REC•Recording mode
RC ST12 REC•Pause mode
RC ST13
A-REC (during standby)•Recording mode
RC ST15 A-REC (during recording)•Recording mode
RC ST17 Time date search
RC ST19 Index search (FF)
RC ST20 Index search (REW)
RC ST21 Skip search (FF)
RC ST22 Skip search (REW)
RC ST25 Character search (FF)
RC ST26 Character search (REW)
RC ST27 Alarm list search
RC ST28 Jump to start point
RC ST29 Timer REC
RC ST30 Reserve of Timer REC
RC ST31 Timer reserve error
RC ST33 Clearing device
RC ST36 Restoring
RC ST47 PRE-ALARM Recording•Standby mode
RC SS1,00 Power off
RC SS1,01 during set up
RC SS1,02 Power on/standby mode
RC SS1,03
PB•Reverse speed search mode (RDD only)
RC SS1,04 PB•Forward speed search mode (RDD only)
RC SS1,05 PB•Playback mode
RC SS1,06 PB•Pause mode
RC SS1,09 RPB•Playback mode
RC SS1,10 RPB•Pause mode
RC SS1,17 Time date search
RC SS1,19 Index search (FF)
RC SS1,20 Index search (REW)
RC SS1,21
Skip search (FF) (RDD only)
RC SS1,22 Skip search (REW) (RDD only)
RC SS1,25 Character search (FF)
RC SS1,26 Character search (REW)
RC SS1,27 Alarm list search
RC ST1,28 Jump to start point
RC SS1,29 Timer REC
RC SS1,30 Reserve of Timer REC
RC SS1,31 Timer reserve error
RC SS1,33 Initializing device
RC SS1,34 Archiving
RC SS1,36 Restoring
RC SS1,46 Rewinding (DDS only)
Commands Functions Status, when normal execute
OTHERS
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2
#2
#2
#2
#2
#2
#1
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2
#2
#2
#2
#2
#2
#1
#2
#2
#2
#2
#2
#2
#2
#2
#2#2
Command codes (continued)

14
•
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
ENGLISH
SS2?
(Copy device)
DC
*
BT
**
BT?
Acquire the current status
Operation on DEVICE CHECK menu
*
: 0 ~ 1 0 : PWR-OFF 1 : CONFIG/INITIALIZE
Boot-up delay setting
**
: Second (00 ~ 99)
Acquire information on boot-up delay setting
RC SS2,00 Power off
RC SS2,01 during set up
RC SS2,02 Power on/standby mode
RC SS2,03
PB•Reverse speed search mode (RDD only)
RC SS2,04 PB•Forward speed search mode (RDD only)
RC SS2,05 PB•Playback mode
RC SS2,06 PB•Pause mode
RC SS2,09 RPB•Playback mode
RC SS2,10 RPB•Pause mode
RC SS2,17 Time date search
RC SS2,19 Index search (FF)
RC SS2,20 Index search (REW)
RC SS2,21
Skip search (FF) (RDD only)
RC SS2,22 Skip search (REW) (RDD only)
RC SS2,25 Character search (FF)
RC SS2,26 Character search (REW)
RC SS2,27 Alarm search
RC ST2,28 Jump to start point
RC SS2,29 Timer REC
RC SS2,30 Reserve of Timer REC
RC SS2,31 Timer reserve error
RC SS2,33 Initializing media of device
RC SS2,34 copying
RC SS2,36 Restoring
RC SS2,46 Rewinding (DDS only)
RC EX
RC EX
RC BT
**
**
: Second (00 ~ 99)
Commands Functions Status, when normal execute
OTHERS
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2 #2
#2
#2
#2
#2
#2
#2
#1
#2#2
#1
#2 #2
#2 #2
#2 #2
#1
#1

15
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Command Codes
Error code Meaning of error
ER00
ER01
ER02
ER03
ER04
ER05
ER06
ER07
ER08
ER09
ER10
ER11
ER12
ER13
ER14
ER15
ER16
ER17
No power supply
–
–
–
–
WARNING ERROR
Present time or Timer program has not been set
Alarm recording underway
Unfeasible (NAK)
–
Incorrect command
Incorrect parameter
Overflow on receiver
Data was not received
–
Data clearing underway (Command not accepted)
PASSWORD ERROR
PASSWORD LOCK is set
Status code Meaning of status
CE
**
DC
*
given when error occurred during copy/restore
**
: Error code (02 ~ 04)
02 : Copy/restore size error
03 : Copy/archive/restore R/W error
04 : Copy/restore media error
given when DEVICE CHECK menu appears
*
: 0 ~ 2
0 : Select PWR-OFF, CONFIG
1 : Select PWR-OFF, INITIALIZE
2 : Only PWR-OFF
Table of Error Code Table of Status Code
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
#2
DI
*
WN?
Initializing the disk
*
: 0 ~ 2
0
: HDD 1 : ARCHIVE 2 : COPY
Acquire warning status for serviceman
RC EX
RC WN
**
,
**
,......,
**
**
: 00 ~ 16 ( MAX )
00 : NONE
01 : OVERTAKE ERROR
02 : HDD R/W ERROR
03 : DEVICE R/W ERROR
06 : NO SIGNAL
07 : SUB MICRO COMPUTER HANG UP
08 : TEMPERATURE SENSOR ERROR
09 : SYSTEM ERROR
11 : STOPPING THE FUN ERROR
12 : SYSTEM RE-STARAT
13 : FLASH MEMORY ERROR
14 : REC SYSTEM ERROR
Commands Functions Status, when normal execute
SPECIAL FUNCTION MENU
#2
#2
#1
SPECIAL FUNCTION MENU
#2
#1 #2
Command codes (continued)

16
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Character Search
ENGLISH
■Character Search
Characters can be added to both visuals and audio using a PC when the unit is connected to a PC via the RS-232C interface.
These characters will appear on screen during playback. (There is also the possibility that the characters will not be displayed.)
In addition, searches of images incorporating these characters, a process called Character Search, can also be performed.
Searches are carried out by designating the characters associated with a particular image.
♦Character Search commands
Do not display characters on-screen (Playback only)
Display characters on-screen (Playback only)
Acquire information on character display settings
Acquire information on recalled display settings (Playback only)
Clear character display
Record character sets
**
: Camera number 01-16
CR0
#1
CR1
#1
CR?
#1
CM?
#1
CM
**
#1
CC
#1
CW
**
, Text data
(Up to 48 characters)
#1
RC
#2
EX
#2
RC
#2
EX
#2
RC
#2
CR
*
#2
#2
RC EX4
#2
RC CM
**
,Text data
**
: Character count (01-48)
(Text data up to 48 characters)
#2 #2
Create sets of written characters
**
:Character count (01-48)
(1)
Forward character search (During stop, pause, playback)
**
: Character count (01-48)
Abridged search by
✽ code
Searches can be made using only a specified number of characters
found at the head of recorded comments.
Reverse character search (During stop, pause, playback)
**
: Character count (01-48)
Abridged search by
✽ code
Searches can be made using only a specified number of characters
found at the head of recorded comments.
(Reply at the completion of search)
(
*
: 0-1) 0 : OFF 1 : ON
Commands Functions Status,when normal execute
LF
**
, Text data
(Up to 48 characters)
#1
LR
**
, Text data
(Up to 48 characters)
#1
RC
#2
EX
#2
RC
#2
EX
#2
RC
#2
EX
#2
#2
RC EX4
#2
(Reply at the completion of search)
♦Characters can be used
Alphabet
ASCII code
ASCII code
ASCII code
Character
Number
ABCDEFG UVWXYZ HIJKLMNO
65 66 67 68 69 70 71 72 73 74
32 37 40 41 45 46 47 58 60 62
48 49 50 51 52 53 54 55 56 57
75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90
PQRS T
%> ()
1234567 98
0
-./:
<
#2
#2: a space
Character Search

17
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Character Search
♦Sample operation
1) Record characters “ABCDEF” and images simultaneously at the camera CH number 5.
(On the RS-232C settings screen, set DELIMITER to “CR”.)
The following are the two steps required for recording characters:
1Set the character (or characters string) to be recorded;
2Record the selected character(s).
By using the CM command, characters which have been set once can be recorded any number of times.To record a different
character set, use the CW command.
CR means a carriage return code (0DH).
The unit received a command and executed.
The unit executed a command.
CW06,ABCDEF
CR
CR
CM05
CR CR
RC EX
CR CR
RC EX
Command from personal computer Replied status code from unit
to a personal computer Meaning
Sending a command for setting "ABCDEF" .
Sending a command to record set characters at the camera
CH number 5(it is able to execute while recording).
• Set the CH.TITLE setting to “NONE” to display characters during segmented display mode.
2)Search forthe scene associatedwith the recordedcharacter set“ABCDEF”. (On theRS-232C settings screen,set DELIMITER
to “CR”.)
CR
Command from personal computer Replied status code from unit
to a personal computer Meaning
Sending a command for serching "ABCDEF" by character
search in a direction of the time being.
The unit received a command and executed.
means a carriage return code (0DH).
The unit received a command and executed.
Display characters on-screen (Playback only).
LF06,ABCDEF CR
CR CR
RC EX4
CR1 CR
CR CR
RC EX
3)Searchfor thescene associatedwiththe recordedcharacter set“ABCDEFG”.(On theRS-232Csettingsscreen,set DELIMITER
to “CR”.)
By using abridged search by ✽code, search can be made using only a specified number of characters found at the head of
recorded characters.
For the recorded characters “ABCDEFG” ,searches can be made using any of the following patterns specified for number of
character data.
Example of commands : LF02,A ✽ / LF03,AB ✽/ LF04,ABC ✽/ LF05,ABCD ✽ / LF06,ABCDE ✽ / LF07,ABCDEF ✽
CR
Command from personal computer Replied status code from unit
to a personal computer Meaning
Sending a command for serching "ABC ✽" by abridged
search by ✽ code in a direction of the time being.
The unit received a command and executed.
means a carriage return code (0DH).
The unit received a command and executed.
Display characters on-screen (Playback only).
LF04,ABC ✽CR
CR CR
RC EX4
CR1 CR
CR CR
RC EX
• Character searches can only be performed during stop, pause, and playback modes.
• The unit will fast forward or rewind until it finds the character string, then shift into still frame mode.
• If the unit does not find the character string, it will stop automatically.
• When there are multiple instances of the same character string, repeat character search if the retrieved image is not the
desired image.
• Character searches may be time-consuming as the process involves searching through all the data.
• Forward searching is the only option available when using a DDS device for playback.
Character Search (continued)

1
DIGITALER REKORDER
RS-232 PROTOKOLL
MODELL
DX-TL1600EM
DEUTSCH

2
•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Betriebsvorgänge
DEUTSCH
■RS-232C einstellen
DieserAnschlußkannfürFernsteuerungundzurAufzeichnung
zusätzlicher Informationen verwendet werden, wenn das
Hauptgerät an einen Computer angeschlossen ist.
♦Übertragungsgeschwindigkeit
Beispiel: Übertragungsgeschwindigkeit auf 4800 bps
einstellen.
1. Drücken Sie die Taste SET UP, um die Anzeige <HAUPT-
MENÜ> aufzurufen.
2. Bringen Sie den Cursor mit dem JOG-Rad zur Option RS-
232 / TCP/IP EINST. und drehen Sie dann das SHUTTLE-
Rad nach rechts.
• Das Menü <RS-232 /TCP/IP EINST.> wird jetzt angezeigt.
<RS-232 / TCP/IP EINST.>
@RS-232C-EINSTELLUNG
TCP/IP-EINSTELLUNG

3.VergewissernSie sich,daß derCursorbeiderOption RS-232C-
EINSTELLUNGsteht.DrehenSiedasSHUTTLE-Radnachrechts.
• Das Menü <RS-232C-EINSTELLUNG> wird jetzt angezeigt.
<RS-232C-EINSTELUNG>
@ÜBERTRAGUNTSRATE 1200
DATENBIT-LÄNGE 8BIT
PARITÄTSBIT KEINS
STOPPBIT-LÄNGE 1BIT
PROTOKOLLE CR
4. Vergewissern Sie sich, daß der Cursor bei der Option
ÜBERTRAGUNTSRATEsteht.DrehenSiedas SHUTTLE-Rad
nach rechts, bis der Parameter anfängt zu blinken.
<RS-232C-EINSTELUNG>
@ÜBERTRAGUNTSRATE 1200
DATENBIT-LÄNGE 8BIT
PARITÄTSBIT KEINS
STOPPBIT-LÄNGE 1BIT
PROTOKOLLE CR
5. Wählen Sie mit dem JOG-Rad den Wert „4800“ aus und
drehen Sie dann das SHUTTLE-Rad nach rechts, um die
Einstellung einzugeben.
<RS-232C-EINSTELUNG>
@ÜBERTRAGUNTSRATE 4800
DATENBIT-LÄNGE 8BIT
PARITÄTSBIT KEINS
STOPPBIT-LÄNGE 1BIT
PROTOKOLLE CR

6. Drücken Sie die Taste SET UP.
• Das Menü <RS-232C-EINSTELLUNG> wird jetzt angezeigt.
■TCP / IP einstellen
HierkannaufdieIP-Adresse, dieEinstellungderHilfsnetzmaske
und die zur Bezeichnung des angeschlossenen Rekorders
verwendete MAC-Adresse Bezug genommen werden (siehe
Seite 8).
Drücken Sie dieTaste COMMUNICATION an der
Vorderseite dieses Gerätes, um die TCP/IP-
Kommunikationsfunktionzu aktivieren.
1. Drücken Sie die Taste SET UP, um die Anzeige <HAUPT-
MENÜ> aufzurufen.
2. Bringen Sie den Cursor mit dem JOG-Rad zur Option RS-
232 / TCP/IP EINST. und drehen Sie dann das SHUTTLE-
Rad nach rechts.
• Das Menü <RS-232 /TCP/IP EINST.> wird jetzt angezeigt.
<RS-232 / TCP/IP EINST.>
@RS-232C-EINSTELLUNG
TCP/IP-EINSTELLUNG

3. Bringen Sie den Cursor mit dem JOG-Rad zur Option TCP/IP-
EINSTELLUNG und drehen Sie dann das SHUTTLE-Rad nach
rechts.
• Das Menü < TCP/IP-EINSTELLUNG > wird jetzt angezeigt.
<TCP/IP-EINSTELLUNG>




@EIGENE IP-ADRESSE
000.000.000.000Ł
SUB-NETZ-MASKE
000.000.000.000Ł
<MAC-ADDRESSE>
08-00-70-2E-3F-FF

4. Vergewissern Sie sich, daß der Cursor bei der Option
EIGENE IP-ADRESSE steht. Drehen Sie das SHUTTLE-Rad
nach rechts, bis der Parameter anfängt zu blinken.
.
<TCP/IP-EINSTELLUNG>




@EIGENE IP-ADRESSE
000.000.000.000Ł
SUB-NETZ-MASKE
000.000.000.000Ł
<MAC-ADDRESSE>
08-00-70-2E-3F-FF
5. Drehen Sie den JOG-Ring, um EIGENE IP-ADRESSE
einzugeben, und drehen Sie dann den SHUTTLE-Ring nach
rechts, um die Einstellung zu beenden.
<TCP/IP-EINSTELLUNG>




@EIGENE IP-ADRESSE
192.168.001.100Ł
SUB-NETZ-MASKE
255.255.255.000Ł
<MAC-ADDRESSE>
08-00-70-2E-3F-FF
6. Drücken Sie die Taste SET UP.
• Das Menü <TCP/IP-EINSTELLUNG> wird jetzt angezeigt.
■PC-Anschluß einrichten
Wenn das Gerät über diese Schnittstelle an einen PC
angeschlossen ist, kann es über den PC gesteuert und
zusätzliche Informationen können aufgezeichnet werden.
Verwenden Sie für den Anschluß dieses Gerätes
mitderRS-232C-Schnittstelle bitte das gerade Kabel
(9-polig). Die Option CTS sollte für die Einstellung
„HOCH“oder„AN“konfiguriertwerden.Fürdetaillierte
InstruktionenkonsultierenSiebittedasHandbuchdes
Modem-Herstellers.
♦Modem-Anschluß
Modem Modem
PC
RS-232C-Kabel (9-polig)
Telefonanschluß
12345678 910111213141516
CAMERAIN
12345678 910111213141516
CAMERAOUT
VIDEOOUT
Y/C
CLOCKADJ REC POWERON POWEROFF ALARMOUT MODEOUT CALLOUT CALLOUT GND GND GND DC5V OUT MAX30mA GND
RS-232C
ETHERNET
RESET
ON
SCSI
TERMINATION
GNDGND
16 15 14 13 12 11 10
9 8 7 6 5 4 3 2 1
ALARMIN
SCSI
OFF
♦Direktanschluß
PC
RS-232C-Kabel (9-polig)
1 2 3 4 5 6 7 8 910111213141516
CAMERAIN
1 2 3 4 5 6 7 8 910111213141516
CAMERAOUT
VIDEOOUT
Y/C
CLOCKADJ REC POWERON POWEROFF ALARMOUT MODEOUT CALLOUT CALLOUT GND GND GND DC5V OUT MAX30mA GND
RS-232C
ETHERNET
RESET
ON
SCSI
TERMINATION
GNDGND
16 15 14 13 12 11 10
9 8 7 6 5 4 3 2 1
ALARMIN
SCSI
OFF
Verwenden Sie für die Verbindung vom Modem
zum PC bitte das RS-232C-Verbindungskabel (9-
polig). Die RS-232C-Verbindungskabel können von
PC zu PC verschieden sein.
Kommunikationseinstellungen / PC-Anschlüsse

3
••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••• Befehlscode
♦RS-232C-Anschluß
RS-232C
1
69
5
2
3
4
5
RXD
TXD
DTR
GND
6
7
8
DSR
RTS
CTS
Daten empfangen
Übertragung Daten
Endgerät betriebsbereit
Betriebserde
Nr. Pol
Bezeich
-nung
Nr. Pol
Funktion Funktion
Betriebsbereitschaft
Sendeteil
einschalten
Sendebereitschaft
Bezeich
-nung
♦RS-232C-Kabel
Verwenden Sie bitte das folgende RS-232C-Anschlußkabel, um das Gerät an einen PC anzuschließen.
FRAME FG
TXD
RXD
RTS
CTS
DSR
GND
DTR
1
2
3
4
5
6
7
20
RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
D-SUB 9-polig (Digital Rekorder) D-SUB 25-polig (PC)
1) Für PC-RS-232C-Schnittstelle
vomTyp D-SUB 25-polig
Steckerbelegung
FRAMEFRAME RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
RXD
TXD
DTR
GND
DSR
RTS
CTS
2
3
4
5
6
7
8
D-SUB 9-polig D-SUB 9-polig
2) Für PC-RS-232C-Schnittstelle
vomTyp D-SUB 9-polig
Steckerbelegung
♦Übertragungssystem
Die Einstellungen können in RS-232C-EINSTELLUNG im Menü <RÜCKTERMINAL EINST.> vorgenommen werden.Nehmen
Sie die notwendigen Einstellungen am Gerät und am Modem bzw.am PC vor.Detaillierte Informationen über die Einstellungen
und die Übertragungsgeschwindigkeit finden Sie in der Abbildung.
1
2
3
4
5
ÜBERTAGUMTSRATE
DATENBIT--LÄNGE
PARITÄTSBIT
STOPPBIT-LÄNGE
PROTOKOLLE
1200/2400/4800/
9600
8 BIT/7 BIT
KEINS/UNGERADE/GERADE
1 BIT/2 BIT
CR/CR-LF
1
2
3
Synchronisation Menüname
Asynchronous
X-Steuerung
S-Paramerter
CS-RS-Handshake
nicht vorhanden
nicht vorhanden
vorhanden
Synchronisation Menüname
# Stellen Sie andere Funktionen werden am PC
wie folgt ein (siehe unten).
Übertragungsge
schwindigkeit der
gesendeten/
empfangenen Daten
Bitlänge
Paritätsbit
Stoppbitlänge
Zeilenvorschub
Bitte beachten Sie, daß die RS-232C-Schnittstelle (an der Rückseite des Gerätes) nicht funktioniert, wenn das Gerät
im Kommunikationsmodus ist.
■Befehlscode und Befehlsstatus
Der Betrieb und die Einstellung des Gerätes durch einen PC werden mit Hilfe von Befehls- und Fehlercodes durchgeführt.
,,
,
• • • • • • • • • •
• • • • • • • • • •
• • • • • • • • • •
• • • • • • • • • •
,,
,
Begrenzung
(gesendet) #1
Begrenzung
(empfangen) #2
Parameter 1
Parameter n
Befehlscode
Status
Parameter 2
Parameter 1
Parameter n
Parameter 2
1) Befehl:eine Anweisung von einem PC zum Digital-Rekorder
2) Befehl:eine Antwort vom Digital-Rekorder (auf dem PC angezeigt)
#1: Bei Einstellung im RS-232C-Einstellungsmenü von PROTOKOLLE auf „CR“
wird der Befehl Carriage Return code (0DH) eingegeben.
Bei Einstellung im RS-232C-Einstellungsmenü von PROTOKOLLE auf
„CR-LF“ wird der Befehl Carriage Return code (0DH) und Linie
****
(0AH) eingegeben.
#2: Bei Einstellung im RS-232C-Einstellungsmenü von PROTOKOLLE auf „CR“ wird de
r
Befehl Carriage Return code (0DH) ausgegeben.
Bei Einstellung im RS-232C-Einstellungsmenü von PROTOKOLLE auf „CR-LF“
wird der Befehl Carriage Return code (0DH) und Linie
****
(0AH) ausgegeben.
Beachten Sie bitte, daß die Befehle in Intervallen von 0.1 Sekunde gesendet werden.
♦Beispiel einer Befehlssteuerung
PW1
CR
RC
EX
CR
CR
Beispiel 1) Schalten Sie den Digital-Rekorder an.(wenn für PROTOKOLLE im RS-232C-Einstellungsmenü
die Einstellung „CR“ gewählt wurde)
Befehl vom PC Statuscode-Antwort vom
Digital-Rekorder an den PC Bedeutung
Sendet den Befehl zum Anschalten des Digital-Rekorders.
Der Digital-Rekorder hat einen Befehl erhalten und ausgeführt.
Der Digital-Rekorder hat einen Befehl erhalten.
Connecting to a personal computer
PC-Anschlüsse (Fortsetzung)
/ Befehlscode