Mocka Boston Cot User manual

WARNING: TO PREVENT FALLS, THE MATTRESS BASE OF THIS COT
SHOULD BE ADJUSTED TO THE LOWEST POSITION BEFORE THE CHILD
CAN SIT UP
Hardware Supplied
D E
Foot Pads
x 6
Allen Key
x 1
Bolt
x 4
Bolt
x 4
Bolt
x 8
Ensure the cot is placed at a reasonable distance from curtains, blinds, heaters and power points.
Keep all medications, string, elastic, small toys or small items, such as money, out of reach from
any position in the cot.
Assembly
Care must be taken when attaching sides. Do not over-tighten screws as this can cause damage
to the cot.
Care and Maintenance
Regularly check all screws for tightness or damage that could render the cot unsafe.
To clean - use a damp cloth, avoiding the use of detergents or abrasives.
Recommended mattress size
This cot has been manufactured for use with a mattress which measures 1300mm long x 690mm
wide x 100mm in thickness. The width and length are specified because it is important that gaps
between the mattress and the sides and ends of the cot will not exceed 40mm. This is to minimize
the risk of a child’s limb becoming caught in the gap. The thickness of the mattress has been
specified to ensure that the depth of the cot is greater than 500mm with the mattress base in the
lower position to minimize the risk of a child climbing or falling out of the cot.
C Allen Key 1pc
A
B
C
Boston Cot
Assembly Instructions
Thank you for your purchase.
Please follow the manufacturers assembly instructions
in detail to ensure the safety features of the cot are not
compromised.
1
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558

12
Boston Cot
2
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Assembly Instructions
Find one of the side panels and attach to both end panels of the cot
using 4x screws (A) in the holes as shown. Insert 4x screws (C) in the
holes as shown. Tighten with the Allen key (D)
A
A
A
A
A
D
C
C
C
C
A
A
A
C
C
E
E
E
E
E
E
C
C
Find one of the side panels and attach to both end panels of the cot
using 4x screws (A) in the holes as shown. Insert 4x screws (C) in the
holes as shown. Tighten with the Allen key (D). Attach 6 x foot pads
(E) to panels [1] and [2].
A
A
D
1
2

34
Boston Cot
3
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Assembly Instructions
Attach the cot base at the required level using 4x screws (B) as shown,
and tighten with the Allen key (D).
B
B
B
B
B
D
Slide the remaining side panel into place and attach using 4x screws
(A) in the holes as shown. Tighten with the Allen key (D).
A
A
A
A
DA

56
Boston Cot
4
mocka.co.nz | mocka.com.au | PO BOX 6171, Maroochydore BC, QLD, 4558
Assembly Instructions
All done! Regularly check all screws are suitably tightened. Place the
correct size mattress into the cot before use. To clean use a damp
cloth, avoiding the use of detergents or abrasives. Once assembled lift
furniture into place, do not drag.
To adjust the base setting, remove the C screws from the end panels
and repeat steps 2 and 3 by removing the side panel and moving the
base to the corresponding hole. Securely attach again in the adjusted
position.
B
B
B
B