Modern Flames Landscape Pro Slim Series Operating instructions

SERIAL NUMBER:________________________________________
Landscape Pro Slim Series
LPS-4414 • LPS-5614 • LPS-6814 • LPS-8014 • LPS-9614
INSTALLATION/OWNERS MANUAL
FOR USE IN UNITED STATES AND CANADA

2
USER INSTRUCTIONS
LANDSCAPE PRO SERIES SLIM
LPS-4414 • LPS-5614 • LPS-6814 • LPS-8014 • LPS-9614
SAFETY INFORMATION AND OPERATIONS MANUAL
Read these instructions completely before beginning installation. Failure to follow them could
cause a heater malfunction resulting in serious injury and/or property damage.
WARNING: All electric heaters have hot and arcing or sparking parts inside. Do not use it in
areas where gasoline, paint or ammable liquids are or are stored.
This replace meets the construction and safety standards of H.U.D. for application in
manufactured homes when installed according to these instructions.
INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

3
USER INSTRUCTIONS
TABLE OF CONTENTS
When using electrical heaters, basic
precautions should always be followed to
reduce the risk of re, electric shock and injury
to persons, including the following:
1. Read all instructions before installing or
using this heater.
2. This heater is hot when in use. To avoid
burns, do not let bare skin touch hot
surfaces. Keep combustible materials,
such as furniture, pillows, bedding, papers,
clothes, and curtains at least 3 feet (0.9m)
from the front of the heater and keep them
away from the sides and rear.
3. Extreme caution is necessary when any
heater is used by or near children or
disabled people and whenever the heater is
left operating and unattended.
4. Do not operate any heater after it
malfunctions, has been dropped, or
damaged in any manner. Disconnect power
at service panel and have heater inspected
by an authorized technician or a reputable
electrician before using.
5. Do not use outdoors.
6. To disconnect heater, turn controls to o󰀨
and turn o󰀨 power to heater circuit at main
disconnect panel.
7. Do not insert or allow foreign objects to
enter any ventilation or exhaust opening as
this may cause an electric shock or re, or
damage the heater.
8. To prevent a possible re, do not block air
intakes or exhaust in any manner.
9. A heater has hot and arcing or sparking
parts inside. Do not use it in areas where
gasoline, paint or ammable vapors or
liquids are used or stored.
10.Use this heater only as described in this
manual. Any other use not recommended
by the manufacturer may cause re, electric
shock or injury to persons.
11. SAVE THESE INSTRUCTIONS
WARNING: Improper installation,
adjustment, alteration, service or
maintenance can cause injury or property
damage. Refer to this manual. For
assistance or additional information,
consult a qualied installer.
CAUTION: Do not expose the heater to the
elements (such as rain, etc).
Do not place clothing or other ammable
material on or near rebox. Never place
any objects on the replace.
Carefully supervise young children when
they are in the room with replace.
Fireplace becomes very hot when running.
Keep children and adults away from
hot surfaces to avoid burns or clothing
ignition. Fireplace will remain hot for a
time after shutdown. Allow surfaces to
cool before touching.
CAUTION: In order to avoid
overheating, do not cover the
heater.
IMPORTANT INSTRUCTIONS
Important Instructions 3
Power Data 4
Product Guide 4
Box Contents 5
Installation 6
Operation 9
Service Parts 10
Troubleshooting 12
Frequently Asked Questions 13
Cleaning and Maintenance Instructions 14
Wiring Diagram 14

4
USER INSTRUCTIONS
POWER DATA
PRODUCT GUIDE
LPS-4414 LPS-5614 LPS-6814 LPS-8014 LPS-9614
Voltz/HZ
Amps
AC 120V 60Hz
14 Amps
AC 120V 60Hz
14 Amps
AC 120V 60Hz
14 Amps
AC 120V 60Hz
14 Amps
AC 120V 60Hz
14 Amps
Heater AC 120V 1500W AC 120V 1500W AC 120V 1500W AC 120V 1500W AC 120V 1500W
Lamps LED DC 12V LED DC 12V LED DC 12V LED DC 12V LED DC 12V
Rotor Motor
AC120V/60Hz
40mA 3.7W
18/15RPM CCW
AC120V/60Hz
40mA 3.7W
18/15RPM CCW
AC120V/60Hz
40mA 3.7W
18/15RPM CCW
AC120V/60Hz
40mA 3.7W
18/15RPM CCW
AC120V/60Hz
40mA 3.7W
18/15RPM CCW
Shipping
Size 46 1/4” x 26” x 8” 58 1/4” x 26” x 8” 70 1/4” x 26” x 8” 82 1/4” x 26” x 8” 98 1/4” x 26” x 8”
Model Viewing Area Firebox Dimensions Framing Dimensions
LPS-4414 43 3/4” W x 14” H 44 1/4” W x 23 3/4” H x 5 1/2” D 44 1/2” W x 24 1/8” H x 6” D
LPS-5614 55 3/4” W x 14” H 56 1/4” W x 23 3/4” H x 5 1/2” D 56 1/2” W x 24 1/8” H x 6” D
LPS-6814 67 3/4” W x 14” H 68 1/4” W x 23 3/4” H x 5 1/2” D 68 1/2” W x 24 1/8” H x 6” D
LPS-8014 79 3/4” W x 14” H 80 1/4” W x 23 3/4” H x 5 1/2” D 80 1/2” W x 24 1/8” H x 6” D
LPS-9614 95 3/4” W x 14” H 96 1/4” W x 23 3/4” H x 5 1/2” D 96 1/2” W x 24 1/8” H x 6” D
23 3/4”
(all models)
Width varies (see chart below) 5 1/2”
(all models)
Drywall stops Drywall stops

5
INSTALLATION
BOX CONTENTS
1 Fire Unit 1 Remote
4 L-Metal Mounting
Brackets
1 Trim Kit
1 Glass Face
Logs
Acrylic Media1 Owner’s Manual

6
INSTALLATION
INSTALLATION
WARNING: If the information in these
instructions is not followed exactly, a re
or explosion may result causing property
damage, personal injury or death.
WARNING - RISK OF FIRE!
To prevent a possible re, do not block air
intake or exhaust in any manner. Do not
use on soft surfaces where openings may
become blocked.
WARNING - RISK OF FIRE!
Do not blow or place insulation against the
rebox.
To reduce the risk of re do not store or
use gasoline or other ammable vapors in
the vicinity of this or any other heater.
CAUTION: Keep combustible materials,
such as furniture, pillows, bedding,
papers, clothes and curtains at least 3
feet (0.9m) from the front of the heater and
keep them away from the sides and rear.
CAUTION: Wear gloves and safety glasses
for protection during installation and
maintenance.
This replace can be installed fully recessed or half recessed.
To prepare for installation, connect the hard wire to the terminal block according to the diagram below.
Choose any connector type according to local building code.
To be performed by a qualied electrician
according to local building codes.
L - Line
- Ground
N - Neutral
Installing replace
Select a suitable location that is not susceptible
to moisture and is a safe distance from drapes,
furniture and high tra󰀩c areas. A qualied
electrician should add a dedicated exible 15
amp 120 volt circuit per local building codes.
Note: Follow all national and local electrical
codes.

7
INSTALLATION
Model WHD
LPS-4414 44 1/2” 24 1/8” 6”
LPS-5614 56 1/2” 24 1/8” 6”
LPS-6814 68 1/2” 24 1/8” 6”
LPS-8014 80 1/2” 24 1/8” 6”
LPS-9614 96 1/2” 24 1/8” 6”
1. This installation is optimized for a 2x6
framed wall. Prepare the framed opening
according to the chart above. Provide a
dedicated exible 15 amp 120 volt circuit for
hard wire installation.
2. Install L Metal Nailing Flanges to the
replace.
3. Install the re unit in the framed opening
with a minimum 1 ¼ drywall screws to
secure the unit.
4. Mask the exposed re unit during the
drywall process. Install drywall to the
drywall stops on the perimeter of the re
box. For more information on the drywall
stops see the Product Guide on page 4.
Decorate as desired.
Fully recessed installation

8
INSTALLATION
Installing Optional Wall Mounted Touch Control
1. Locate 2-gang low voltage bracket within 20 feet of replace. Install according to manufacturer’s
instructions.
2. Remove glass face (attached with magnets) from metal bracket.
3. Attach the metal bracket to the low voltage bracket with the included screws.
4. Insert batteries (2 AAA) and replace the glass face.
1. This installation is optimized for a 2x4
framed wall. Prepare the framed opening
according to the chart on page 7. Provide a
dedicated exible 15 amp 120 volt circuit for
hard wire installation.
2. Install L Metal Nailing Flanges to the
replace.
3. Install the re unit in the framed opening
with a minimum 1 ¼ drywall screws to
secure the unit.
4. Mask the exposed re unit during the
drywall process. Install drywall to the
perimeter of the re box. The unit can be
covered with a custom facade or optional
Slim Cabinet (shown in diagram). Decorate
as desired.
Half recessed installation

9
OPERATION
OPERATION
This will cycle the machine on and o󰀨. Upon cycling
power on, the machine will return to the settings it had
when it was cycled o󰀨.
If the replace is on, this button will act as a reset and
bring all colors back to the default Modern Flames'
signature color.
This will cycle the heater between high, low and o󰀨.
All zones of the replace will slowly fade between
various colors.
Pressing the sync button will change all the colors of
the replace) Flame, Ember Bed and Downlight) to
match the current color of the ame setting.
This is a zone setting. Touching this button will allow
you to change the color and brightness of the ame by
using the RGB wheel and brightness slider.
This is a zone setting that controls the color and
brightness of the ember bed.
This is a zone setting that controls the color and
brightness of the downlight.
The unit has a main power switch just in front of the glass on the top right hand side. A hand-held remote
is included.
Power indicator lights for wall switch as well
as upper right corner of the main unit
When the switch turns on, this orange pilot lamp
turns on. It shows the re is energized.
The status light above shows that the power is on
and the heater is on low. (2500 BTU)
The status light above shows that the power is on
and the heater is on high. (5000 BTU)
Pairing remote/wall mounted touch control:
1. With the replace ON press and hold the Power button for about 3 seconds until you hear the buzzer
sound twice and the power indicators begin to ash.
2. Within 5 seconds on the hand held remote or wall touch control press the Power button repeatedly
until the buzzer sounds again and the indicators ash acknowledging that it has paired. You may also
hear another buzzer and the pair is now completed.
• Pairing must be done within 5 seconds or the replace will time out of pairing mode.
• To clear any paired remotes from the unit, locate then press and hold the reset button for 3 seconds.
You should hear a buzzer letting you know the codes have been cleared so you can now pair a new
remote or wall touch control. (The reset is located next to the manual controls and can be pressed
with a paper clip.)
Power
Reset
Heat
Fade
Sync
Flame
Ember
Bed
Downlight
Manual Controls
The unit has manual controls located next to the
power switch, just in front of the glass on the top
right side.
Power
Turns unit
on/o󰀨
Heat
Cycles
heat low/
high/o󰀨
Color
Changes
all
replace
colors
together
Reset
Resets
unit

10
MAINTENANCE
SERVICE PARTS
ITEM PHOTO DESCRIPTION
MF-PRO-PCB
PRINTED CIRCUIT BOARD CONTROLS LOW
VOLTAGE AND HIGH VOLTAGE FUNCTIONS
AND TRANSFORMER
MF-PRO-WIFI
WIFI
WIFI BOARD
MF-PRO-HF HEATER FAN 120 V
MF-PRO-PTC PTC HEATER 120/240 V 1500/3000 WATTS
MFSM120 SPINDLE MOTOR 120 V 50-60 HZ
MF-PRO-RC PRO SERIES RF REMOTE CONTROL
MF-PRO-WTC
OPTIONAL
WALL MOUNTED TOUCH CONTROL
ASSEMBLY
MF-PRO-TB TERMINAL BLOCK 120/240 V
MF-PRO-MTC MANUAL TOUCH CONTROL BOARD
MFPS2 20 AMP POWER SWITCH

11
MAINTENANCE
SERVICE PARTS
ITEM PHOTO DESCRIPTION
MF-PRO-PIB POWER INDICATOR BOARD
MF-PRO-NTC THERMOSTAT SENSOR
MF-LPS-TK-44
TRIM KIT
MF-LPS-TK-56
MF-LPS-TK-68
MF-LPS-TK-80
MF-LPS-TK-96
MF-LPS-F/LED-44
RGB FLAME LED BAR
MF-LPS-F/LED-56
MF-LPS-F/LED-68
MF-LPS-F/LED-80
MF-LPS-F/LED-96
MF-LPS-EB/DL-44
RGB EMBER BED/DOWNLIGHT LED STRIP
MF-LPS-EB/DL-56
MF-LPS-EB/DL-68
MF-LPS-EB/DL-80
MF-LPS-EB/DL-96
MF-LPS-SR-44
SPINDLE ROD FOR FLAME OR EMBER BED
MF-LPS-SR-56
MF-LPS-SR-68
MF-LPS-SR-80
MF-LPS-SR-96
MF-LPS-GF-44
FRONT GLASS
MF-LPS-GF-56
MF-LPS-GF-68
MF-LPS-GF-80
MF-LPS-GF-96
MF-LPS-PP-44
POLY SCREEN
MF-LPS-PP-56
MF-LPS-PP-68
MF-LPS-PP-80
MF-LPS-PP-96

12
MAINTENANCE
TROUBLESHOOTING
Problem Possible Cause Corrective Action
Nothing comes on (touch screen,
etc.)
A. Breaker tripped or circuit has
no power
A. Reset breaker, test circuit for
power
B. Internal component is frozen
and needs to be reset
B. Turn power o󰀨 at the main
breaker for 20 seconds. Turn
power back on.
C. Loose connection C. Look for loose connection
D. Defective component D. Replace motherboard or touch
control
Touch Screen Comes on - then
nothing
A. Not operating touch control
properly with nger
A. Press at part of nger rmly
on the touch screen and apply
moderate pressure
B. Loose connection on
motherboard
B. Check functions with remote
control. If functional, check
connections on motherboard
C. Motherboard is defective C. Replace Motherboard
Fireplace turns o󰀨 and will not
turn back on
A. Fireplace has overheated and
safety disc has snapped or circuit
breaker has tripped
A. Turn the main breaker to the
“o󰀨” position for 30 seconds.
Next ip the breaker back into
the “on” position.
Can operate replace functions
with manual controls but not
remote control
A. Low Batteries A. Replace batteries in remote
control with - CR2025
B. Remote not paired properly
B. With the replace ON press
and hold the Power button for
about 3 seconds until you hear
the buzzer sound twice and the
power indicators begin to ash.
Within 5 seconds on the hand
held remote or wall touch
control press the Power button
repeatedly until the buzzer
sounds again and the indicators
ash acknowledging that it
has paired. You may also hear
another buzzer and the pair is
now completed.
C. Remote control defective C. Replace remote control
Heater does not provide heat
when on
A. Wiring is loose
A. Disconnect unit from power
source and inspect for loose
connections
B. Snap disc tripped B. Turn o󰀨 for 5 minutes to reset
C. Heater core is defective C. Replace Heater Core

13
MAINTENANCE
FREQUENTLY ASKED QUESTIONS
Q. How do you change the optional Wall Touch Control to Fahrenheit/Celsius?
A. Long press on the up and down arrows on the re unit to toggle between Fahrenheit and Celsius.
Q. What distance can the remote be used from the replace?
A. Optimal distance for the remote control is within 20 feet.
Q. Can you turn on the replace via the manual control and o󰀨 via the remote (or vise versa)?
A. Yes.
Q. Can the replace be installed outside?
A. No. Please review the entire safety chapter before installing this replace.
Q. Does the replace need to be on a dedicated 15 amp circuit?
A. Yes.
Q. What thickness of sheetrock should be used for the recessed installation?
A. 1/2” or 5/8”, thinner is recommended for tile façade.
Q. How often do the batteries in the remote need to be replaced?
A. Annually, possibly more with heavy use.
Q. Is there a remote receiver in the replace that requires batteries?
A. No, only the actual remote requires batteries. The rest of the replace runs entirely o󰀨 of the main
power supply.
Problem Possible Cause Corrective Action
Flame is not visible when unit is
turned on
A. Wiring is loose
A. Disconnect unit from power
source and inspect for loose
connections
B. LEDs defective B. Replace LEDs
C. Motherboard is defective C. Replace motherboard
Fireplace lights up but there is
no ame image or ame image
frozen
A. Wiring for motor is loose
A. Disconnect unit from power
source and inspect for loose
connections from motor
B. Spindle rod came loose B. Reconnect spindle rod
C. Motor is defective C. Replace motor
Fireplace is squeaking when
ame image is on
A. Fireplace spindle/rod is
contacting to metal
A. Apply lithium grease or any
standard grease to contacts with
rod and metal
B. Motor is defective B. Replace motor

14
MAINTENANCE
CLEANING AND MAINTENANCE INSTRUCTIONS
WIRING DIAGRAM
There is very little maintenance involved with your electric replace. Please follow the few points below:
• On a semi-annual basis unplug the machine from it’s power source, wait for the heating element to
cool and dust the re unit with a dry cloth. Be careful not to brush any wires that may be exposed as
you do this.
• To clean the glass face of the replace simply use your desired glass cleaner with paper towels.
• To clean the air inlets/outlets, wipe with a soft cloth or the nozzle of a vacuum cleaner
• Dust can easily build up around the heater area inside the re unit, on the left and right sides. Take
particular care to clean this area on a regular basis to prevent buildup.
• For long periods of inactivity, please unplug the replace and ensure the surrounding area remains
dry.
Downlight
Ember Bed light
Flame light
WIFI

15
MAINTENANCE
NOTES

16
©2019
www.modernames.com
Please dispose of properly.
V1