modway EEI-2236 User manual

EEI –2236 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 1 of 5
Thank you for purchasing the MODWAY OFFICE CHAIR.
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2. Owing to the size and weight of the chair, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 30 minutes.
3. Please do not use any tools other than those provided or recommended in these instructions.
4. Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6. Please keep all fitting out of reach of children.
Hardware:
A. Bolt M8x50mm x 4
B. Crash Pad x 4
C. Cap Cover x4
D. Allen Wrench x1
Component:
1 Base x1 2 Cylinder Column x1 3 Foot Ring x1 4 Castor x5
5 Back with Control Mechanism x1 6 Arm x2
1
2
3
4
4
4
5
6
6

EEI –2236 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 2 of 5
STEP 1:
Please put Base (1) on a carpeted or padded surface.
Insert 1 piece of Castor (4) into the Base (1) as shown by hand.
Repeat the same steps for the remaining 4 pieces of Castors (4).
STEP 2:
Carefully turn over the assembled Base (1) from step 1.
Insert the Cylinder Column (2) as shown.
4
1
4
4
4
4
2
1
1
2

EEI –2236 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 3 of 5
STEP 3:
Insert the Foot Ring (3) into the assembled Cylinder Column (2) at your desired height. But at least one inch
from the top of the outer circle of Cylinder Column (2) as shown. Please follow the shown direction of the arrow
to tighten the knob by hand on the Foot Ring (3) until the Foot Ring (3) is fixed.
STEP 4:
Attach Arm (6) to the Back with Control Mechanism (5) by using 2 pieces of Bolts (A) with 2 pieces of Crash
Pads (B) as shown.
Tighten Bolts (A) by using Allen Wrench (D) as shown.
Hardware & Tools required
2
1 inch
3
2
3
A
D
5
6
B
B
A
x 2
B
x 2
D
x 1

EEI –2236 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 4 of 5
STEP 5:
Repeat the same steps for another Arm (6). Tighten Bolts (A) by using Allen Wrench (D) as shown.
Hardware & Tools required
STEP 6:
Insert Back with Control Mechanism (5) into the Cylinder Column (2) as shown.
A
x 2
B
x 2
D
x 1
5
6
B
B
A
D
6
2
5
5
2
5

EEI –2236 Office Chair
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 5 of 5
STEP 7:
Assembly is complete. Your office chair is ready to be used now!
Attention: When you use the handle to
adjust the height to be lower, please move
away your legs from the foot ring at the
same time.