modway EEI -2785 User manual

Customer Service 908-368-1025︱www.modwayfurniture.com Page 1 of 6
EEI –2785 DESK
Thank you for purchasing the MODWAY DESK！
Before you start, here is some helpful advice:
1.We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the desk, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 45 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components and
hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe and
environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the
components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Hardware:
A Cam x16
B
D
Components:
1 Desk Top x1 2 Left Frame x1
Cam Post x16
1
6
7
3
8
3
4
5
2
C Long Screw M4x35mm x8
E Dowel x14
F Drawer Glides x1
Short Screw M4x14mm x8
Phillips Head Screwdriver
( Not included)
9
10
11
12
3 Right Frame x1 4 Back Panel x1
5 Frame Left x1 6 Frame Right x1 7 Frame Back x1 8 Drawer Front x1
Drawer Left x1 Drawer Right x1 11 Drawer Back x1 12 Drawer Bottom x1
9 10

Customer Service 908-368-1025︱www.modwayfurniture.com Page 2 of 6
EEI –2785 DESK
HOW TO USE CAM AND CAM POST HARDWARE
STEP 1:
1. 2.
3. 4.
Note cam arrow
direction
Note cam arrow
direction
Turn cam clockwise
1/2 turn
5.
Put Drawer Front (8), Drawer Left (9), Drawer Right (10), Drawer Back (11), Drawer Bottom (12) together as shown.
Attach them by using 2 pieces of Cam Post (B), 2 pieces of Cam (A), and 4 pieces of Long Screw (C).
Fully tighten Cams (A) and Screws (C) by using Phillips Head Screwdriver (not included).
Ax2 Bx2 Cx4 Phillips Head Screwdriver
( not included) Hardware & Tools required
12
8
10
9
11
A
B
A
B
C
C
C
C
and

Customer Service 908-368-1025︱www.modwayfurniture.com Page 3 of 6
EEI –2785 DESK
STEP 2:
STEP 3:
Put Frame Left (5), Frame Right (6), and Frame Back (7) together as shown.
Attach them by using 4 pieces of Long Screw (C).
Use Phillips Head Screwdriver (not included) to tighten Long Screws (C) until secure.
Insert 2 pieces of Dowel (E) into each piece of Frame Left (5) and Frame Right (6) as shown.
Hardware & Tools required
Hardware & Tools required
Cx4 Ex4 Phillips Head Screwdriver
( not included)
Place 1 set of Drawer Glides (F) to the assembled Drawer Frame as shown.
Attach them by using 4 pieces of Short Screw (D).
Use Phillips Head Screwdriver (not included) to tighten Short Screws (D) until secure.
6
5 7
C
C
C
C
E
E
E E
7
6
5
F
F
D
D
D
D
Dx4 Phillips Head Screwdriver
( not included)

Customer Service 908-368-1025︱www.modwayfurniture.com Page 4 of 6
EEI –2785 DESK
STEP 4:
STEP 5:
Hardware & Tools required
Hardware & Tools required
Bx14 Phillips Head Screwdriver
( not included)
Place the assembled Drawer Frame to Desk Top (1) as shown.
Attach them by using 6 pieces of Cam (A).
Use Phillips Head Screwdriver (not included) to tighten Cams (A) until secure.
Put Desk Top (1), Left Frame (2), and Right Frame (3) upside down on a carpeted or padded surface.
Insert 6 pieces of Cam Post (B) into the pre-drilled holes on Desk Top (1).
Insert 4 pieces of Cam Post (B) into the pre-drilled holes on each Left Frame (2) and Right Frame (3).
Use Phillips Head Screwdriver (not included) to tighten Cam Post (B) until secure.
1
2
A
A
1
3
B
B
B
B B B
B B
B
B
B
B
B
B
A
A
A
A
5
6
7
F
F
Ax6 Phillips Head Screwdriver
( not included)

Customer Service 908-368-1025︱www.modwayfurniture.com Page 5 of 6
EEI –2785 DESK
STEP 6:
STEP 7:
Hardware & Tools required
Hardware & Tools required
Ax8 Phillips Head Screwdriver
( not included)
Fully pull out Drawer Glides (F) as shown.
Place the assembled drawer to Drawer Glides (F).
Attach the drawer by using 4 pieces of Short Screw (D).
Use Phillips Head Screwdriver (not included) to tighten Short Screws (D) until secure.
Dx4 Phillips Head Screwdriver
( not included)
Put Left Frame (2) and Right Frame (3) to the assembled Top panel (1), Back Panel (4), and Drawer Frame (5 6 7)
Attach them using 8 pieces of Cam (A)
Use Phillips Head Screwdriver (not included) to tighten Cams (A) until secure.
3
4
3
4
1
2
D
D
D
D
2
1 5
6 7
A
A
A
A A A
A
A
F
&&
as shown.

Customer Service 908-368-1025︱www.modwayfurniture.com Page 6 of 6
EEI –2785 DESK
STEP 8:
Place the assembled desk to the position you desired.
Assembly is complete. Your desk is ready to be used now!