modway EEI-3044 User manual

EEI-3044 Sofa
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 1 of 5
Thank you for purchasing the
MODWAY SOFA.
Before you start, here are some helpful advice:
1. We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step
instructions.
2.Owing to the size and weight of the sofa, we recommend that it is assembled by two adults, on a carpeted or
padded area, in the room that it is intended for. Approximate assembly time: 25 minutes.
3.Please do not use any tools other than those provided or recommended in these instructions.
4.Please do not throw away any of the packaging or the instruction until you have checked all the components
and hardware and the furniture is fully assembled. Please ensure that the packaging is disposed of in a safe
and environmentally friendly way.
5.Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten
the components from time to time, so please save the tools that have been provided.
6.Please keep all fitting out of reach of children.
Hardware:
A. Bolt M8x60mm x 11
B. Flat Washer M8x 11
C. Allen Wrench x1
Component:
1 Back Cushion x2 2 Seat Cushion x2 3 Pillow x2 4 Left Arm x1
5 Right Arm x1 6 Seat Frame x1 7 Back Frame x1 8 Leg x4
3
5
6
7

EEI-3044 Sofa
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 2 of 5
STEP 1:
Please take the Left Arm (4), Right Arm (5), Leg (8) and hardwares bag from the bottom of Seat Frame (6).
Then carefully remove plastic packaging of the compressed Seat Cushions (2) and Back Cushions (1). Being
carefully not to cut through to them.
Place compressed Seat Cushions (7) and Back Cushions (1) on a flat surface in a well ventilated room and
allow 48 hours for expansion.
Due to the unique properties of the compressed Seat Cushions (7) and Back Cushions (1),dimensions after
expansion will vary slightly; this isnormal and will not affect the performance of your sofa.
STEP 2:
Please put Sofa Frame (6) on a carpeted or padded surface.
Insert Leg (8) to the bottom of Frame (6) and tight by hand in the direction of the arrow as shown.
Repeat the same steps for the other 3 pieces of Leg (8).
8
8
8
6
FRONT
BACK
8
2
6
4
5

EEI-3044 Sofa
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 3 of 5
STEP 3:
Attach Left Arm (4) to the side of Seat Frame (6) by using 4 pieces of Bolts (A) with 4 pieces of Flat Washers (B)
as shown.
Tighten Bolts (A) by using Allen Wrench (C) as shown. Don't tight %ROWV$ fully.
Hardware & Tools required
STEP 4:
Attach Right Arm (5) to the side of Seat Frame (6) by using 4 pieces of Bolts (A) with 4 pieces of Flat Washers
(B) as shown.
Tighten Bolts (A) by using Allen Wrench (C) as shown.Don't tight %ROWV$ fully.
Hardware & Tools required
A
x 4x 4
B
x 1
C
A
x 4x 4
B
x 1
C
A
C
B
6
4
FRONT
BACK
6
A
C
B

EEI-3044 Sofa
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 4 of 5
STEP 5:
Slide the two clips of Back Frame (7) to the clips of the side of the Left Arm (4), Right Arm (5) by hand in
the direction of the arrow as shown.
STEP 6:
Insert 3 pieces of Bolts (A) with 3 pieces of Flat Washers (B) into the pre-drilled holes on Seat Frame (6) .
Use Allen Wrench (C)to tighten Bolts (A) as shown. Don't tight %ROWV$ fully.
When /HIW$UP, 5LJKW$UP and %DFN)UDPH fixed, please fully tighten all %ROWV$.
Hardware & Tools required
A
x 3x 3
B
x 1
C
4
5
6
7
4
6
4
5
FRONT
BACK

EEI-3044 Sofa
Customer Service 908-368-1025︱www.modwayfurniture.com
Page 5 of 5
STEP7:
Carefully turn over the assembled unit from step 6 as shown.
Put Back Cushion (1), Seat Cushion (2), and Pillow (3) to the assembled sofa as shown.
Assembly is complete. Your Sofa is ready to be used now!
6
2
2
1
1