Monte Carlo Fan Company 5TV52XXD Series User manual

R
5TV52XXD Series Fan
onteCarloFans.com
UL odel No. 5TV52
Total fan weight
with light kit READ AND SAVE
THESE INSTRUCTIONS
To register your fixture, please visit our website:
MonteCarloFans.com
Si necesita asistencia en la instalación,
piezas de repuesto, o tiene preguntas
acerca de nuestra garantía, por favor
llame a nuestro centro de servicio
al cliente:
Si vous avez besoin d'aide pour l'installation,
des pièces de remplacement, ou si vous avez
des questions concernant notre garantie,
veuillez contacter notre service après-vente:
If you need installation
assistance, replacement parts,
or have questions regarding
our warranty, please call our
customer care center:
NEED HELP?
¿NECESITA AYUDA?
AVEZ-VOUS BESOIN D’AIDE?
Please do not return this product to the store.
Por favor no devulva este producto a la tienda.
Prière de ne pas retourner ce produit au magasin.
1-800-519-4092
MonteCarloFans.com
STOP ALTO

Installation work and electrical wiring must be done by qualified person(s) in accordance with applicable codes and standards (ANSI/NFPA 70-1999),
including fire-rated construction.
Use this unit only in the manner intended by the manufacturer. If you have any questions contact the manufacturer.
After making the wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side
of the outlet box and ungrounded conductor on the other side of the outlet box. The splices, after being made, should be turned upward and
pushed carefully up into the outlet box.
#: Before you begin installing the fan, servicing or cleaning unit, Switch power off at Service panel and lock service disconnecting means to
prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning
device, such as a tag, to the service panel.
Be cautious! read all instructions and safety information before installing your new fan. Review the accompanying assembly diagrams.
When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities.
ake sure the installation site you choose allows the fan blades to rotate without any obstructions. Allow a minimum clearance of 7 feet from the floor to
the trailing edge of the blade.
#: To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked “acceptable for fan support” and use mounting
screws provided with the outlet box ( ounting must support at least 35 lbs.)
#: To reduce the risk of personal injury, do not bend blade holders during installation to motor, balancing or during cleaning. Do not insert for-
eign object between rotating blades.
Attach the mounting bracket using only the hardware supplied with the outlet box.
#: To reduce the risk of fire or electric shock, this fan must be installed with an isolating wall control/switch.
#: To reduce the risk of fire or electric shock, do not use this fan with any solid state fan speed control device, or variable speed control.
If this unit is to be installed over a tub or shower, it must be marked as appropriate for the application.
NEVER place a switch where it can be reached from a tub or shower.
The combustion airflow needed for safe operation of fuel-burning equipment may be affected by this unit’s operation. Follow the heating equipment man-
ufacturer’s guideline safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating,
Refrigeration and Air Conditioning Engineers (ASHRAE) and the local code authorities.
"!To Reduce the Risk of Electric Shock, Disconnect the electrical supply circuit to the fan before installing the light kit.
All set screws must be checked and tightened where necessary before installation.
1.
2.
3.
4.
5.
6.
7.
8.
9.
10.
11.
12.
13.
14.
15.
16.
17.
Installation
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS,
OBSERVE THE FOLLOWING: READ AND SAVE THESE INSTRUCTIONS
!$ !
! "
Phillips Screwdriver Wire Cutters Pliers Step Ladder
Before you begin installing the fan, Switch power off
at Service panel and lock service disconnecting means
to prevent power from being switched on accidentally.
When the service disconnecting means cannot be
locked, securely fasten a prominent warning device,
such as a tag, to the service panel.

Before installing this fan make sure the outlet
box is properly installed to the house structure.
To reduce the risk of fire, electric shock, or per-
sonal injury, mount to outlet box or supporting
system acceptable for fan support.
( ounting must support at least 35 lbs.)

Thread safety cable through center
hole of the mounting plate. Thread
your house wires through center hole
also.These will be needed for wiring
of the fan.

Securely attached the mounting
plate to the outlet box using two
screws supplied by the outlet box.
"5)0)6%/276/)6&2:57-6%&/)*24
*%1573324607565733246
/&5

Place the decorative ring on the
motor housing.

For Canadian installation and for USA fan and
light kit combinations over 35 lbs, in both flush
and downrod mode the safety cable must be
installed into the house structure beams using
the 3” lag screws provided. ake sure that
when the safety cable is fully extended the
leadwires are longer than the cable and no
stress is placed on the leadwires.
Safety cable installation
%*)6;%&/)
%+ '4)9
%+ '4)9
%*)6;%&/)
#%5,)4
2'.#%5,)4

Lift the motor housing up aligning the L
shape holes with the screws and
washers on the mounting plate. Turn the
housing clockwise to hold in position.
Install the other two screws and washers
previously removed securely.

Loosen the two screws and washers
across from each other on the ridge
of the mounting plate. Remove the
other two screws and lock washers.
Save for later use.

ake wire connections to power source using
wire nuts provided. ake sure that no filiments
are outside of the wirenut. After making the
wire connections, the wires should be spread
apart with the grounded conductor and the
equipment-grounding conductor on one side of
the outlet box and ungrounded conductor on
the other side of the outlet box.

Lift the decorative ring up and twist clock-
wise till tight.

Check the motor for shipping stabi-
lizers and remove if present. Attach
blades using screws and washers in
hardware pak. Tighten screws
securely.

Loosen 2 screws and remove 1 screw
from motor plate. Save removed
screw for use later.

Connect plug from fan to switch
house plug.

Install by twisting clockwise, add 1
screw removed step 14 to switch
housing plate. Tighten the 3 screws
securely.

Connect white wire from fan to white
wire from light fixture. Then plug
blue wire from fan to black wire from
light fixture.

Loosen the pre installed screws of
switch housing plate.

Connect black and blue wire from fan to Black
or (Hot) wire from house. Connect White wire
from Fan to White (Neutral) wire from house.
Connect Ground leads from mounting bracket
and downrod to Ground lead from house.
)*)462 %*)6;!-355)'6-212*0%17%/

Carefully lift the fan motor assembly
and engage the slot in the motor
housing with the hook on the mount-
ing plate so that the motor is secure-
ly suspended.


Install 3 screws to install light pan.

24*%19-6,/-+,6.-6+2
6256)362
*-1-5,
24*%19-6,276/-+,6.-6
+26256)3
Attach glass by locating dimples in
light fixture with the groves in glass
and twisting clockwise till tight.

Attach the non light cover by locating
dimples in the light fixture with the
grooves in the non light kit cover and
twist clockwise till tight. #
ake sure light bulb is not installed
when using this cover.

Install 75 watt halogen bulb. Do not touch
bulb surface as oily residue from skin can
cause the bulb to explode. Bulb Included.
# 8)4/%03-1+ 6,)
*%19-//4)57/6-16,) *%1/-+,65
5,766-1+(291 716-/ 6,)3423)4
9%66%+) 2* &7/&5 %4)-156%//)(
)5)66,)/-+,65&;6741-1+2**6,)
9%//59-6',&4)%.)424&;4)026)
)3/%')&7/&59-6,6,)'244)'6
9%66%+)&7/&567416,)329)421


2. If fan sounds noisy:
1. If fan does not start:
3. If fan wobbles:
4. If light does not work:
Trouble Shooting
If you have difficulty operating your new ceiling fan, it may be the result of incorrect assembly, installation,
or wiring. In some cases, these installation errors may be mistaken for defects. If you experience any faults,
please check this Trouble Shooting Chart. If a problem cannot be remedied, or you are experiencing difficulty
in installation, please call our Customer Service Center at the number printed on your parts list insert sheet.
#%41-1+)*24)5)48-'-1+24'/)%1-1+71-6 9-6',329)42**%6 )48-')3%1)/%1(/2'.5)48-')(-5
'211)'6-1+0)%156234)8)16329)4*420&)-1+59-6',)(21%''-()16%//;#,)16,)5)48-')(-5
'211)'6-1+0)%15'%1126&)/2'.)(5)'74)/;*%56)1%3420-1)169%41-1+()8-')57',%5%6%+
626,)5)48-')3%1)/
!427&/) 7++)56)()0)(;
1.Check main and branch circuit fuses or circuit breakers.
2.Check line wire connections to fan and switch wire connections in switch housing.
3.Check to make sure the dip switches from the transmitter and receiver are set on the same
frequency.
"!%.)574)0%-1329)4-56741)(2**
1.Check to make sure all screws in motor housing are snug (not over tightened).
2.Check to make sure the screws which attach the fan blade holder to the motor are tight.
3.Check to make sure wire nut connectors in switch housing are not rattling against each
other or against the interior wall of the switch housing.
"!%.)574)0%-1329)4-56741)(2**&)*24))16)4-1+59-6',,275-1+
4.Some fan motors are sensitive to signals from Solid State variable speed controls.
!" % 2/-( 6%6)8%4-%&/)53))('21642/
5.Allow "break-in" period of 24 hours. ost noises associated with a new fan will disappear
after this period.
1. ake sure that the ridge of the canopy engages the notch in the downrod ball.
2.Check that all blades are screwed firmly into blade holders.
3.Check that all blade holders are tightened securely to motor.
4. ake sure that canopy and mounting bracket are tightened securely to ceiling junction box
and junction box is mounted firmly to ceiling joist.
5. ost fan wobble problems are caused when blade levels are unequal. Check this level by
selecting a point on the ceiling above the tip of one of the blades. easure this distance from
blade tip to ceilng. Keeping measure within 1/8", rotate the fan until the next blade is posi-
tioned for measurement. Repeat for each blade. If all blade levels are not equal, you can
adjust blade levels by the following procedure. To adjust a blade tip down, insert a washer
(not supplied) between the blade and blade holder at the screw closest to the motor. To
adjust a blade tip up, insert washer (not supplied) between the blade and blade holder at the
two screws farthest from the motor. Reverse the position of the washer if blades mount from
top of blade.
6.If blade wobble is still noticeable, interchanging two adjacent (side by side) blades can
redistribute the weight and possibly result in smoother operation.
1.Check wire from fan to make sure it is connected to hot wire from house.
2.Check for loose or disconnected wires in fan switch housing.
3.Check for loose or disconnected wires in light kit.
4.Check for faulty light bulbs.
"!%.)574)0%-1329)4-56741)(2**&)*24))16)4-1+59-6',,275-1+
Customer Service Center:
301 West Washington St.
Riverside, NJ 08075
1-800-519-4092
www.montecarlofans.com

Apr.7.10 issued