Montigo H38-DF Instruction Manual

Brackets to be
flush with top of
fireplace frame,
(Typical)
Align (2) attachment brackets
on center of frame verticals
(Left and Right side Typical)
Moving Brackets (2)
(Left and Right side Typical)
Mounting Holes (3) per side.
(Left and Right side Typical)
Bracket to be
Flush with
outside edge
of fireplace,
(Typical)
Installing the H38 & H42 Surround
for use with:
H-Series; H38-DF
H-Series; H42-DF
Parts Included
1) 1-Pc,Surround
2) 2-Pcs,AttachmentBrackets
3) 2-Pcs,MovingBrackets
4) 1-Pkg.Hardware
Dimensions
Figure1. Surround Dimensions
®
C US
13
2
4
Tools Required
1) PowerDrill,(six1/8"holes)
2) #8HexheadDriver,(tomatchhardware)
3) Carpenterslevel(FinalStep,ifrequired)
Installing the Surround
 ToinstalltheMontigoStainlesssteelorBlackcontemporarysur-
roundtootheH38DF&H42DFfollowthesefewsimplesteps.
Step 1. Mark the location of the holes needed.
 FromthepackageofhardwarelocateoneoftheAttachment
Brackets.HoldthispartinplaceasshowninFigure 2.Withapen-
cilorpenmarkthe(6)sixholesonthefaceofthereplaceframe,
(seeFigure2.)Note:Ensure the brackets align with Figure 2. Below.
Figure2.Bracket Alignment
Step 2. Drill holes.
Before you go any farther now is the time to double check the loca-
tion of the holes, do they agree with Figure 2. Ifyouaresatised
withthelocationoftheholes,useapunchtomarktheholes,then
usinga1/8"drill,drilloutthesixholes.
M
N
P
1”
O
M (Hor. open’g) O
H38DF 35 25 49
1
/ 2
N (Vert. open’g)
Surround Dimensions
P
H42DF
1
/ 8
39
39 28
7
/ 16
53
1
/ 2
43
3
/ 32
5
/ 8

XG0903-013111
f i r e f e a t u r e
Movable Bracket
Fixed Bracket
Supplied, 1/2”Long
10/24 machine screw.
Fixed 10/24 Nutsert
Step 3. Install the (2) two Attachment Brackets.(See Figure 2)
 Nowit'stimetoinstallthetwo(2)AttachmentBracketsyouused
asaguide.HavesomeoneholdoneoftheBracketsinplace,
usingtheHex-tool,placeaself-tapping#8-18sheetmetalhex
screwintotheholeandtwistitintotheholehalfway.
Followthisprocedurefortheremainingtwo(2)screwsintherst
bracket.Afterthethree(3)screwsareinplacetightenthemin
place.RepeattheprocedureinStep 3forthesecondAttachment
Bracket.
Step 4. Install the (2) two Movable Brackets.(If installed disregard this
step. If not See Figure 3)
 Nowit'stimetoinstallthetwo(2)MovableBrackets.(These
move up or down to level and align the surround. This will pro-
duce a symmetrical reveal when correctly adjusted).
Figure3. Installing the Movable Brackets
Pickuponeofthebrackets,usingthesuppliedhardware,mountitinto
place.Slidetheboltthroughthebracket'fronttoback',(SeeFig-
ure3),thentightentheboltusingaopenendwrenchorsocket.
FollowthisprocedurefortheremainingboltinthesecondMovable
Bracket.
Step 5. Placing the Surround
 Finallyit'stimetoinstalltheStainlesssteelorBlackSurround.
Forthisstepitwouldbehelpfultohavesomeonehelpyouhold
thesurroundinplace.
Liftthesurroundoverthetwo(2)MovableBracketsandswingthesur-
rounddownward.Ifthesurrounddoesn'tclearthetoporbottom
ofthereplaceyouwillhavetoadjustthemovablebracketsupor
down.Removethesurroundplaceitaside.Adjustthebracketas
required.Repeatasnecessary.
Step 6. Final adjusting of the Surround
 Thisstepisnotnecessaryifthesurroundtstightlyaroundthe
replace,ortheadjustmentisacceptable.But,ifyoursurround
hasanunevenreveal,orunequalgaparound/betweenthere-
placeandsurround,usingacarpentersleveladjusttheMovable
bracketsasneeded.
FinallyplacetheadjustedSurroundbackontheBracketsandadmire
yourContemporaryMontigoreplace.