Montigo Proflame 2 RX 300 NG Instruction Manual

XT0016
Installation & Maintenance Manual
• Theinstallationofthisreplacemustbedonebya
qualiedandcertiedgasapplianceinstaller.
• Checklocalcodesandreadallinstructionspriorto
installation.
®
C
US
WARNING:
FIRE OR EXPLOSION HAZARD
Failure to follow safety warnings exactly could result in serious injury,
death, or property damage.
—Donotstoreorusegasolineorotherammablevaporsand
liquidsinthevicinityofthisoranyotherappliance.
— WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phoneinyourbuilding.
• Leavethebuildingimmediately.
• Immediatelycallyourgassupplierfromaneighbour's
phone. Follow the gas supplier’s instructions.
• Ifyoucannotreachyourgassupplier,callthere
department.
—Installationandservicemustbeperformedbyaqualied
installer,serviceagencyorthegastter.
PROFLAME 2 UPGRADE KIT
RX 200 + RX 300 NG/LP
Upgrade Kit NG/LP Proame 2
(Basic to Full Load with Remote)
THIS KIT IS FOR USE WITH THE FOLLOWING MODELS:
RX200:
B34DT-2-F : B34 TOP VENT, ELECTRONIC IGNITION, IPI
B34DR-2-F : B34 REAR VENT, ELECTRONIC IGNITION, IPI
B38DT-2-F : B38 TOP VENT, ELECTRONIC IGNITION, IPI
B38DR-2-F : B38 REAR VENT, ELECTRONIC IGNITION, IPI
PL38DFN-F : PL38 , ELECTRONIC IGNITION, IPI
PL38DFL-F : PL38 , ELECTRONIC IGNITION, IPI
PL42DFN-F : PL42 , ELECTRONIC IGNITION, IPI
PL42DFL-F : PL42 , ELECTRONIC IGNITION, IPI
PL52DFN-F : PL52 , ELECTRONIC IGNITION, IPI
PL52DFL-F : PL52 , ELECTRONIC IGNITION, IPI
RX300:
DL6315NI : DL6315, ELECTRONIC IGNITION, IPI
DL6315STNI : DL6315ST, ELECTRONIC IGNITION, IPI
Ensure that all power to the appliance is o at the electrical breaker
or fuse before beginning installation. Ensure gas is turned o at the
shuto valve before beginning installation.
When installing the replace - gas lines, ttings, accessories or any
other objects cannot impede the proper movement of the door
buckles.
CAUTION
WARNING
Some materials used in the manufacturing process of this product can
expose you to Benzene which is known in the State of California to
cause cancer and birth defects or other reproductive harm. For more
information go to www.P65warnings.ca.gov
WARNING

XT00162
General
This upgrade kit shall be installed by a qualied service agency in
accordance with the manufacturer's instructions and all applicable
codes and requirements of the authority having jurisdiction. If the
information in these instructions are not followed exactly, a re,
explosion or production of carbon monoxide may result causing
property damage, personal injury or loss of life. The qualied service
agency is responsible for the proper installation of this kit. The
installation is not proper and complete until the operation of the
converted appliance is checked as specied in the manufacturer's
instructions supplied with this kit.
This upgrade kit contains the necessary components for eld upgrade
of an approved Montigo replace from Proame 2 basic control
system to Full Load with remote.
The installation of this unit must also conform with local codes or, in
the absence of local codes, with the American National Fuel Gas Code,
ANSI Z223.1, or the Canadian Installation Code, CAN / CGA B149.
WARNING
GENERAL INFORMATION
Note
Upon successful installation of
this upgrade kit, the following
features are available for the
user:
1. Thermostatic and smart
thermostatic control of the
replace
2. Main burner flame
modulation (6 levels)
3. Choice of Standing or
Intermittent pilot (CPI switch
or jumper required)
4. Comfort fan speed modulation
(Remote Fan Kit RFK3002R or
RFK3004R required)
5. Battery backup for the main
burner during power outage
Before You Begin
Ensure that the power supply
has been turned off at the
breaker or fuse before beginning
the installation.
Shut o the gas supply at the
shut-o valve, and ensure that
the main burner and pilot light
have been turned o and the
replace has been cooled o
for at least two hours before
installation.
Tools Required
• T20 Torx bit
• Impact gun / Drill
• 1/4 " Nut driver bit
Contents
A. Disconnect Control Module and Harness: .........................................3
B. Stepper Motor Installation: ..................................................................3
C. Control Module Installation: ................................................................4
D. Main ON/OFF Switch Installation: .......................................................5
E. Battery Holder Installation: ..................................................................5
F. Operation with Backup Battery: ...........................................................6
G. Operation with MAIN Power: ...............................................................6
H. CPI / IPI Jumper Cable Installation ......................................................7
KIT # Contents
RX200NG
RX300NG
Control Module, Remote Control, Stepper Motor-NG,
Manual Override switch with harness and bracket,
backup battery pack, Proame 2 operations manual,
hardware and batteries.
RX200LP
RX300LP
Control Module, Remote Control, Stepper Motor-LP,
Manual Override switch with harness and bracket,
backup battery pack, Proame 2 operations manual,
hardware and batteries.
Note: You may remove the front cover (See Figure 2), or the
burner assembly to access the control module and wiring. If
removed, please ensure it is re-installed properly and all gas
connections are leak tested.
Remote Control
Control Module
Battery
Pack
Manualoverride
switch with harness
andbracket
Stepper
Motor-NG
or LP
Proame2
Operations Manual
Figure 1 Contents of Proame 2 Upgrade Kit
Hardware and
batteries
Figure 2 Fireplace front cover

XT0016 3
Installation
RX 200
Control Module Disconnect RX 200 Stepper Motor Installation
A. Disconnect Control Module and Harness:
1. Disconnect Control Module Powercord from the PPO box.
B. Stepper Motor Installation
1. Using a Torx T20 or slotted screw driver, remove the two screws that
are attached to the Hi-Low knob on the Gas Control Valve (Figure 7)
and discard the screws and the knob. Remove gasket and discard.
2. Disconnect Spark Wire and Sensor Wire from connectors X2 and X3
of the control module.
3. Disconnect the wall switch harness from X4 Control Module and
discard.
4. Remove the Valve Harness from X5 of the control module.
5. Remove the connector from X1 of the control module.
6. Remove the control module from rebox compartment and discard.
Note: module is attached by velcro strips.
Figure 3 Powercord in PPO box
Figure 4 Control module with wires
Figure 5 X5 plug of control module
Figure 6 X1 plug of control module
Figure 7 Replace Hi-Lo knob on valve
Figure 8
Discard spring
and gasket
Discard knob
and screws
Figure 9 Stepper Motor - LP Figure 10 Stepper Motor - NG

XT00164
Installation
RX 200
Control Module Installation
C. Control Module Installation
1. Position the new control module on the replace oor ( the red
switch "SW1" must be towards the front of the replace).
2. Connect the Power Plug to X1
2. Ensure the pretted rubber gasket is properly positioned (Figure
11 - D). Otherwise, t the gasket as shown.
3. Position the stepper motor on the gas control valve as shown in
Figure 12 - E.
4. Manually thread the two supplied mounting screws into the valve
body. Use a torque screw driver with Torx T20 bit, to tighten the two
screws to a torque setting of 25 lb-in +/- 5%.
5. Install the enclosed identication label to the valve body Figure 12
- G.
Figure 11 Stepper Motor Installations
Figure 12 Label Installation
Figure 13 Identication Label
- NG
Figure 14 Identication Label
- LP
Figure 15 New Control Module
Figure 16 X1 plug on control module
3. Connect the Spark and sensor wires to X2 and X3
4. Connect the Manual ON/OFF switch to X4
5. Connect the Valve Harness to X5
6. Connect the Stepper motor harness to X6
7. Attach the Control module to the bottom of the rebox using the
velcro strips supplied.
Figure 17 X2 > X6 plugs on control module

XT0016 5
Installation
RX 200
ON/OFF Switch Installation RX 200 Battery Holder Installation
D.Main ON/OFF Switch Installation:
1.Position the Main/o Switch bracket on the right leg of the rebox.
2. Using the two selftapping screws supplied attach the bracket.
3. Feed the switch and the wires through the slot in the bracket as
shown and install the switch to the bracket. See Figure 21.
4. Secure the wires to the oor of the replace using the supplied cable
tie and cable tie mounts.
5. Attach the "Main ON/OFF" sticker supplied to the switch bracket.
E. Battery Holder Installation:
1. Secure the battery holder to the replace oor using the supplied
velcro strips. See Figure 22.
Note: The velcro strips act as an electrical isolation, do not attach
the battery holder to any metal part without using the velcro strips,
or the control module will be damaged.
2. Connect the red and black wires from the battery holder to the red
and black wires from the valve harness. See Figure 23.
Figure 18 Attach switch bracket to front of replace
Figure 19 Attach switch bracket to front of replace
Figure 20 Attach switch to bracket.
Figure 21 Attach switch to bracket.
Figure 22 Battery holder
Figure 23 Battery holder wires

XT00166
Installation
RX 200
Operation w/ Backup Battery RX 200 Operation with MAIN Power
F. Operation with Backup Battery:
1. Install the four supplied AA batteries to the battery holder.
CAUTION: Please note battery orientation while installing them.
Incorrect orientation may damage battery, cause re hazard and
the replace may not function properly.
2. Follow the instructions on the "Proame2 Operation and Maintenance
Manual- XG0677" to install batteries on the remote control.
3. Turn the gas supply ON.
4. Program the remote control to the control module (see "Proame2
Operation and Maintenance Manual- XG0677").
5. Check the stepper motor for gas leaks and ensure no leak.
5. Turn the replace ON and modulate the ame using the remote
control and ensure proper operation (see "Proame 2 Operation
and Maintenance Manual XG0677").
Blue Back lit LCD display
On/OKey
Thermostat Key
Up/Down Arrow Key
Mode Key
Figure 24 Proame Remote Control
G. Operation with MAIN Power:
1. Remove the four batteries from the battery holder
2. Plug the Control Module Power cord to PPO box. See Figure 3.
3. Turn the replace ON using the remote control and conrm
operation with main power ON.
Note: You may re-install the backup batteries to the battery holder
at this point to ensure that replace is operational during power
outage. It is recommended to check and replace the backup batter-
ies at least once a year. More frequent battery replacement may be
required in case of extended operation on backup batteries.

XT0016 7
Installation
CPI [Continuous Pilot Ignition] / IPI [Intermittent Pilot
Ignition]JumperCableInstallation
“Why use CPI mode”?
There are several reasons why you may choose to use CPI mode. When
a ue is cold it can be dicult to light the appliance. It can take a bit of
time (particularly on tall vents) to initialize vent action. This can result
in “lifting” or “ghosting” of the ames during the rst two to three
minutes of operation. It is also possible to encounter times when the
replace fails to light successfully. The replace will then attempt to
re-light a second or third time depending on prevailing temperatures
or altitude. When in CPI mode the pilot also keeps the system warm.
During a “cold” start, condensation will normally form on the inner glass
surface of the door. This condensation will quickly dry, however, the
condensation tends to run down the glass and cause some streaking.
CPI mode helps to resolve this issue. If CPI mode is used during the
winter months the energy it takes to run the pilot is partially recovered
as heat into the building, so it does not waste as much energy as running
a pilot in the o season.
A connector is supplied with this unit that can be plugged into the
wire harness connected to the controller. This Jumper Cable gives the
Remote Control the ability to operate the CPI / IPI switch and set the
unit to operate in either condition. CPI means “Continuous Pilot Ignition”
or “Standing Pilot” as it is commonly known. IPI means “Intermittent
Pilot Ignition”, which only initializes the pilot when you are going to be
using the appliance.
ThedifferencebetweenIPIandCPI:
IPI (Intermittent Pilot Ignition) Mode: is a fuel saving mode in
which the pilot is only used when the main burner is on.
CPI (Continuous Pilot Ignition) Mode: The pilot runs continuously
even when the main burner is o. (Typically only used for winter
months)
InstallingtheCPIJumperCable
1). Open the control box drawer.
2). Remove the bag containing the Jumper Cable from the wire
harness connected to the controller.
3). Find the corresponding plug attached to the control wire harness
and connect the CPI jumper.
4). See operation section to turn remote into CPI mode.
Figure 19. Open the control box drawer
Figure 19.b Locate Jumper cable
Figure 19.c Connect CPI

XT00168
Installation
RX300
Control Board upgrade/replace
1. Remove existing basic board drawer by unplugging all existing
connections.
When upgrading the
Distinction control board,
the board will be shipped
with the board installed in
the drawer and with the
appropriate cables installed.
2. Unplug PPO from board located underneath the pilot
assembly. Disconnect the ground and remove drawer
completely.
3. Discard old drawer and wall switch and valve wires.
4. New Board.
On/O
Switch
PPO &
Ground
Fans LED
Pilot
D6315 (ST) (N/L) I-2 Wiring Diagram
1.5V AA type 1.5V AA type 1.5V AA type 1.5V AA type
WHITE
BLACK
BLACK WHITE GREEN
Lights
ON/OFF
CONTROL
MAIN Power 120VAC 60 Hz 6 Amps
SPARK SENSOR
RED BLACK
BATTERY
PACK
MAIN ON/OFF
SWITCH
YELLOW/GREEN
PILOT
R
ORANGE GREEN BLACK BROWN YELLOW ORANGE
6 10 6
OPTIONAL CPI/IPI SWITCH WHITE
LED Lights LED1 - Red LED LED2 Amber LED
SW1
LED
otroer
LED power
spp y
white white white
  
BLACK WHITE
VARIABLE SPEED
COMFORT FANS
Multicolored LED Lights
Fan Kit only available in Single sided version
Optional CPI/IPI Jumper
Multicolored
LED
Controller
Multicolored
LED Power
Supply
Figure 24. Remove existing basic board
Figure 24.b Remove existing basic board
Figure 24.c Proame2 Board
Figure 24.d D6315 (ST) (N/L) I-2 Wiring Diagram
Adding options to DL units
requirescontrolboard
upgrades for the following
options
Fan Kit DFK-3
LED Kit MCLEDDL63
Remote Control
Stepper Motor
Powervents

XT0016 9
Installation
5. Feed On/Off switch
through drawer frame
6. Feed Fan, LED, PPO, and
pilot wires through drawer
frame.
7. Disconnect On/Off switch and feed cable through drawer
frame. Install in space on left inner wall.
9. Place on LED wire on rightside firebox floor with adhesive wire
pad. For LED Install instructions see OptionalLEDkitInstall/
Replace instructions
10. Loop Pilot wires from behind control board drawer to the
front. Plug into X2 and X3
8. Place Fan wire on leftside firebox floor with adhesive wire pad.
For fan Install instructions see OptionalfankitInstall/Replace
instructions
11. Valve wires are plugged into the valve in the Green, Red, and
yellow ports respectively.
Figure 24.e On/O switch through drawer Figure 24.i LED wire
Figure 24.j Pilot wires
Figure 24.k Valve wires
Figure 24.g On/O switch
Figure 24.h Fan wire
Figure 24.f Fan, LED, PPO, and pilot wires
through drawer

XT001610
Installation
RX300
Optional stepper motor install/replace
Verify that the following items are present in the package.
• Pressure regulator assembly (E)
• Two (2) screws (F)
• Identification label (G)
• Installation instructions
1 Shut off the gas supply to the valve and shut down the electric
supply
2 Using a Torx T20, or slotted screwdriver, remove and discard
the two (2) pressure regulator mounting screws (A), pressure
regulator tower (B), and the spring and diaphragm assembly
(C), (If applicable).
3 Access gas valve by removing the valve blind
4 Ensure the rubber gasket (D), which is prefitted as part of
assembly (E), is properly positioned, otherwise fit the gasket
as shown.
5 Install the new STEPPER MOTOR pressure regulator assembly,
as shown in Fig. 3 and Fig. 4. Use the supplied screws (F)
6 Manually thread the two conversion kit mounting screws into
the valve body. Use a standard screwdriver or T20 Torx bit and
tighten to the screws with a fixing torque of 251b-in ± 5%.
INTHEEVENTTHATTHETHREADSOFTHEVALVEARESTRIPPED
ORDAMAGED,REPLACETHEVALVE.
7 Install the enclosed identification label (G) to the valve body
where it can be easily seen.
8 Make STEPPER MOTOR and valve electrical connections, apply
gas to system and relight appliance according to manufacturers
instructions.
9 With the main burner "ON", test the new pressure regulator
assembly for leaks using a soap solution.
9 Relight the main burner and verify proper burner ignition and
operation
WARNING!
Do not use power drill.
WARNING!
Installation should be carried out in a clean environment.
WARNING!
This modulating conversion kit must ONLY be applied as part of a
conversion kit supplied by montigo for the specic appliance, and type
of fuel, being converted.
WARNING!
Correct operation of the system cannot be guaranteed if the conversion
kit or valve has been dropped or has sustained a strong impact.

XG2021 11
Notes

XT0016
Installation & Maintenance Manual
PROFLAME 2 UPGRADE KIT
RX 200 NG/LP
RX 300 NG/LP