Montigo L42DF series User manual

Burner Tray Gasket
17
Thiskitshouldbeinstalledbyaqualiedperson.
Checklocalcodesandreadallinstructionspriortoinstallation.
CAUTION:
Ensurethatpowerisoffat
theelectricalbreakerorfuse
beforebeginninginstallation.
 EnsuretheGasisoffatthe
shut-offbeforebeginning
installation.
InstallingtheHFK-SeriesCross-FlowBlower
forusewith:H-SeriesDF/
DL&L-SeriesDFGas
Fireplaces
H34-DF/DL;L38-DF
H38-DF/DL;L42-DF
H42-DF/DL;L52-DF
GeneralInformation
Thisblowerkitisforinstallationonthefollowingmodels:
CasaH34DL/H34DF
VillaH38DL/H38DF
EstadoH42DL/H42DF
L38-DF,L38-DF-I,L38-DF-A,L38-DF-F
L48-DF,L42-DF-I,L42-DF-A,L42-DF-F
L52-DF,L52-DF-I,L52-DF-A,L52-DF-F
KIT# Contents
HFK34 2xblowers,1xfancordassembly,4xmountingscrews
HFK34H 2xblowers,1xfancordassemby,4xmountingscrews,
1xheatsensorswitch
HFK42 2xblowers,1xfancordassembly,4xmountingscrews
HFK42H 2xblowers,1xfancordassemby,4xmountingscrews,
1xheatsensorswitch
BeforeYouBegin
Ensurethatthepowersupplyhasbeenturnedoffatthebreakerorfuse
beforebeginningtheinstallation.
Shutoffthegassupplyattheshut-offvalve,andensurethatthemain
burnerandpilotlighthavebeenturnedoffandthereplacehasbeen
cooledoffforatleasttwohoursbeforeinstallation.
Installation
1a. ModelsH34DL,H38DL,andH42DL:Removethelowerlouvresto
gainaccesstothecontrolcompartment.GotoStep2.
1b. ModelsH-SeriesandL-Series:Removetheglassdoortogain
accesstothecontrolcompartmentthroughtherebox.
2 Removetheaccessoriesinsidetherebox;logset,glasspebbles,
ordecorativeriverrocks,etc
3. Carefullyremovethedecorativehorizontalinsulationpanels.
Figure 2. Shutoffanddisconnectthegassupply.
Note: Followtheshut-downproceduresforthevalveinstalledwith
yourreplace.May not be exactly as shown.
(H34DF,H38DF,andH42DFModelsOnly)
Gas Valve Pan Base
Gas Inlet
Valve Bracket
 NOTE:DONOTCONTINUEUNTILTHISSTEPISCOMPLETED.
®
C
US
Figure 3.Removingtheburnertray.(H34DF,H38DF,andH42DF
ModelsOnly)
5. Removetheburnertrayasshowningure3fortheH-DLSeries
gasreplace,andgure3afortheL-SeriesDFreplace.
4. Shutoffthegastoyourreplaceandshutoffthecontrolvalve.See
theinstructionontheplacardsuppliedwithyourreplace.

18
Burner Tray Gasket
XG0625-081008
Figure 6. Installingtheheatsensor.
Heat sensor Blower power cord
6. Installtherstblowerontheleftside.Attachtheconnectionson
thefancordwiththeconnectionsontheblower.OnmodelsH34-
DL,H38-DL,andL42-DL,slidetheblowerscarefullyintoplaceto
therightofthevalve.Takecarenottodamageanypilottubingor
gascontrols.OnmodelsL38-DFandL-42-DF,slidetheblowerinto
placecarefullythroughtheopeninginthebaseoftherebox.
7. Installthesecondblowerontherightside.Attachtheremaining
connectionsonthefancordwiththeconnectionsontheblower.
OnmodelsH34-DL,H38-DL,slidetheblowerscarefullyintoplace
totherightofthevalve.Takecarenottodamageanypilottubing
orgascontrols.OnmodelsL38-DF,L42-DFandL-52-DF,slidethe
blowerintoplacecarefullythroughtheopeninginthebaseofthe
rebox.
Figure 4. Positioningtheblowerontheleftside.
Figure 5. Positioningtheblowerontherightside.
InstallingtheHFK34/HFK34HCross-FlowBlower
Plugtheblower'spowercordintothereceptacleonthePPO
box.
10. InstalltheheatsensorswitchcontainedintheHFK34Hblower
kit:
OnmodelsH34DF,H38DF,andH42DF,reinstalltheburner
trayasoutlinedinstep1bandshowningure2.
Installtheheatsensorswitchbyslidingitintoplaceunder-
neaththeburnertraytotherightofthegasvalve,asshown
below.
11. OnmodelsH34DF,H38DF,andH42DF,CAREFULLYreinstall
thelogbaseandlogsetandensurethattheyareproperlypo-
sitionedasoutlinedinthereplace'soperationandinstallation
manual.Oncethelogsetinproperlypositioned,replacethe
glassdoor.On-L-Seriesmodelsreplacetheceramicpanel(s),
decorativebeads,and/ordecorativerocks.
12.Replacethedoorasshowninyourinstructionguide.
13. Turnonthepowersupplyandreconnectthegassupply.
8. Oneachblower,positiontheinsideofthefronttopedgewith
themountingbracketsoneachsideofthecontrolcompart-
ment,asshowningures4and5.Fastenbothblowersin
placewithselftappingscrews.
9. IfthePPOboxhasnotbeenfactoryinstalled,ensurethatthe
householdelectricalsupplyisshutoffatthebreakerorfuse,
andconnectthetwowireleadsfromtheboxtothehousehold
electricalsupply.InsertthePPOboxintothesquareholein
theright-handsideofthecontrolcompartmentandscrewinto
place.
Figure 3a.Removingtheburnertray.(L38DF,L42DF.L52DFOnly)
Sensor
Mounting Plate