Moons' Applied Motion Products SWM24 User manual

Requirements
▪A 12-70V DC power supply.
▪A personal computer running Microsoft Windows 98, 2000, ME, NT, XP, Vista or 7/8/10/11.
▪ST Congurator™ software (available at www.applied-motion.com/products/software).
▪A 3004-277-5M power cable, 3004-290-5M I/O cable, or a 3004-280-5M Ethernet cable, as needed.
▪NOTE: Cables are NOT included and must be purchased separately.
▪For more detailed information, please download and read the SWM24 Hardware Manual, available at www.applied-
motion.com/support/manuals.
To begin, make sure you have the following equipment:
Step 2
DO NOT apply power until all connections to the drive have been made.
a)Download and install the ST Congurator™ software.
b) If you intend to connect the drive directly to your PC, congure your computer to use IP address 10.10.10.11. (For
instructions on connecting your STM drive to a local area network (LAN), please consult the STM23 Hardware
Manual)
c) Do not connect the Ethernet cable to the SWM24 before applying power. This will cause the drive to use its
recovery address, thus assigning itself IP address 10.10.10.10. (See the SWM24 Hardware Manual for further
details on selecting IP addresses for the drive and PC)
d) Launch the software by clicking: Start / All Programs / Applied Motion Products / ST Congurator
Step 1
Wire the drive to the DC power source.
(Do not apply power until Step 3)
Note - the SWM24 accepts DC voltages from 12-70V. If using
an external fuse, we recommend a 5 amp fast acting fuse.
(See the SWM24 Hardware Manual for more information about
power supply and fuse selection.)
Connect I/O, if required by your application. A 3004-290-5M
cable will be required.
(See the SWM24 Hardware Manual for more information about
wiring I/O to the SWM24.)
GND
EMI Filter
AC
Power
Input
LINE
LOAD
L
NN
L
V+
V-
P/N:092.00823.00 (LCR)
4
3
1
2
POWER
DC POWER
SUPPLY V-
V+
V+
V-
GND
920-0070 Rev C
SWM
SWM24 Ethernet Quick Setup
Guide
PIN SIGNAL WIRE COLOR
1 DC + BRN
2 DC - WHT
3 DC + BLU
4 DC - BLK
METAL HOUSING FRAME GND & SHIELD SHIELD
CONNECTION CHART

Step 3
If you have any questions or comments, please call Applied Motion Products Customer Support:
[phone], or visit us online at applied-motion.com.
18645 Madrone Pkwy
Morgan Hill, CA 95037
Tel: [phone]
applied-motion.com
a) Apply power to the drive. Wait approximately 5 seconds, then connect the
Ethernet cable to the network. In the absense of a valid network connection
the drive will default to its recovery address, 10.10.10.10.
b) Select the “Ethernet” radio button in the center of the screen and specify the target
IP adress of 10.10.10.10. Click ‘Upload from drive’. If successful, you should see a
screen similar to that shown below, allowing the user to fully congure the drive.
c) To specify a new IP address for the drive, select “Drive” --> “Edit IP Address
Table” from the drop-down menus at the top of the screen.
d) Click the “Read from Drive” button to refresh the list, noting that only the
rst entry may be edited. Specify a new IP address in these elds.
e) Follow the conguration instructions in the ST Congurator™ screens. The ST Congurator™
software can be used to set up your drive to operate in several di󰀨erent modes including: pulse
& direction, velocity (oscillator), streaming commands (SCL), and Q programming mode.
f) ST Congurator™ includes a self test option (under the Drive menu) to verify
that the SWM24 and power supply are correctly wired and congured.
g) Once congured, use the ‘Download to Drive’ button to permanently save the conuration to the drive.
h) Note that if connected to the network when power is applied, the drive will use the
IP address specied in the IP address table, position 1 (see step D above). If not
connected to a network, the drive will default to the recover address of 10.10.10.10. This
feature allows a user to connect to a drive even if its IP address is not known.
920-0070 Rev C
SWM24 Ethernet Quick Setup Guide