Mopar 82208859 User manual

INSTALLATION INSTRUCTIONS
Professional Installation Is Recommended
Technical Support
For Authorized Dealers - (800) 34-MOPAR
Hours: 9:00 a.m. - 6:00 p.m. EST Monday thru Friday
10:00 a.m. - 2:00 p.m. EST Saturday
1030191
REV.B
10/04 K6859230
Système de démarrage à distance
NOTICE D’INSTALLATION
Installation par un spécialiste conseillée
Jeep
Grand Cherokee (WK)
Remote Start System
Warning! Remote Start Systems are only appli-
cable to vehicles with automatic transmission!

2
This device complies with part 15 of the FCC rules and with RSS-210 of the
industry Canada. Operation is subject to the following two conditions: (1) this
device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation.
This product was manufactured in environmentally friendly manufacturing
facility and may contain certain recycled materials. All materials meet or
exceed original specifications for quality and reliability.
Jeep Grand Cherokee (WK)
Remote Start System
Table of Contents
VehiclePreparation..................................................................................4
ModulePreparation..................................................................................5
ComponentInstallation.............................................................................6
SystemProgramming.............................................................................10
SystemTesting.........................................................................................13
ServiceMode...........................................................................................13
Reassembly..............................................................................................14
OptionBankChart...................................................................................15
Troubleshooting........................................................................................16
ChangingTransmitterBatteries.............................................................16
SystemLayout..........................................................................................17
The soldering procedure illustrated below must be followed when perform-
ing wire connections under the hood. Failure to use this procedure could
result in improper performance of the remote start system.

3
PARTS REQUIRED
Part Number 82208859
5 AMP 1X 15 AMP 4X
WARNING: / AVERTISSEMENT
This vehicle is equipped with a remote controlled engine starter.
To reduce the risk of serious Injury or death, switch engine starter
system into service mode and disconnect the vehicle battery
before performing any service on the vehicle.
Ce véhicule est doté d'un démarreur à distance. Pour réduire les
risques de blessures graves ou mortelles, mettre le démarreur à
distance en mode service et débrancher la batterie du véhicule
avant d'effectuer des travaux d'entretien sur celui-ci.
Owner's Manual
VehicleRemote Start System
TM
FeaturingPowerCodeTechnology
FortheUltimate inComfort,Convenience andSecurity
TM
®
1024256 12/03
Remote Control
CarStarterSystem
Remote Start
Activation
2X
Remote Start
Shutdown
2 sec.
2X 4X 10X
2X
Part Number 82208994
TOOLS REQUIRED
10mm 1/4”
RTV SEALENT
VEHICLEPREPARATION
1. Lower one or more of the passenger windows so the keys do not get locked
in the vehicle.
2. Disconnect and isolate the negative battery cable. The battery will need to be
re-connectedbeforeprogramming.
3. Vehicle requires 2 valid Sentry Keys present at the time of installation.
2X(French&English)

4
Vehicle Preparation
1. Remove driver’s side lower dash
panels, located directly under the
steering column and ignition switch
bezel.
A.Pull downlowerdash &remove.
B.Remove (2)screwsfrom black
underdashpanel& remove.
C.Removeignitioncylinder cover.
Carefullypry off usinga small
screwdriveror similar tool. Do not
damagethepanel.
Overview
The remote starter module harness will interface with the existing WK ignition
switch connector, two center-splice connections, three butt connections, and a
groundtermination. Four wires willberouted through thecowl panel, to ahood-
mounted safety switch, horn, parking light, and tachometer connections.

5
Module Preparation
1. Place fuses into the control module.
A.Observefuseamperageratings.
Place the 5 Amp fuse into the
“MainB+” location. Populatethe
remaining fuse locations, as
shown in the diagram, with the 15
Amp fuses. Ensure the 15Amp
fuse is placed in the “OPEN”
locationnext to “PK LIGHTS”.
2. Install DNA into the control module
A. Insert DNA into the control module.
Ensure the DNA assembly snaps
completely in place.
DNA

6
Component Installation
1. Install Hood Safety Switch.
A.Using (2) of thesupplied1/4”
screws, secure hood safety switch
ondriver’sside rear cornerof hood
perthediagram. Note:Wire exits
top of switch. Switch must be
bentat 45degree angle.
B. Route the hood safety switch
wiringundertheenginecompart-
mentcover panel asshown in the
diagram.
C. Using a supplied 1/4” screw,
securethe ground leadfrom the
switch to the cowl as shown in the
diagram. Theremaining wirewill be
connectedlater.
D. Locatea visible areain the frontof
theengine compartmenttomount
theunderhood warningsticker as
shownin thediagram.
2. Install Dipole Antenna
A.Mount dipole antenna tothe
windshieldabovetherearviewmirror
andbelow theblack windshield
trim.
B.Run theantenna wire abovethe
headlinertothe driver’sA-pillar.
Temporarilyremove theA-pillar
rubbergasket andruntheantenna
leaddown through the left side
dashopening. Replace therubber
gasket. Ensure the antenna is
securelytuckedabovethehead-
liner and is not visible along the
entirelength.

7
B.Connect theharness5-way female
connector to the vehicle’s ignition
switch.
C. Connect the harness 5-way male
connectorto thevehicle’s 5-way
ignitionconnector previously
removed from the ignition switch.
D. Usinga supplied 1/4”screw,secure
theblack ground wirewith ring
terminal to the metal under dash
braceas shown indiagram.
3. Install Custom Harness.
A. Locate ignition switch connector,
directly behind the ignition switch.
Releasethe redsecondary lock.
Whilepushing onmain release,
removeconnector fromignition
switch.
E. Run the harness White/Green wire
to the brake switch. Connect by
center-splice to the White/Green
wirein Cavity #2of the grey6-way
brakeconnector,followingthe
center-spliceprocedureabove.
Secure wire to the factory wire
harness with a wire tie as shown.
Caution: Keep wire away from
the exposed steering column!
Caution: Do not remove the
brake lamp switch from the
mounting bracket. If the switch
is removed from the mounting
bracket, it MUST be replaced
with a new switch.
Center-SpliceProcedure

8
G. Using the supplied butt connector,
connect the Black/White wire to
theremainingwire fromthe hood
safety switch.
H. Route the Dk Blue/Yellow wire to
the top of the engine at the coil
connection point as shown. Cen-
ter-splice the Dk Blue/Yellow wire
to the Dk Blue/Yellow wire at the
coil,following thecenter-splice
procedureon page 7. Solderthe
connection
I. Route the Green and Yellow wires to
therelay junction boxon the driver
sideof theengine compartment.
Removethe hornrelay asshown in
thediagram. Slidethe supplied Green
wirerelayterminalconnectorover
terminal 85 (pin #1) of the relay as
shownin thediagram.
Remove the parking light relay as
shown in the diagram. Slide the
Yellow wirerelay terminal connector
overterminal85 (pin#1)ofthe parking
light relay as shown in the diagram.
Re-insert the relays into place.
Routethe wiringfrom the relay
connectors out of the junction box
andconnect the Greenwire of the
jumperto the Greenwire of the
harness using the supplied butt
connector. Connect theYellow wire
of the jumper to theYellow wire of the
harness using the supplied butt
connector.
F. Route the four remaining wires
(Black/White, Green,Yellow, and
DkBlue/Yellow) throughthe cowl
paneland intothe enginecompart-
ment.
123456
123456
PIN#1
Horn & Parking Light Jumper (included)
1234567
1
23456
7
1234567
HORN
12345678
1
234567
8
12345678
PKLTS

9
4. Install SKREEM Interface Module.
A. Following the directions on the
suppliedampule ofadhesive
primer, apply a thin coating of
primer to the entire SKREEM
transceiverantenna coil. Allow the
primerto dry for5 minutes before
proceeding to the next step. Note:
Use goggles and gloves to
protect yourself from any acci-
dental contact.
B. Remove backing from one side of
thesupplied two-waytape and
applytapearound thetransceiver
antennacoil.
C. Routethe antennaloop fromthe
SKREEMInterface moduletothe
ignitioncylinder.
D. Removethe remainingbacking on
thetape and positionthe antenna
loopon the tapearound the
transeiverantenna coil. Ensurethe
red stripe faces out towards the
key. Press down on antenna coil
toensure a strong bond.
E. Using a supplied tie wrap, secure
theantenna coil asshown.
K. Connectthe 24-wayand10-way
connectorsinto thePC-12 Remote
Start module. Also, connect the 2-
wayantennaconnector (onend
oppositethe mainharness connec-
tions).
24-Way 10-Way
Antenna

10
1. Transmitter Programming.
A. Make sure battery is connected.
B.Close hood.
C.Turn theignition tothe “on”position.
D. Press and hold the programming button. After 10 seconds the horn will
chirp and the lights will flash 3 times indicating the system is now in
transmitterlearn mode.
E.Releasethe programmingbutton.
F. Press button on transmitter to be programmed. The horn will chirp and the
lights will flash 1 time indicating that the transmitter has been learned.
G. Repeat step F for additional transmitters.
2. Option Programming.
The remote start system has several installer programmable options which
can be changed to accomodate different circumstances. In most cases, there
will be no need to change any default settings. There will be cases (such as
deisel vehicles), where the delay before crank option must be set.
Note:
This system has 2 option banks. Bank 1 has 7 options, and Bank 2 has 2
options. Refer to the Options Bank Chart on page 15 for details.
A.Follow the steps abovetoenterTransmitterLearn Mode.
B.Press and releasethe programming button. The hornwill chirp andthe
lights will flash 4 times indicating the system has entered Option Bank 1.
C. Press and release the brake pedal. The horn will chirp and the lights will
flash 1 time indicating the system is at option 1. Additional press and
releases of the brake pedal will advance to the next option. The horn will
chirp and the lights will flash according to which option is selected (i.e.
Two chirps and flashes indicates option 2).
D. Pressing the transmitter button changes the setting of the option. The
status LED (located in the main harness approximately 4” from the
module) indicates the setting of the option. LED “on” indicates the option
is on, LED “off” indicates the option is off.
System Programming
Notes:
1. Reconnectthe negativebattery terminal priorto programming.
2. Up to a total of 8 transmitters can be programmed into memory.
3. Transmittersshipped with complete kits arepre-programmed to the
DNA and do not need to be programmed at this time.

11
Option Programming - continued.
E. Pressing and releasing the programming button again will put the system
into Option Bank 2. The horn will chirp and the lights will flash 5 times
indicating the system has entered Option Bank 2.
F. Press and release the brake pedal to cycle through the options in Bank 2.
Notes:
1. Once the system has reached the last option in a bank, pressing and
releasing the brake pedal will return back to option 1 in that bank.
2. Once the system has reached Option Bank 2, pressing and releasing the
programming button will return back to Option Bank 1.
3. To reset options back to their default setting, while in option learn mode,
push and hold the transmitter button until the horn chirps and lights flash
5 times.
3. Tach Rate Programming (Required for system to operate).
A.Close hood.
B.Turnthe ignitionto the “on”position.
C. Press and hold the programming button. After 10 seconds the horn will
chirp and the lights will flash 3 times.
D.Releasetheprogramming button.
E.Press and releasethe programming buttonagain. The hornwill chirp and
the lights will flash 4 times indicating the system has entered Option
Bank 1.
C.Press andrelease the programmingbutton again. Thehorn will chirpand
the lights will flash 5 times indicating the system has entered Option
Bank 2.
D.Advance to option 2 by pressing and releasing the brake pedal 2 times.
The horn will chirp and the lights will flash 2 times indicating sthe system
is at option 2.
E. Start the vehicle with the key. The horn will chirp and the lights will flash
once approximately every 3 seconds indicating a valid tach signal.
F. Once the engine has settled to a normal idle speed, press and release the
brake pedal to set the tach rate.
G.Turn the ignition off.
Note:
If the system is not chirping the horn and flashing the lights every 3 seconds
after the ignition has started, the system is not seeing a valid tach signal.
Check your tach connection (Dk Blue/Yellow at coil). Repeat the
TachRateProgrammingprocedure.
Tach Rate Programming must be done before the SKREEM
learn procedure.

12
E.Approximately 10 seconds after the ignition has been activated by the
second Sentry Key, the dash theft-security light will start to flash, and a
single audible chime (not the key-in-cylinder chime) will sound to indicate
thatthe systemhas entered“Customer Learn” programmingmode.
F. Cycle the ignition switch back to the “off” position. Remove the key and
keep it at least 2 feet away from the ignition switch. Theft-security light
willturn off.
G.Press and release the programming button located on the custom har-
ness.
H. Within 60 seconds, press the start button on the remote start transmitter
(2) times.
I. Approximately 10 seconds after completion of Step H, a single audible
chime will sound and the theft-security light will stop flashing and stay on
solid for 3 seconds, and then turn off to indicate that the SKREEM
Interface module has been successfully programmed.
J. The system will remote start the engine approximately 15 seconds after
Step H. Press the brake pedal to shut down the remote start system.
4. SKREEM Transponder Interface Programming.
2 programmed Sentry keys are required for this step!
NOTE: Review and understand steps A-J prior to performing.
A. Close hood.
B. Insert one of the two valid Sentry Keys into the ignition switch and turn
the ignition switch to the “on” position.
C. After the ignition has been activated for more than 3 seconds (but no
more than 15 seconds), cycle the ignition switch back to the “off” position.
Remove the key and keep it at least 2 feet away from the ignition switch.
D. Within 15 seconds of removing the first key, insert the second valid
Sentry Key into the ignition switch and turn the ignition switch to the “on”
position.
Note:
In some vehicles, during the SKREEM Interface learn procedure, the
vehicle will start and stall on the first remote start attempt. The second
remote start attempt will be successful. This is a normal condition of
thelearn procedure. If thevehicle does notstart, refer tothe Trouble-
shootingguide onpage 16.
Once a SKREEM Interface Module has been programmed to a
WCM/vehicle, it is permanently assigned to that WCM/vehicle and
cannot be used on any other WCM/vehicle.

13
1. Use the following checklist to ensure all features function as indicated.
SystemTesting
Remote start - Press start button 2X.
Remote stop - Press and hold start button for 2 seconds.
Hood safety switch shutdown - While under remote start, open hood - engine should shut down.
Brake safety shutdown - While under remote start, press brake - engine should shut down
Key-in-sense circuit - With key in the ignition cylinder, remote start should not activate.
Overrev shutdown - While under remote start, press accelerator - system should shut down at 3X idle.
Service Mode - With ignition turned on with key, press remote start button 3X. Repeat to exit Service Mod
e.
Heater/Air Conditioning - Ensure Heater/AC works during remote start.
Service Mode
Service mode is used whenever it is necessary to disable the remote start
feature, such as during vehicle service. The vehicle will not start by remote if
Service mode is activated.
1. Entering Service mode.
A. Turn igntion on with the key.
B. Press the start button on the remote transmitter 3 times. 2 seconds later,
the horn will chirp and the lights will flash 3 times, indicating the system
is in Service mode.
C. While in Service mode, whenever a remote start attempt is made, the
horn will chirp and the lights will flash 3 times alerting the user that the
system is in Service mode.
2. Exiting Service mode.
A. Turn igntion on with the key.
B. Press the start button on the remote transmitter 3 times. 2 seconds later,
the horn will chirp and the lights will flash 1 time, indicating the system
has exited Service mode.

14
2. Dashreassembly.
A.Reverse the dashdissassembly procedure.
Reassembly
1. Module & Harness mounting.
A. Using supplied wire ties, secure the remote start module to existing
wire harnesses under the left side of the dash.
B. Using supplied wire ties, secure the SKREEM Interface module to an
existingwire harness underthe dash.
C. Using supplied wire ties, secure the main harness and SKREEM
Interfaceharnesses to existingwire harnessesunderthe dash.
Ensureno wires will become entangled inthe steering column
knuckle and that they are not visible to vehicle occupants.
D. Using a supplied wire tie, secure the programming button to the
harness leading to the vehicle’s diagnostic connector. Consistency
in mounting this switch in the same place every time, will make it
easier to find in case the system comes back for service. Also, the
dash will not have to be disassembled to access it.

15
Option Bank Chart
Option Bank #1 (4 chirps) Factory Setting
---------------------------------------------------------------------------------------------------------------------
1. Not used
Reserved for future upgrade feature......................................... .On
2. Not used
Reserved for future upgrade feature......................................... .On
3. Tach diagnostic mode
Thisfeatureshouldonlybe usedfor troubleshooting
purposes only!.......................................................................Off
4. Car start run time
LED “on” - 15 minutes, LED “off” - 10 minutes..........................Off
5. Not used
Reserved for future upgrade feature.........................................Off
6. Diesel timer
Delays crank attempt 30 seconds after ignition on....................Off
7. Horn pulse short/long
LED “on” - Short output, LED “off” - Long output.........................On
Option Bank #2 (5 chirps) Factory Setting
---------------------------------------------------------------------------------------------------------------------
1. Key-in-sense polarity
LED “on” - Positive, LED “off” - Negative.................................Off
2. Learn tachometer
Horn will chirp every 3 seconds, press brake to set idle speed.
---------------------------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------------------------------

16
1. Horn honks 4 times & vehicle does not start - no tach learned.
A. Ensure good connection at tach wire.
B.Re-program tach(seepage11).
Troubleshooting
2. Starter cranks too long.
A. Re-program tach - allow vehicle to come to a low idle during tach learn
procedure.
3. Ignition turns on, then horn honks 2 times & vehicle does not start - Key-
in-sense circuit activated.
A. Remove key from ignition cylinder.
B. Key-in-sense polarity set incorrectly. Program for negative input (see
optionchart page15).
4. Horn honks 2 times & vehicle does not start - safety input activated.
A. Ensure hood is closed.
B. Ensure hood switch is grounded and has a good connection.
C. Ensure brake switch is not depressed.
D. Ensure brake switch wire is connected to correct vehicle wire.
5. Horn honks 3 times & vehicle does not start - Service Mode engaged.
A.Disengage servicemode (seepage 13).
6. Vehicle starts then stalls - SKREEM Transponder Interface not learned.
A. Ensure 2 and 4 way connectors are connected
B. Ensure antenna coil is wrapped tightly around the ignition cylinder
SKREEMantenna ring.
C.Re-learnSKREEMTransponder Interface(seepage12).
Changing the Remote Control Battery; Mopar part # 05140773AA:
1. With a small flathead screwdriver, carefully pry the two halves of the remote
transmitter apart.
2. Gently pry the transmitter circuit board out of the case.
3. Slide the black battery holder out of the bottom of the circuit board. Do not
losethe black batteryholder.
4. Remove the old batteries and replace with new ones. Observe the (+) and (-)
signswhen removing the old batteries.
5. Gently snap the circuit board back into the transmitter case.
6. Carefully snap the case halves back together, then test the remote control.
It is not necessary to re-program the remote control after changing the
battery.
7. Horn honks 8 times & vehicle does not start - Safety feature - vehicle
will only remote start 8 consecutive times until the vehicle key is used.
A. Start vehicle with the ignition key to reset.

17
12345
12345
123456
1
2345
6
1
2345
6
1
2345
6
123456
SKREEM INTERFACE
MODULE
FACTORY HARNESS
BRAKE SWITCH
PR OGR AMMING
BUTTON
FACTORY
IGNITION
HARNESS
MAL E
IGNITION S WITC H
CONNECTOR
FEMALE
IGNITION S WITC H
CONNECTOR
82208859
PC-12 MODULE
DIPOL E ANTE NNA
REMOTE START DNA
05140471AA
LED
82209083
HOOD TILT
SWITCH (SUPPLIED)
GROUND
COWL PANEL
IGNITION C OIL
CONNECTOR
05140473AA
FACTORY HARNESS
Driver S ide E ngine C o mpartment P DC
Relay Pin85
Black/White
Module Dk B lue/Y ellow to
DkBlue/Yellow
to White/Green P in #2
05140470AA
SKREEM INTERFACE
LOOP ANTENNA
JEEP GRAND CHEROKEE (WK) SYSTEM LAYOUT
Module White/Green
Module Green
Horn & Parking Light Connection
Jumper 1028638
Relay
Module Yellow
Horn R elay
P arking Light R elay
Yellow
Green
Pin #1
Pin #1
123456
1
2345
6
123456

18
1030191
RÉV. B
10/04 K6859230
NOTICE D’INSTALLATION
Installation par un spécialiste conseillée
Jeep
Grand Cherokee (WK)
Assistance technique
Pour obtenir la liste des concessionnaires agréés - (800) 34-MOPAR
Horaires: de 9h00 à 16h00, heure de New York, du lundi au vendredi
de 10h00 à 14h00, heure de New York, le samedi
Système de démarrage à distance
Attention : les systèmes de démarrage à distance
s’appliquent uniquement aux véhicules à transmis-
sion automatique!

19
Jeep Grand Cherokee (WK)
Système de démarrage à distance
Table des matières
Ce dispositif est conforme à la partie 15 du Règlement de la FCC et au
RSS-210d’IndustrieCanada. L’utilisationestsoumiseauxdeuxconditions
suivantes : (1) Ce dispositif ne doit pas émettre de brouillage nuisible et
(2) il doit accepter toute interférence reçue, y compris celles
susceptibles de provoquer un fonctionnement indésirable.
Ce produit a été fabriqué dans une unité de production sans danger pour
l’environnement et pourra contenir certains matériaux recyclés. Tous les
matériauxutiliséssatisfont ouexcèdent les spécificationsd’origine enmatière
de qualité et de fiabilité.
Préparationduvéhicule..........................................................................21
Préparationdumodule...........................................................................22
Installationdescomposants...................................................................23
Programmationdusystème...................................................................27
Testdusystème.......................................................................................30
ModeService……………………………………..........…………….…30
Remontage……………………………………..................…………….31
Tableaudessériesd’options.................................................................32
Recherchedespannes………...........................................................…33
Changerlespilesdel’émetteur.............................................................33
Organigrammedusystème....................................................................34
Ilfaut suivrela procédurede soudureillustrée ci-dessouslorsque l’on
connecte des fils sous le capot. Le non-respect de cette procédure
pourraitentraînerunmauvaisfonctionnementdusystèmededémarrage
àdistance.

20
PIÈCES REQUISES
Pièce numéro 82208859
5 AMP 1X 15 AMP 4X
WARNING: / AVERTISSEMENT
This vehicle is equipped with a remote controlled engine starter.
To reduce the risk of serious Injury or death, switch engine starter
system into service mode and disconnect the vehicle battery
before performing any service on the vehicle.
Ce véhicule est doté d'un démarreur à distance. Pour réduire les
risques de blessures graves ou mortelles, mettre le démarreur à
distance en mode service et débrancher la batterie du véhicule
avant d'effectuer des travaux d'entretien sur celui-ci.
Owner's Manual
VehicleRemote Start System
TM
FeaturingPowerCodeTechnology
FortheUltimate inComfort,Convenience andSecurity
TM
®
1024256 12/03
Remote Control
CarStarterSystem
Remote Start
Activation
2X
Remote Start
Shutdown
2 sec.
2X 4X 10X
2X
Pièce numéro 82208994
OUTILS REQUIS
10mm 1/4”
RTV SEALENT
VEHICLEPREPARATION
1. Baissez une ou plusieurs des vitres des passagers de manière à ce que les
clésne puissent pasrester enfermées àl’intérieur du véhicule.
2. Débranchez et isolez le fil négatif de la batterie. La batterie devra être
rebranchéeavantlaprogrammation.
3. Levéhiculenécessite2cléscodéesSentryKeyvalidesaumomentdel’installation.
2X(françaisetanglais)