morse 82A-GT Series Operator's manual

Hand Crank
Geared Drum
Tilt. Shown with
recommended
MORStop Tilt-Brake
option.
V-Shaped
Counterweighted
Base enables
Palletizing Drum
Drum Movers and Palletizers with Geared Drum Tilt
The Specialist In Drum Handling Equipment
82A-GT Series
Drum Palletizers with Geared Tilt
MADE
IN
USA
Copyright 2020 - Morse Mfg. Co., Inc. Spec Sheet F82A (Updated 21 Apr, 2020) 1
Models with AC, DC or Air Power Drum Lift
Capacity: 600 Lb. (272 kg)
Model # 82A-GT-125
Model # 82A-GT
Overall width: 48.5” (123.2 cm), Overall length: 43” (109.2 cm)•
Turning radius: 53” (135 cm)•
Legs are 9” (22.9 cm) high and reach 20.75” (52.7 cm) in front of upright stanchion•
(2) 4” (10.2 cm) swivel casters at back•
(2) 6” (15.2 cm) wheels at front•
Horizontal 55-gallon drum reaches 18.5” (47 cm) beyond the front wheels of the•
V-shaped base
Reach onto pallet up to 20” (50.8 cm) high•
Liftupright55-gallondrumupto20”(50.8cm)fromoor.Heavydutyhydrauliclift•
cylindersincludeavelocityfusetoprovideafulllineshut-o󰀨intheeventofaline
failure.
Maximum dispensing height: 26” (66 cm) for horizontal drum•
Capacity: 600 Lb. (272 kg)•
Dimensions
Straddle a pallet up
to 41” (104 cm) wide
and 7” (17.8 cm) tall
Drum movers to palletize and dispense drum with
geared drum tilt control
This innovative design combines a V-shaped base to serve the corner of a
pallet, with geared tilt control to dispense a drum.
Model # 82A-GT
Move a drum onto
ando󰀨apallet
Models with
Powered
Drum Lift
[email protected] 103 Kuhn Rd.
Syracuse, NY, 13208 USA
morsedrum.com [phone]

The Specialist In Drum Handling Equipment
82A-GT Series
Drum Palletizers with Geared Tilt
morsedrum.com
Copyright 2020 - Morse Mfg. Co., Inc. Spec Sheet F82A (Updated 21 Apr, 2020) 2
MADE
IN
USA
Kit # 4560-P
Top Rim Clamp
to handle a 55-gallon
(210 liter) rimmed
plasticorberdrum.It
grips the upper rim of
your drum to prevent it
from slipping through
the drum holder. To
handle a 55-gallon
plastic drum with top
rim, you must install
either the Bracket
Assembly or the Top
Rim Clamp.
Kit # 4556-P
Bracket Assembly
is required to handle a
rimless plastic drum,
and recommended to
more securely handle a
berdrum.Itprovides
a brace at top and
bottom of your drum to
prevent it from slipping
length-ways through
the drum holder. It
adjusts for a 31” to
39” (78.7 to 99 cm) tall
drum.
Diameter Adaptors
Install the correct size
Diameter Adaptors to
handle each smaller
drum. They install
easily inside the
drum holder without
tools, and are quickly
removed.
Diameter Adaptors for
19” (48.3 cm) diameter
or larger drum can be
used in combination
with the Bracket Assembly. Diameter Adaptors for 17.5”
(44.5 cm) diameter or smaller have integrated brackets
at top and bottom of the drum that adjust for a drum up
to 38” (96.5 cm) tall.
Options to Handle Various Drums
Model #
55/30-17.5
Kit # 4560-P Kit # 4556-P
Recommended MORStop Tilt-Brake
Add factory installed Option # 3900i-P MORStop Tilt-Brake to
automatically lock and hold the drum tilt angle, until you turn the hand crank
again... even if drum contents shift.
The 82A-GT Series are designed to handle a ribbed 55-gallon (210 liter) steel drum. They also accept the options below for
handling other types and sizes of drum.
Optional Kit to
Move Upright Drums Only
Install kit # 4724-P to permanently convert
82A-GT Series to an 82H Drum Palletizer
for moving and palletizing an upright drum only.
It grips the upper drum rim with jaws, while
bracing the side, and has no tilt function.
Optional Kit with Jaws
Model 82A-GT-125 shown with
Kit # 4556-P Bracket Assembly•
Factory installed Option # 3900i-P•
MORStop Tilt-Brake
Model 82A-GT-125 shown with
Kit # 4560-P Top Rim Clamp•
Factory installed Option # 3900i-P•
MORStop Tilt-Brake Model 82A-GT-125 shown with
Diameter Adaptor Model # 55/30-17.5
factory installed Option # 3900i-P MORStop
Tilt-Brake

The Specialist In Drum Handling Equipment
82A-GT Series
Drum Palletizers with Geared Tilt
morsedrum.com
Copyright 2020 - Morse Mfg. Co., Inc. Spec Sheet F82A (Updated 21 Apr, 2020) 3
MADE
IN
USA
Roll the Drum Palletizer to your1.
drum with drum holder open and
positioned to engage between the
drum ribs.
Tighten the Top Rim Clamp or adjust2.
the Bracket Assembly height, if your
drum palletizer is so equipped.
Secure your drum in3.
the drum holder: Drape
the cinch chain with
exiblechaincover
across the front of the
drum, insert one chain
link into the slot on the
ratchet handle, and
turn the ratchet handle
clockwise to tighten the
cinch chain around the
drum.
Liftyourdrumfromtheooror4.
from a pallet to pouring height by
operating the powered lift control
or the hand pump.
Turn the hand crank to rotate your5.
drum into dispensing position. We recommend
the MORStop Tilt-Brake Option to automatically
hold the tilt angle, unitl you turn the hand crank
again.
Return your drum to upright position and lower6.
ittotheoororontoapallet.
To remove your drum, release the ratchet7.
handle and open the drum holder.
Move onto next drum.8.
Steps For Use of Morse Drum Palletizers / Movers / Pourers

The Specialist In Drum Handling Equipment
82A-GT Series
Drum Palletizers with Geared Tilt
morsedrum.com
Copyright 2020 - Morse Mfg. Co., Inc. Spec Sheet F82A (Updated 21 Apr, 2020) 4
MADE
IN
USA
Model # Drum Palletizer / Pourer Description Motor Domestic
Ship Wt *
Options Accepted
MORStop
Tilt-Brake
Top Rim
Clamp
Bracket
Assembly
Diameter
Adaptors
Kit to Convert
to 82H
82A-GT Hand Crank Geared Tilt - 534 Lb. (242 kg) 3900i-P 4560-P 4556-P 55/30 Series 4724-P
82A-GT-120 Hand Crank Geared Tilt, AC Power Lift 1PH/115V/60Hz, TEFC 555 Lb. (252 kg) 3900i-P 4560-P 4556-P 55/30 Series 4724-P
82A-GT-124 Hand Crank Geared Tilt, Air Power Lift - 525 Lb. (239 kg) 3900i-P 4560-P 4556-P 55/30 Series 4724-P
82A-GT-125 Hand Crank Geared Tilt, DC Power Lift 12V DC Motor ** 581 Lb. (264 kg) 3900i-P 4560-P 4556-P 55/30 Series 4724-P
82AM-GT Hand Crank Geared Tilt with spark
resistant parts - 540 Lb. (242 kg) 3900i-P 4560M-P 4556M-P 55/30M Series 4724M-P
82AM-GT-124 Hand Crank Geared Tilt, Air Power Lift
with spark resistant parts - 525 Lb. (239 kg) 3900i-P 4560M-P 4556M-P 55/30M Series 4724M-P
* Domestic Ship Dimensions: L50” W50” H56” (127 x 127 x 142 cm)
** 12V DC Power Lift includes battery, and 100/220V 50/60Hz AC charger.
Hand Pump Lift Control
Model 82A-GT
It takes 27 pumps of the
hand pump to lift a drum
to maximum height.
Ergonomic Power Lift Models
Electric Power Lift Control
Model 82A-GT-120
Use switch to raise the drum.
Lower the drum with manual
release valve.
Air Power Lift Control
Model 82A-GT-124
Useon/o󰀨valvetoraise
and lower the drum.
Battery Power Lift Control
Model 82A-GT-125
Self contained battery power-lift.
Use valve to raise and lower the
drum. 12V deep cycle battery and
separate charger are included.
Manual Lift Model
Manual Lift
Model # 82A-GT
AC Power Lift
Model # 82A-GT-120
Air Power Lift
Model # 82A-GT-124
Battery Power Lift
Model # 82A-GT-125
NOTE: 12V Deep Cycle Lead Acid Battery is designed for domestic shipment only. For export shipment, choose the following battery option:
Option “NB” No Battery. Customer must obtain battery before use... Exide # 27MDP 12V Deep Cycle Battery or equivalent.•