Motion CM-12 User manual

MANUAL CM-12
Hand-held remote 5 channel
English

CM-12 is a hand-held remote with 5 channels for operating
and programming blinds at the push of a button. Blinds can
be moved to any desired position or to a preset favourite
position. The wall mounting clip for this remote control is
included by default.
Safety
WARNING: Important safety instructions. Follow all instructions,
since incorrect installation can lead to severe injury.
Do not let children play with the blind and/or remote control.
Take care that the blind can move freely and is not blocked by
any objects.
Do not paint the device.
Keep the device dry.
Do not drop, knock, or shake the device. Rough handling can
break internal circuit boards.
Do not ingest battery, Chemical Burn Hazard" or equivalent
wording
This product contains a coin / button cell battery. If the coin /
button cell battery is swallowed, it can cause severe internal
burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.If the battery
compartment does not close securely, stop using the product
and keep it away from children. If you think batteries might
have been swallowed or placed inside any part of the body,
seek immediate medical attention.
Replacement of a battery with an incorrect type that can defeat
a safeguard.
Disposal of a battery into fire or a hot oven, or mechanically
crushing or cutting of a battery, that can result in an explosion.
Leaving a battery in an extremely high temperature
surrounding environment that can result in an explosion or the
leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure that may
result in an explosion or the leakage of flammable liquid or gas.
For the latest information and updated manuals,
visit rtube.nl/cm-12
Channels Max.
blinds
Frequency Range Frequency
emission power
Power
supply
Length Width Height Working
temperature
Certificates
5 unlimited 433.925 MHz
30 m with
1 concrete
wall
≤2.32dBm CR2430
3.0V 120 mm 45 mm 14 mm -10°C~50°C

FCC Manual I FCC ID: ZY4CM12
Regulatory Information
1 FCC Information for User
This product does not contain any user-serviceable components and is to be used
with approved antennas only. Any product changes or modifications will invalidate all
applicable regulatory certifications and approvals.
2 FCC Electronic Emission Notices
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may
cause undesired operation.
3 FCC Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated
in a commercial environment. This equipment generates, uses and can radiate radio-
frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications.
Operation of this equipment in a residential area may cause harmful interference, in
which case the user will be required to correct the interference at their own expense.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna
Increase the distance separating the equipment and receiver
Connect the equipment to an outlet on a circuit different from that to which the
receiver is connected
Consult the dealer or an experienced radio/TV technician for help
Cleaning
Follow these general rules when cleaning the outside of the
device and its components:
Use a damp, soft, lint-free cloth. Avoid getting moisture in
openings.
Do not use aerosol sprays, solvents, alcohol, or abrasives.
Service & Support
Do not perform repairs yourself. Do not attempt to open the
device or disassemble it. You run the risk of electric shock and
voiding the limited warranty. No user-serviceable parts are inside.
Warranty Service
First follow the advice in this manual. If the product appears to be
damaged or does not function properly, go to your local dealer for
instructions on how to obtain warranty service.
Recycle
This marking indicates that this product should not be
disposed with other household wastes throughout the EU.
To prevent possible harm to the environment or human
health from uncontrolled waste disposal, recycle it responsibly to
promote the sustainable reuse of material resources. To return
your used device, please use the return and collec-tion systems or
contact the retailer where the product was purchased. They can take
this product for environmental safe recycling.
EU Declaration
Hereby, Coulisse declares that the radio equipment type CM-12
is in compliance whith directive 2014/53/EU. The full text of the
EU declaration of conformity is available at the following internet
address: www.my.coulisse.com

1
1. BUTTONS
Buttons
Up
Right
Down
Channel
Selection
Left
Centre
(stop/favourite)
Pair
button
The center button has two functions: press to stop the blind,
hold to move the blind to its favorite position.
Channel
indicator

+
-
2 3
CR2430 3,0V
Changing the battery When the channel indicator is flashing at a high frequency,
the battery needs to be replaced. Remote holder Different materials require different types of fittings. Always choose screws and plugs that are specially suited
to the material.
3. REMOTE HOLDER2. CHANGING THE BATTERY

44.1
4.2
4.3
Pair a remote Repeat steps 4.1 - 4.3 to remove a blind from a channel.
4. PAIR A REMOTE4. PAIR A REMOTE
Shortly press the program button on the motor. The
blind will start stepping, indicating that program mode
has been activated.
(The blind keeps stepping until the program mode is
deactivated)
Press the pair button on the back of the remote
control to pair the blind with the selected channel.
The blind will shortly stop stepping, indicating that
the remote has been paired with the blind.
Select a desired channel for the blind using the channel
selection button on the remote control.
Pair
button
Channel indicator
Channel Selection

1
1
5
5.1 5.2 5.3 5.4 5.5
Single select makes it possible to activate program mode on
a single blind through a remote control, without having to
physically press the program button on the blind.
Single select 5 channel remote
+
The remote
starts searching
for blinds (search
mode). This is
indicated by the
LEDs flashing
from left to right.
To activate
Single select,
simultaneously
hold the centre
button and press
the pair button.
Once a blind is found,
the channel LED will
flash and the blind
starts stepping,
indicating that program
mode has been
activated. The blind
can now be (un)paired
with the remote and/or
programmed.
To exit Single select,
press the right button
during search mode.
5. SINGLE SELECT 5 CHANNEL REMOTE5. SINGLE SELECT 5 CHANNEL REMOTE
To search for the next
blind, press the right
button. Search mode will
be activated.
To find the previous blind,
press the left button.

6
6.1 6.2 6.3 6.4 6.5
Channel select makes it possible to copy blinds in between
channels/remotes without having to physically press the
program button on the motors.
Select the
channel from
which the
blinds must
be copied.
To activate channel
select, simultaneously
hold the channel
selection button and
press the pair button.
6. CHANNEL SELECT 5 CHANNEL REMOTE6. CHANNEL SELECT 5 CHANNEL REMOTE
+
All blinds in the selected
channel will start stepping,
indicating program mode has
been activated. All blinds can be
copied to a new channel on the
same remote or other remote.
Select a new channel on the
(new) remote.
Press the pair button
on the (new) remote to
pair the blinds with the
new channel.
To exit channel select,
go back to the channel
selected at step 6.1
and repeat step 6.2
Channel select 5 channel remote

motion-blinds.com
CM12U-R3
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted, in any form, by any means, electronic, mechanical, photocopying,
recording, digital or otherwise without the written permission of the publisher.
Although this manual has been composed with the utmost care, Coulisse b.v. does not
accept any responsibility for damage due to mistakes and/or faults in this manual.
Coulisse b.v. reserves the right to revise the manual and to revise and/or change its
content at any time, without obligation to notify any person or entity of such revisions
or changes.