Motion CM-15 User manual

MANUAL
CM-15
Wall remote 1 channel
English

CM-15 is a wall remote with 1 channel for operating and programming
blinds at the push of a button. Blinds can be moved to any desired position
or to a preset favourite position. The remote control can be used separately
from the wall plate as as a hand-held remote separately.
Channels Max.
blinds
Frequency Range Power
supply
Length Width Height Certificates
15 Unlimited 433 MHz
30 m with
1 concrete
wall
CR2430
3.0V 120 mm 45 mm 14 mm
For the latest information and updated manuals,
visit rtube.nl/cm-15

Safety
WARNING: Important safety instructions.
Follow all instructions, since incorrect
installation can lead to severe injury.
Do not let children play with the blind
and/or remote control.
Take care that the blind can move
freely and is not blocked by any objects.
Do not paint the device.
Keep the device dry.
Do not drop, knock, or shake the device.
Rough handling can break internal
circuit boards.
Cleaning
Follow these general rules when
cleaning the outside of the device and its
components:
Use a damp, soft, lint-free cloth. Avoid
getting moisture in openings.
Do not use aerosol sprays, solvents,
alcohol, or abrasives.

Service & Support
Do not perform repairs yourself. Do
not attempt to open the device or
disassemble it. You run the risk of electric
shock and voiding the limited warranty.
No user-serviceable parts are inside.
Warranty Service
First follow the advice in this manual. If
the product appears to be damaged or
does not function properly, go to your
local dealer for instructions on how to
obtain warranty service.

FCC Manual I FCC ID: ZY4CM15
Regulatory Information
1 FCC Information for User
This product does not contain any user-serviceable
components and is to be used with approved antennas
only. Any product changes or modifications will
invalidate all applicable regulatory certifications and
approvals.
2 FCC Electronic Emission Notices
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received,
including interference that may cause undesired
operation.
3 FCC Radio Frequency Interference
Statement
This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses and can radiate radio-frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area may
cause harmful interference, in which case the user will
be required to correct the interference at their own
expense.
If this equipment does cause harmful interference to
radio or television reception, which can be determined

by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna
Increase the distance separating the equipment and
receiver
Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV
technician for help

1Buttons The center button has two functions:
press to stop the blind, hold to move
the blind to its favorite position.
1. BUTTONS
Up
Right
Down
Left
Centre
(stop/favourite)
Indicator
Pair
button

2Activate the remote
2. ACTIVATE THE REMOTE

+
-
CR2430 3,0V
1
3Changing the battery When the indicator is flashing at a high
frequency, the battery needs to be
replaced.
3. CHANGING THE BATTERY

Click!
23
3. CHANGING THE BATTERY
Click!

4Remote holder
4. REMOTE HOLDER
PICO-WBX-ADAPT
(ABC-27) Claro wallplate
(ABC-27)

Different materials require
different types of fittings.
Always choose screws
and plugs that are specially
suited to the material.
4. REMOTE HOLDER
Claro wallplate
(ABC-27)

5Pair a remote Repeat steps 5.1 - 5.2 to remove a blind
from a channel.
5. PAIR A REMOTE

5.1
5.2
5. PAIR A REMOTE
Shortly press the program button on the motor. The
blind will start stepping, indicating that program mode
has been activated.
(The blind keeps stepping until the program mode is
deactivated)
Press the pair button on the back of the remote control
to pair the blind with the remote control.
The blind will shortly stop stepping, indicating that the
remote has been paired with the blind. Pair
button

of this publication may be reproduced, stored in a retrieval system, or transmitted, in any
form, by any means, electronic, mechanical, photocopying, recording, digital or otherwise
without the written permission of the publisher.
Although this manual has been composed with the utmost care, Coulisse b.v. does not
accept any responsibility for damage due to mistakes and/or faults in this manual.
Coulisse b.v. reserves the right to revise the manual and to revise and/or change its
content at any time, without obligation to notify any person or entity of such revisions
or changes.

HANDBUCH
CM-15
Wandfernbedienung 1 Kanal
Deutsch

CM-15 ist eine Wandfernbedienung mit 1 Kanal zur Steuerung und
Programmierung von Rollos durch Knopfdruck. Rollos können in
jede gewünschte Position oder eine voreingestellte Lieblingsposition
versetzt werden. Die Fernbedienung kann separat vom Wandhalter als
Handfernbedienung verwendet werden.
Kanäle Max.
Rollos
Frequenz Bereich Stromquelle Länge Breite Höhe Zertifikate
1unbe-
grenzt 433 MHz
30 m mit
1 konkreten
Wand
CR2430 3,0V 66 mm 32,5 mm 13,8 mm
Für mehr Informationen und aktualisiert
Bedienungsanleitungen besuchen Sie bitte
rtube.nl/cm-15

Sicherheit
WARNUNG: Wichtige Sicherheitshinweise
Befolgen Sie sämtliche Hinweise, da
eine fehlerhafte Installation zu ernsten
Verletzungen führen kann.
Lassen Sie Kinder nicht mit dem Rollo
und/oder der Fernbedienung spielen.
Achten Sie darauf, dass das Rollo sich
frei bewegen kann und nicht durch
Objekte blockiert wird.
Streichen Sie das Gerät nicht über.
Halten Sie das Gerät trocken.
Lassen Sie das Gerät nicht fallen.
Schlagen Sie nicht darauf und
schütteln Sie es nicht. Durch groben
Umgang können interne Leiterplatten
beschädigt werden.
Reinigung
Befolgen Sie bei der Reinigung des Geräts
und der einzelnen Komponenten diese
allgemeinen Regeln:
Verwenden Sie ein feuchtes, weiches
und fusselfreies Tuch. Achten Sie
darauf, dass keine Feuchtigkeit in
Öffnungen eindringt.
Verwenden Sie keine Sprays,
Lösungsmittel, Alkohol oder
Scheuermittel.