Motion CM-18 User manual

MANUAL CM-18
Pull remote 1 channel
English

For the latest information and updated manuals,
visit rtube.nl/cm-18
CM-18 is a pull remote with 1 channel for operating single blinds or
shading networks with a simple pull. Blinds can be moved to any desired
position. Pull once to move the blinds to the end positions, pull again to
stop the blinds. Operating remotely controlled blinds has never been so
easy and intuitive: anyone can do it.
Channels Max.
blinds
Frequency Range Power
supply
Length Width Height Certificates
1 Unlimited 433 MHz 20 m open
space
2 x LR44
1.5V 19.5 mm ø 69.9 mm

Safety
WARNING: Important safety instructions.
Follow all instructions, since incorrect
installation can lead to severe injury.
Do not let children play with the blind
and/or remote control.
Take care that the blind can move
freely and is not blocked by any objects.
Do not paint the device.
Keep the device dry.
Do not drop, knock, or shake the device.
Rough handling can break internal
circuit boards.
Cleaning
Follow these general rules when
cleaning the outside of the device and its
components:
Use a damp, soft, lint-free cloth. Avoid
getting moisture in openings.
Do not use aerosol sprays, solvents,
alcohol, or abrasives.

Service & Support
Do not perform repairs yourself. Do
not attempt to open the device or
disassemble it. You run the risk of electric
shock and voiding the limited warranty.
No user-serviceable parts are inside.
Warranty Service
First follow the advice in this manual. If
the product appears to be damaged or
does not function properly, go to your
local dealer for instructions on how to
obtain warranty service.

FCC Manual I FCC ID: ZY4CM18
Regulatory Information
1 FCC Information for User
This product does not contain any user-serviceable
components and is to be used with approved antennas
only. Any product changes or modifications will
invalidate all applicable regulatory certifications and
approvals.
2 FCC Electronic Emission Notices
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received,
including interference that may cause undesired
operation.
3 FCC Radio Frequency Interference
Statement
This equipment has been tested and found to comply
with the limits for a class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful
interference when the equipment is operated in a
commercial environment. This equipment generates,
uses and can radiate radio-frequency energy and,
if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area may
cause harmful interference, in which case the user will
be required to correct the interference at their own
expense.
If this equipment does cause harmful interference to
radio or television reception, which can be determined

by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna
Increase the distance separating the equipment and
receiver
Connect the equipment to an outlet on a circuit
different from that to which the receiver is connected
Consult the dealer or an experienced radio/TV
technician for help

1Buttons
1. BUTTONS
Pair
Button

2
+
-
LR44 1.5V
1
2
2. CHANGING THE BATTERY
Changing the battery

3Pair a remote Repeat steps 3.1 - 3.2 to remove a blind
from a channel.
3. PAIR A REMOTE

3.1
3.2
3. PAIR A REMOTE
Shortly press the program button on the motor. The
blind will start stepping, indicating that program mode
has been activated.
(The blind remains stepping until the program mode is
de-activated.)
Press the pair button on the remote control to pair the
blind to the remote control. The blind will shortly stop
stepping indicating that the remote has been paired to
the blind.
Pair
button

4
1
2
3
4. CONNECT A CHAIN
Connect a chain

45
4. CONNECT A CHAIN

5
5. ATTACH TO A BLIND
Attach to a blind Roller blind bracket
RCU-21

5. ATTACH TO A BLIND
Roller blind cassette
drill a ø 5 mm hole

5. ATTACH TO A BLIND
Roman blind
drill a ø 5 mm hole

5. ATTACH TO A BLIND
Venetian blind
drill a ø 5 mm hole

6
6.1
6. CONTROL
Control After the blind has reached its end position, the
consecutive ”STOP”command is eliminated after
60 seconds. The next pull will directly operate the blind.
Pull once to move the
blind to its end position.

6.2 6.3
6. CONTROL
Pull again to stop the
blind.
Pull again to move the blind
in the opposite direction.

All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted, in any form, by any means, electronic, mechanical, photocopying,
recording, digital or otherwise without the written permission of the publisher.
Although this manual has been composed with the utmost care, Coulisse b.v. does not
accept any responsibility for damage due to mistakes and/or faults in this manual.
Coulisse b.v. reserves the right to revise the manual and to revise and/or change its
content at any time, without obligation to notify any person or entity of such revisions
or changes.