Motocaddy M1 Lite User manual

EN
M-Series Electric Trolley
Instruction Manual
Distance Measurement Device (DMD) features are legal to use when local USGA and R&A
rule 14-3 is in effect. Always check local and competition rules prior to commencing play
REGISTERONLINE
www.motocaddy.com/warranty
Visit www.motocaddy.com/instructions for other Motocaddy instructions including translations

Page 2
Contents
Locating your Serial Number / Information about DHC.......3
Safe use of your Trolley / Caring for your Trolley .................4
Caring for your Trolley / Battery Care and Advice................5
Charging Instructions / Caring for your Lithium Battery.......6
Caring for your Lithium Battery ............................................7
Attaching the Wheels ...........................................................8
Adjusting the Front Wheel Alignment..................................9
Unfolding your Trolley ........................................................10
Folding your Trolley............................................................11
Using the Upper and Lower Bag Supports.........................12
Adjusting the Bag Supports ...............................................13
M1 - Equipment Overview .................................................14
M1 - Using your trolley / Power and Battery Level.............15
M3 PRO - Equipment Overview .........................................16
M3 PRO - Digital Control Panel / Digital Functions ...........17
M3 PRO - Starting, Stopping & Speed / USB Charging.....18
M3 PRO - Setting the Time / Using the Round Timer ........19
M3 PRO - Using Adjustable Distance Control....................20
M3 PRO - Distance Readouts .............................................21
M3 PRO - Using the Competition Mode............................22
M3 PRO - Setting the Security Pin Code............................23
M3 PRO - Changing / Disabling the Security Pin Code.......24
M5 CONNECT - Equipment Overview...............................25
M5 CONNECT - Digital Control Panel / Digital Functions...26
M5 CONNECT - Power & Battery Level / USB Charging......27
M5 CONNECT - Using Adjustable Distance Control .........28
M5 CONNECT - Smart Features Overview ........................29
Downhill Control and Parking Brake (DHC models)...........30
Declaration of Conformity ..................................................31

Page 3
Locating your Serial Number / Information about DHC
Locating your Serial Number
The serial number for your M-Series trolley is located on the trolley underside next to the motor (g. 1).
This number is required when registering your warranty online and should be kept handy for future use.
The same number should also be on the box received with your trolley. Please ensure you keep hold of
the packaging in case you need to return your trolley for any reason. A proof of purchase must also be
kept in case your trolley requires servicing during its warranty period.
Please keep a record of your trolley serial number here for future reference
MCM
Information about DHC (Downhill Control) models
The information in this instruction manual applies to both standard and DHC electric trolley models. For DHC specic
functionality, please turn to pg 30.
Fig 1

Page 4Page 4
Safety Cut-out / Safe Use of your Trolley / Caring for your Trolley
Safety Cut-out
This Motocaddy M-Series trolley is tted with a timed safety cut-out feature. Once started the trolley will automatically cut power
to the motor after ten minutes to prevent any possible damage to the trolley. Pressing the on/off button will restart the trolley.
Safe Use of your Trolley
This Motocaddy trolley is designed for the transportation of golf bags and clubs contained within. Using the trolley for any
other pupose may cause damage to the trolley and cause harm to the user.
• Do not attempt to transport any other equipment
• The trolley is not designed for the transportation of people
• Do not use the trolley to assist you when going up hills
• Submerging the trolley in water (e.g. a lake) is likely to cause damage to the trolley
• Do not operate the trolley whilst under the inuence of drugs or excessive amounts of alcohol
• All batteries must be disconnected from the trolley before transporting
Caring for your Trolley
Although your Motocaddy trolley has been weatherproofed, please follow these simple guidelines to help protect your trolley:
• Do not store your trolley outside
• Try to minimise exposure to rain as much as possible with an umbrella during heavy rainfall
• Wipe excess water from the trolley prior to storage
• Never use a pressure washer to clean your trolley. To prevent water damage, wipe down with a damp cloth
• Avoid using high pressure air hoses near moving components

Page 5
Caring for your Trolley / Battery Care and Advice
This Motocaddy trolley is designed to require very little maintenance. We do however recommend giving your trolley regular
checks to ensure:
• There is no build up of excess mud and dirt
• The front wheel nut is on tightly and quick release lever is clamped down
• The front wheel is not clogged up and turns freely
Only original Motocaddy parts should be used when repairing your trolley.
Battery Care and Advice
All batteries must be charged as soon as possible after each use. Leaving batteries discharged for long periods of time will
affect the battery life.
Please ensure that only batteries supplied by Motocaddy are charged with Motocaddy chargers. Cyclic battery chargers are
designed specically in accordance with the battery manufacturer’s requirements. The Lithium battery charger MUST NOT be
used to charge any other battery and is designed for use with Motocaddy Lithium batteries only.
The charger should only be connected to an earthed socket outlet; the battery charger should only be opened and maintained
by authorised personnel. Unauthorised opening will invalidate your warranty.
The battery must be stored and charged on a dry non-carpeted surface and charged at temperatures ranging between 10°C
and 30°C. Charging above or below these temperatures is not recommended as it can reduce the battery capacity.
When connecting your battery to the trolley, please ensure that the connections match up black to black and grey to grey.

Page 6
Charging your Lithium Battery / Caring for your Lithium Battery
Charging your Lithium Battery
1. Unplug the Lithium battery from the trolley. This should always be performed before folding the trolley to avoid damage
to the battery and/or trolley
2. Plug the charger into your mains supply
3. Attach the battery cable to the charger matching the black and grey connections
4. When the charging LED indicator has turned green, the battery is fully charged and ready to be used
RED - Battery charging GREEN - Battery fully charged and ready to be disconnected
5. The charging process will take between 3 to 5 hours depending on the depth of discharge
(please be aware that this may take longer for the rst few charges)
6. Once charging is complete please disconnect the charger from the mains power supply
7. Finally disconnect the charger from the battery
Caring for your Lithium Battery
• Try to avoid getting the battery too wet (i.e. do not submerge the battery, avoid deep puddles and do not clean
your trolley whilst the battery is still in the battery tray)
• Dropping the battery may cause damage to the internal cells
• Do not lift or carry the battery by the cable
• Use a damp cloth to clean off any dirt

Page 7
Caring for your Lithium Battery
Recommendations for the Hibernation of Lithium batteries During Winter Months
If for any reason your Lithium battery is not going to be used for lengthy periods, e.g. 3 months over the winter, it is advised to
store the battery half charged. To do this simply use the battery for a round of golf as usual and charge it for 1.5 hours at the
end of the round. Before the battery is used again, recharge it (top it up) prior to use. We recognise that extended absences
are not always planned in advance, however when it is likely that you will not be using your battery for a period of time it
is good practice to follow these steps to extend the life of your Lithium battery. Please ensure that the charger is ALWAYS
disconnected from the battery after charging.
Battery Management System (BMS)
Motocaddy Lithium batteries are tted with a comprehensive battery management system (BMS) to protect the battery from
excessive abuse, high currents, deep discharge and overcharge. When the battery is delivered there may be no output as the
BMS is designed to maximize safety whilst shipping. Please ensure that the battery is fully charged prior to connecting it to
your trolley as this will activate the BMS and effectively ‘switch-on’ the battery. From time to time, at deep discharge or long
term storage the BMS may switch-off the battery. A full battery charge will rectify this problem.
Motocaddy golf trolleys are designed to work with the BMS system installed in the Lithium batteries and the voltage meter
is also synchronised to work in conjunction with the battery. If for any reason the voltage on the battery falls below the low
battery warning on the trolley, then the BMS may disable the battery to protect it. Again if this occurs please recharge fully.
Please be aware that Lithium batteries tend to ‘drop off’ quickly at the end of the cycle so it is not advisable to attempt to play
excessive holes as the BMS will activate for protection purposes.

Page 8
Attaching the Wheels
Attaching the Wheels
There is a left and a right wheel and it is important that you put them on the correct
side, otherwise the trolley will not move. There is an “L” and “R” on the inside of the
wheel on the central hub. Left and Right sides are determined when stood behind the
trolley at the handle.
NB : DHC trolley models do not have a specic left and right wheel.
To attach the wheels follow these simple steps:
1. Push the quick release button in towards the centre of the wheel
2. Slide the wheel on as far as it will go (onto the inner groove)
3. Once in place, release the button and pull the wheel outwards slightly to lock in place
4. A small click will conrm they are in the correct position
The outer groove can be used as a “free-wheel” option if you run out of battery power.
IMPORTANT : To check you have attached the wheels correctly onto the inner groove,
you will nd they only rotate freely in one direction (not applicable to DHC models).
Inverting the Wheels
The wheels can be inverted to reduce the trolley width for transportation and storage.
1. Push and hold the quick release button while sliding the wheel off the axle
2. Flip the wheel over, push and hold the button, then slide onto the axle as far as possible
3. Release the button and pull wheel out slightly until it engages with the free wheel groove
Left
Right

Page 9
Adjusting the Front Wheel Alignment
Adjusting the Front Wheel Alignment
In the unlikely event that your trolley is not tracking in a straight line, the alignment of the front wheel
can be adjusted to rectify the fault. This problem can be caused by a number of factors including a
slightly loose bag support or an unevenly packed golf bag. Should you wish to alter the alignment of
the front wheel, follow these simple steps:
1. Lift the quick release lever positioned on the front wheel
housing and loosen the wheel nut (g. 1)
2. There are two small metal dials on either side of the housing
that are used to realign the wheel (g. 2)
3. If your trolley is veering to the right, you will need to turn the left
hand dial clockwise and the right hand dial anti-clockwise
4. If your trolley is veering to the left, you will need to turn the right
hand dial clockwise and the left hand dial anti-clockwise
5. Tighten the wheel nut and push down the lever to lock the wheel
back into place (g. 3)
This procedure can be carried out until you are happy the trolley is moving in a straight line
(please note you may only need to adjust one dial at a time).
NB : These instructions are based on positioning yourself in front of the trolley looking at the wheel.
Fig 2
Fig 3
Fig 1

Page 10
Unfolding your Trolley
Unfolding your Trolley
We recommend unfolding your trolley once the wheels have been un-inverted and reattached (see pg 8).
1. Lift the upper bag support slightly and release the upper latch (g. 1)
2. Unfold the handle and re-secure the latch (g. 2)
3. Release the lower latch (g. 3)
4. Lift the trolley handle up into position (g. 4). The front wheel will automatically unfold
5. Re-secure the lower latch and ensure the auto-open stand is folded away (g. 5)
Fig 1 Fig 2 Fig 3 Fig 4 Fig 5

Page 11
Fig 1 Fig 2 Fig 3 Fig 4 Fig 5
Folding your Trolley
1. Release the lower latch (g. 1). The auto-open stand will also be activated
2. Fold the frame forward until fully extended (g. 2). The front wheel will automatically fold underneath
3. Release the upper latch and fold the handle back until the trolley is fully folded (g. 3)
4. Re-secure both latches. If you wish to stand the trolley upright, leave auto-open stand out. Remember to ensure
the auto-open stand is pushed down if not being used (g. 4)
5. The wheels can be inverted to reduce the trolley width for transportation and storage (g. 5). See pg 8 for details
NB : Please ensure the auto-open stand is folded away when not in use to prevent damage.
Folding your Trolley

Page 12
Using the Upper and Lower Bag Supports
Fig 3
Fig 2
Fig 1
Using the Upper Bag Supports
The upper bag support straps are secured using the following steps:
1. Stretch the elasticated strap around the bag & loop the rounded bar underneath the hook (g. 1)
2. Position the two placement straps centrally on your golf bag (g. 2)
Using the Lower Bag Supports
This Motocaddy trolley is tted with the EASILOCK™ bag attachment system.
If you are using an EASILOCK™ compatible golf bag please follow these simple instructions:
1. Remove the two pre-tted lower bag straps by depressing the rear button and sliding (g. 3)
2. Match up the indicating line on the golf bag with the line on the lower bag support
3. Lower the bag until the pins lock in position. You should hear a small click
If you are using a non-EASILOCK™ golf bag, please use the following instructions:
1. Stretch the lower bag strap around the bag base & loop the rounded bar underneath the hook
2. Position the two placement straps centrally on the base of your golf bag
Please ensure all straps are hooked securely before releasing. Failure to do so could result in injury.

Page 13
Adjusting the Bag Supports
Fig 3
Fig 2
Fig 1
Adjusting the Bag Supports
The bag support straps are manufactured from elasticated material to allow your golf bag to be
held tightly in place.
The strap should be adjusted to be reasonably tight around the golf bag:
1. Unclip the elasticated straps from the housing by pulling outwards in the direction shown (g. 1)
2. Move the bar as required to tighten or loosen the strap tting. Pulling the bar downwards will
tighten, pushing it upwards will loosen (g. 2)
3. Ensure that the straps are clipped back into the housing before use (g. 3)

Page 14
M1 - Equipment Overview
1. LCD Digital Display
2. Speed Setting (see pg 15)
3. Advanced Battery Meter (see pg 15)
4. Speed Controller & On/Off Button (see pg 15)
5. Upper Bag Support
6. Upper Release Latch
7. Rear Wheels
8. Rear Wheel Release Button
9. EASILOCK™ Lower Bag Support
10. Battery
11. Battery Tray
12. Motor (under Battery Tray)
13. Front Wheel
14. Front Wheel Alignment Adjusters
15. Battery Connector
16. Auto-Open Stand
17. Lower Release Latch
M1 - Equipment Overview
1
5
6
7
9
10
12
13
8
11
14
15
16
17

Page 15
Using your M1
The M1 is very simple to control. There is one main button that is
used to start and stop the trolley, whilst also controlling the speed,
which can be adjusted while the trolley is stationary or in motion.
The trolley has 9 speed settings (1 to 9) with 1 being the slowest
and 9 the fastest. To increase the speed, rotate the speed dial
clockwise, or anti-clockwise to decrease the speed.
To start the trolley, simply select your required speed setting
and press the button. The trolley will smoothly accelerate until it
reaches the selected speed. To stop the trolley, simply press the
button again - there is no need to reduce the speed setting.
You will notice the red chevrons will start ashing when you
press the button, this indicates that the trolley has been started.
The trolley is designed to protect your battery from being fully
discharged, should your battery capacity drop too low the trolley
will cut the power to the motor. If this should happen you will
see the battery meter ashing on screen.
NB : Please be aware that certain moisture, temperature and humidity conditions can result in localised misting within
the display screen. This will not affect the trolley functionality, nor cause any damage and will return to normal when
adverse conditions subside.
Using your M1 / Power and Battery Level
2
3
4

Page 16
M3 PRO - Equipment Overview
M3 PRO - Equipment Overview
1. LCD Advanced Digital Control Panel
2. Upper Bag Support
3. Upper Release Latch
4. Rear Wheels
5. Rear Wheel Release Button
6. EASILOCK™ Lower Bag Support
7. Battery
8. Battery Tray
9. Motor (under Battery Tray)
10. Front Wheel
11. Front Wheel Alignment Adjusters
12. Battery Connector
13. USB Charging Port (under handle)
14. Auto-Open Stand
15. Lower Release Latch
1
2
3
4
6
7
9
10
5
8
11
12
13
14
15

Page 17
M3 PRO - The Advanced Digital Control Panel / Operating the Digital Functions
The Advanced Digital Control Panel
1. Speed Setting
2. Clock
3. Round Timer
4. Battery Meter
5. Distance Readings
6. Left Button
7. Speed Controller & On/Off
8. Right Button
9. USB Charging Port (under handle)
Operating the Digital Functions
To activate the control panel simply connect the battery to the
trolley. Once activated the screen will display the speed setting
the trolley will set off at when started. The lime chevrons will
ash when moving.
The trolley is designed to protect your battery from being fully
discharged; should your battery voltage drop too low the trolley
will cut the power to the motor. If this should happen you will see the battery meter ashing on screen.
NB : Please be aware that certain moisture, temperature and humidity conditions can result in localised misting within
the display screen. This will not affect the trolley functionality, nor cause any damage and will return to normal when
adverse conditions subside.
1
5
34
2
76
8
9

Page 18
M3 PRO - Starting, Stopping & Changing Speed / Using the USB Charging Port
Starting, Stopping and Changing the Speed of your Trolley
The speed can be adjusted while the trolley is stationary or in motion. Rotate the central button clockwise to increase the
speed setting and anti-clockwise to decrease. You will see the number in the centre of the screen changing accordingly.
The settings range from 1 (slowest) to 9 (fastest). To start the trolley, simply press the button. To stop it, press the button again
- there is no need to decrease the speed before stopping as it is designed to smoothly accelerate back to the required speed.
You will notice the lime chevrons will start ashing when you press the button, this indicates that the trolley has been started.
Using the USB Charging Port
The M3 PRO features a USB charging port designed to charge GPS devices during your round, should your device require a top up.
Simply remove the covering cap and plug a USB cable into the charging port located on the underside of the handle.
The device will continue charging for the duration of time that the cable is attached and the battery is connected.
It is important to note that the rate of charge will be lower than that of a mains AC charger and similar to plugging the device
into a PC. The USB charger takes power from the main trolley battery and continuous charging will reduce the battery capacity
between charges. The trolley is designed to disable the USB port when the battery capacity reaches a preset level.

Page 19
Setting the Time
1. Press and hold the right button for three seconds until the minutes start ashing
2. Set the minutes by pressing the left button, each press will increase the time by one minute
3. To toggle to the hour press the right button again
4. Set the hour in the same way as the minutes
5. Once the time is correct, press and hold the right button for three seconds to conrm
Using the Round Timer
The round timer will automatically start counting when you connect the battery to the trolley. To reset
the round timer at the start of your round, press and hold both the left and right buttons together for
1 second, you will see the round timer ash, release the buttons and the timer will be reset (g. 1).
M3 PRO - Setting the Time / Using the Round Timer
Fig 1

Page 20
M3 PRO - Adjustable Distance Control
Using the Adjustable Distance Control
1. Whilst stationary, select the speed at which you wish the trolley to start
2. Hold down the central ‘on/off’ button for 2 seconds
3. The Distance Display will change to indicate ‘05’ (5 yards or metres) and the letters ‘ADC’ will
appear under the speed setting
4. Rotate the button clockwise to increase the distance and anti-clockwise to decrease (g. 1)
5. Press the button down once to set the trolley off in motion
6. The distance will count down in increments of 1 yard/metre until the desired distance is reached.
The trolley can be stopped at any stage by pressing the central button once
In the unlikely event that your trolley fails to register distance whilst in ADC mode, the trolley will cut
power to the motor to prevent the trolley from travelling too far. The trolley screen will ash ‘dist’ to
indicate that this safety feature has been activated (g. 2).
The trolley can be reset by pressing the on/off button once, thereby allowing you to continue to use
the trolley with ADC disabled until you are able to contact our technical support team. Fig 2
Fig 1