Motocaddy M7 GPS User manual

EN
REGISTERONLINE
www.motocaddy.com/warranty
Visit www.motocaddy.com/instructions for other Motocaddy instructions including translations
Distance Measurement Device (DMD) features are legal to use when local USGA and R&A
rule 4.3 is in effect. Always check local and competition rules prior to commencing play
IMPORTANT: Scan the QR code to ensure
that your M7 GPS software remains up to
date and performance is always optimised
M7 GPS Electric Trolley
Instruction Manual
ORIGINAL VERSION

Page 2
Cellular Performance Plan
5
3
1
6
4
2
Powered by next-generation cellular data technology, the
Motocaddy Performance Plan is available through a low-cost
annual subscription package that unlocks a selection of premium
performance-enhancing features, including:
1. Full hole mapping
2. Detailed green view
3. Advanced statistic tracking
4. Performance analysis
5. Automatic course updates
6. Notication of software updates
All M7 GPS owners receive a no-obligation 12-month FREE trial.
Follow the on-screen prompts to get started.
LEARN MORE: Scan the QR code or visit
www.motocaddy.com/performance-plan

Page 3
Software Updates / Locating your Serial Number / Information about DHC
Locating your Serial Number
The serial number is located on the trolley underside next to the motors (g. 1). This number is required
when registering your warranty online and should be kept handy for future use.
The same number should also be on the box received with your trolley. Please ensure you keep hold of the
packaging in case you need to return your trolley for any reason. A proof of purchase must also be kept in
case your trolley requires servicing during its warranty period.
Fig 1
Please keep a record of your trolley serial number here for future reference:
MCM
Information about DHC (Downhill Control)
The letters DHC stand for ‘Downhill Control’ and mean that your trolley will maintain a controlled speed whilst travelling down hills.
Whenever you are looking to move the trolley in manual mode, even if just to reposition it ready to use, always put it on a low
speed setting to make it easier to steer.
IMPORTANT - Software Updates
The M7 GPS has been developed to include WiFi powered, Over-the-Air course and system updates. It is recommended
that you always use the latest rmware to take advantage of new features, bug xes and system improvements.
Join our dedicated M7 GPS mailing list by scanning the QR code or visiting www.motocaddy.com/support/m7gps.

Page 4
16
3
Equipment Overview
1
15
9
10
5
14
4
2
11
1. LCD Touchscreen Display (see page 24)
2. Manual Speed Controller & On/Off Button
3. USB Charging Port (under handle)
4. Remote Control Handset & Cradle
5. Upper Release Latch
6. Upper Bag Support
7. Battery
8. Battery Connector
9. EASILOCK™ Lower Bag Support
10. Front Wheels
11. Front Wheel Alignment Adjusters
12. Rear Wheels
13. Rear Wheel Release Button
14. Auto-Open Stand
15. Lower Release Latch
16. Motors (under Battery Tray)
17. Anti-Tip Wheel Release
18. Anti-Tip Wheel
78
6
13
12
17
18

Page 5
Remote Control Handset
1. Indicator LED
2. Plus (+) Button
3. Stop Button
4. Left (<) Button
5. Right (>) Button
6. Minus (-) Button
7. On/Off & Lock Button
8. Charging Port
The remote handset contains a rechargeable Lithium battery. The handset can
be recharged using a mini USB cable (supplied), the charging port is located under
the rubber flap at the base of the handset. Once plugged in, the handset needs to be
switched on using the 'On/Off' button to charge.
The green LED on the handset will flash whilst being charged, once it is fully charged
the green LED will be on and not flashing. This will take around 4-5 hours from empty.
When the handset battery starts to get low, the LED will flash red when pressing a
button. Should the battery go completely flat there will be no LED when pressing
a button. Should this happen, the trolley will stop. You can recharge the handset
using the USB port on the trolley.
Please be aware that charging the remote handset through the USB port will
take power from the main trolley battery and prolonged charging will reduce
the trolley battery capacity between charges.
Remote Control Handset
2
6
3
8
1
5
7
4

Page 6
Trolley Safety
Safe use of your Trolley
The rst time you use the M7 GPS, we would advise using it on an open area of grass. The trolley speeds and steering characteristics
will vary depending on the surface. The M7 GPS will turn much quicker on hard, smooth surfaces and will behave differently on grass.
You will also nd that the weight of the golf bag will affect both speed and steering.
Motocaddy trolleys are designed for the transportation of golf bags and clubs contained within. Using the trolley for any other
purpose may cause damage to the trolley and cause harm to the user. Caution and common sense should always be used.
• Never aim the M7 GPS at other people or golf trolleys;
• When using the M7 GPS in conned spaces (for example car parks) or near water (such as over bridges) it is advisable to use
the ‘Manual’ control mode to ensure that you remain in control;
• Never let the trolley run out of your sight. Always use proper care and control;
• Do not attempt to transport any other equipment;
• The trolley is not designed for the transportation of people;
• The maximum rated load suitable for this trolley is 20kg;
• Do not use the trolley to assist you when walking up hills;
• Submerging the trolley in water (e.g. a lake) is likely to cause damage to the trolley;
• Do not operate the trolley whilst under the influence of drugs or alcohol;
• This trolley can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of
the trolley in a safe way and understand the hazards involved. Children shall not play with the trolley. Cleaning and user
maintenance shall not be made by children without supervision;
Do not attempt to steer the trolley manually when being used in Remote Control mode. Motocaddy cannot take responsibility
for any damage or injury caused from improper use.

Page 7
Trolley Safety / Trolley Care
Safety cut-out
This Motocaddy trolley is tted with safety cut off features. Whilst operating the trolley via the remote control, if no command
is sent to the trolley (any buttons pressed) for longer than 120 seconds, the trolley will stop. Whilst moving, if the trolley travels
out of range of the remote control, the trolley will also cut power to the motors. Whilst operating the trolley in manual mode, if no
adjustment to the speed is made via the dial for longer than 10 minutes, the trolley will stop. If any of these safety features initiate,
pressing the On/Off button or the "+" button of the remote handset will restart the trolley.
Caring for your Trolley
Although your Motocaddy trolley has been weatherproofed, please follow these simple guidelines to help protect your trolley:
• Do not store your trolley outside and minimise exposure to rain as much as possible with an umbrella during heavy rainfall;
• Wipe excess water from the trolley prior to storage;
• Never use a pressure washer to clean your trolley. To prevent water damage, wipe down with a damp cloth;
• Avoid using high pressure air hoses near moving components;
• Avoid exposure to items which may scratch, damage or exert excessive force on the LCD display;
This trolley is designed to require very little maintenance. We do however recommend checking before each use to ensure:
• There is no build up of excess mud and dirt;
• The rear wheels are securely tted and turn freely;
• The front wheels are not clogged up and turn freely;
Only original Motocaddy parts should be used when repairing your trolley.
If you experience an issue with your trolley, please contact our support team for further assistance.

Page 8
Important Battery Safety & Care
Important Battery Safety & Care Information
• Always recharge as soon as possible after nishing your round, regardless of the number of holes played - ideally within
12 hours. Leaving batteries uncharged for extended periods may reduce capacity and could pose a signicant safety risk
which could result in re when the battery is charged. Batteries should always be fully charged prior to storing for long periods;
• Never leave batteries charging for longer than necessary - disconnect once the green LED light indicates the battery is fully charged;
• Ensure that only Motocaddy 28V Lithium batteries are charged with Motocaddy 28V Lithium battery chargers (Model LC-2323)
and the charger is always connected to an earthed socket outlet;
• Batteries must be stored and charged on a dry, non-carpeted surface at a temperature ranging between 10°C and 30°C -
charging outside these temperatures may reduce capacity;
• The battery and charger must only be opened and maintained by authorised personnel. Unauthorised opening increases the
risk of safety issues and will invalidate your warranty;
• Take care not to drop the battery as this may cause damage to the internal cells which could affect battery performance and safety;
• Regularly check the battery for visible signs of damage. Do not charge or use the battery if any damage is suspected - contact our
Technical Support team immediately for advice;
• Use a damp cloth to clean off any dirt, but try to avoid getting the battery too wet (i.e. do not submerge, avoid deep puddles &
do not clean your trolley with the battery in the tray);
• WARNING: For the purposes of recharging the battery, only use the detachable supply unit provided with this trolley;
• If the supply cord is damaged, it must be replaced by Motocaddy, authorised Service Agents or similarly qualied persons to
avoid a hazard;

Page 9
Important Battery Safety & Care
• The battery supplied with this trolley contains battery cells that are non-replaceable;
• Only battery model 28.8V High Power ULTRA 316Wh can be used with this trolley;
• Exhausted batteries are to be removed from the trolley and safely disposed of;
• If the trolley is to be stored unused for a long period, the battery should be removed;
• The battery supply terminals must not to be short-circuited;
IMPORTANT - As with any electrical device, it is not recommended to leave batteries charging overnight or for prolonged
periods without supervision. Motocaddy Lithium batteries can be fully-charged from empty in less than 5 hours, so wait for
the charger light to turn green, switch off at the wall and unplug the battery ready for your next round.
WARNING - If the charger LED light flashes RED and/or GREEN consecutively when connected to the battery, this indicates
there is likely to be a fault with the battery or charger. It is important that you disconnect the charger immediately and contact
our support team for further assistance. Do not attempt to use the battery or charger as this could pose a signicant safety risk
which could result in re.
We are dedicated to protecting the environment and encourage the recycling of Motocaddy products.
Exhausted and damaged batteries should be safely disposed of through a local recycling point (where available).
Alternatively, please contact our support team for further information regarding safe and responsible disposal.

Page 10
Charging your Lithium Battery
Charging your Lithium Battery
The Lithium battery can be left on the trolley or removed for charging. It is possible to charge the battery while the trolley is folded
or unfolded. Always unplug the battery prior to folding the trolley or charging the battery.
1. Plug the Motocaddy 28V Lithium battery charger into an earthed mains power socket
2. The charger light will be GREEN when not attached to a battery to indicate that it is ready to charge
3. Attach the battery cable to the charger matching the black and grey connections
4. The charger light will provide an indication of charging phase:
RED - Battery charging GREEN - Battery fully charged and ready to be disconnected
5. The charging process will take between 3 to 5 hours depending on the depth of discharge.
This may take longer for the rst few charges
6. Once charging is complete, disconnect the charger from the mains power supply and battery
If you connect the battery to the charger and the light goes out, this is likely to indicate that the battery is fully charged.
Please double check the battery on the trolley to ensure that it is fully working.
WARNING - If the charger LED light flashes RED and/or GREEN consecutively when connected to the battery, this indicates
there is likely to be a fault with the battery or charger. It is important that you disconnect the charger immediately and contact
our support team for further assistance. Do not attempt to use the battery or charger as this could pose a signicant safety risk
which could result in re.

Page 11
Battery Hibernation / Battery Management System
Recommendations for hibernation of Lithium Batteries during winter months
If for any reason your Lithium battery is not going to be used for lengthy periods, e.g. 3-months over the winter, the battery should
be stored fully charged. Before the battery is used again, recharge it (top it up) prior to use. The battery must not be left for longer
than 2-months without charging as this could invalidate your warranty.
We recognise that extended absences are not always planned in advance, however when it is likely that you will not be using your
battery for a period of time it is good practice to follow these steps to extend the life of your Lithium battery. Always recharge as
soon as possible after nishing your round, regardless of the number of holes played - ideally within 12 hours. Leaving batteries
uncharged for extended periods may reduce capacity and could pose a signicant safety risk which could result in re when the
battery is charged. Batteries should always be fully charged prior to storing for long periods. Please ensure that the charger is
ALWAYS disconnected from the battery after charging.
Battery Management System (BMS)
Motocaddy Lithium batteries are tted with a comprehensive battery management system (BMS) to protect the battery from
excessive abuse, high currents, deep discharge and overcharge. When the battery is delivered there may be no output as the BMS
is designed to maximize safety whilst shipping. Please ensure that the battery is fully charged prior to connecting it to your trolley
as this will activate the BMS and effectively ‘switch-on’ the battery. From time to time, at deep discharge or long term storage the
BMS may switch-off the battery. A full battery charge will rectify this problem.
Motocaddy golf trolleys are designed to work with the BMS system installed in the Lithium batteries and the battery meter is
also synchronised to work in conjunction with the battery. If for any reason the voltage on the battery falls below the low battery
warning on the trolley, then the BMS may disable the battery to protect it. Again if this occurs please recharge fully. Please be
aware that Lithium batteries tend to ‘drop off’ quickly at the end of the cycle so it is not advisable to attempt to play excessive
holes as the BMS will activate for protection purposes.

Page 12
Attaching the Wheels / Inverting the Wheels
Attaching the Wheels
This trolley does not have a specic left and right wheel. To attach the rear wheels, follow these simple steps:
1. Push and hold the quick release button in towards the centre of the wheel
2. Slide the wheel onto the trolley axle as far as it will go (onto the inner groove)
3. Once in position, release the button and pull the wheel outwards slightly to lock
4. An audible ‘click’ will conrm the wheel is in the correct position
Once correctly attached onto the inner groove, the wheels will not rotate freely in either direction.
The outer groove can be used as a “free-wheel” option if you run out of battery power. Simply slide the wheel onto the outer groove
and pull the wheel outwards slightly to lock. Once connected, the wheel will spin freely without resistance in both directions.
Inverting the Wheels
The rear wheels can be inverted to reduce the trolley width for transportation and storage.
1. Push and hold the quick release button while sliding the wheel off the axle
2. Flip the wheel over, push and hold the button, then slide onto the axle
3. Release the button and pull the wheel out slightly until it engages with the free wheel groove
It is important the wheels are not pushed on too far. They should not touch the chassis.

Page 13
Attaching the Anti-Tip Wheel
Attaching the Anti-Tip Wheel
The Anti-Tip wheel is designed to prevent the trolley from tipping backwards on steeper
inclines and it is recommended that the wheel is ALWAYS tted when navigating using the
remote control handset.
To attach the wheel, simply pull the grey button on the right-hand side out and slide the
wheel attachment into the housing. There will be a ‘click’ when the wheel is securely tted.
To remove the wheel, pull the grey button out and slide the attachment out of the housing.
The Anti-Tip wheel can be removed for cleaning and storage purposes.

Page 14
Setting the trolley to run straight
Adjusting the Front Wheel Alignment
If your trolley is not running in a straight line, there are a couple of adjustments that can be made. The problem can be caused by a
number of factors including a slightly loose bag support or unevenly packed bag. The rst thing to alter is the front wheel alignment:
1. Place the trolley on a flat level surface. Set the rear wheels to "free-wheel" mode (see page 12) and push to check alignment
2. Rotate the front wheels 180˚ to allow access to the quick-release lever (g. 1) and pull down the quick-release lever (g. 2)
3. There are two small metal dials on either side of the housing that are used to realign the wheel (g. 3)
4. If your trolley is veering to the right, you will need to turn the left hand dial clockwise and the right hand dial anti-clockwise
5. If your trolley is veering to the left, you will need to turn the right hand dial clockwise and the left hand dial anti-clockwise
6. Push the quick release lever back up until it rmly clips in to place (g. 4)
7. Rotate the wheel back 180˚ so that it sits underneath the housing (g. 5)
This procedure can be carried out until the trolley is moving in a straight line (you may only need to adjust one dial at a time).
These instructions are based on being in front of the trolley looking at the wheel whilst it is in front of the housing.
Fig 1 Fig 2 Fig 3 Fig 4 Fig 5

Page 15
Setting the trolley to run straight
Motor Trimming
If the trolley is now running straight in remote mode, but not in manual mode then the motors will
need trimming. This will adjust the speed of the selected motor to account for any imbalances.
1. Place the trolley on a flat, level surface and ensure the trolley is stationary (not moving)
2. From the Home screen, select “Settings” and then “Motor Trimming”
3. Read the on-screen instructions and press "Next" when ready (g. 1)
4. Select whether your trolley is pulling to the left or right (g. 2)
5. Select the required adjustment level from 1 (lowest) to 9 (highest) using the "+" and "-" buttons (g. 3)
6. Press "Save" to store settings and exit motor trimming mode
7. Check the trolley is now running in a straight line and repeat steps 1 to 6 if further adjustment is required
It is recommended to start trimming gradually (adjustment 1 to 3) and then increase if necessary.
Motor Trimming will only affect trolley direction under manual (non-remote) control. It is strongly
recommended to adjust the front wheel alignment before continuing with Motor Trimming.
To reset Motor Trimming to factory settings, follow the steps above, but select "0" (increase to "1"
and then back down to "0") and save.
Fig 1 - Motor Trimming
MOTOR TRIMMINGBACK
IF THE TROLLEY IS NOT RUNNING
STRAIGHT IN MANUAL MODE
ADJUST THE FRONT WHEEL
ALIGNMENT BEFORE TRIMMING.
NETCANCEL
LEARN MORE
Fig 2 - Motor Trimming
MOTOR TRIMMINGBACK
IS YOUR TROLLEY PULLING
LEFT OR RIGHT?
WITH THE TROLLEY ON FLAT GROUND, SELECT WHICH
DIRECTION THE TROLLEY IS PULLING WHILE IN MANUAL
MODE
RIGHTLEFT
Fig 3 - Motor Trimming
MOTOR TRIMMINGBACK
4
SELECT ADJUSTMENT LEVEL
SAVE

Page 16
Unfolding your Trolley
Unfolding your Trolley
We recommend unfolding your trolley once the wheels have been un-inverted and re-attached (see page 12).
1. Lift the upper bag support slightly and release the upper latch (g. 1)
2. Unfold the handle and re-secure the latch (g. 2)
3. Release the lower latch (g. 3)
4. Lift the trolley handle up into position (g. 4). The front wheel will automatically unfold
5. Re-secure the lower latch and ensure the auto-open stand is folded away (g. 5)
6. Insert anti-tip wheel (see page 13)
Fig 1 Fig 2 Fig 3 Fig 4 Fig 5

Page 17
Folding your Trolley
Folding your Trolley
1. Release the lower latch (g. 1). The auto-open stand will also be activated
2. Fold the frame forward until fully extended (g. 2). The front wheel will automatically fold underneath
3. Release the upper latch and fold the handle back until the trolley is fully folded (g. 3)
4. Re-secure both latches. If you wish to stand the trolley upright, leave the auto-open stand out. Remember to ensure the
auto-open stand is pushed down if not being used (g. 4)
5. The wheels can be inverted to reduce the trolley width for transportation and storage (g. 5). See page 12 for details
Please ensure the auto-open stand is folded away when not in use to prevent damage. The anti-tip wheel will need to be
removed if you are planning on standing the trolley upright for storage.
Fig 1 Fig 2 Fig 3 Fig 4 Fig 5

Page 18
Lower Bag Supports
Lower Bag Support with EASILOCK™ Bag
All Motocaddy trolleys are tted with the EASILOCK™ bag attachment system. This securely attaches the bag, reduces twisting and
removes the need to use a lower bag strap.
1. If using an EASILOCK™ compatible bag, please ensure that the supplied pins are tted to the bag base (g. 1)
2. If attached, remove the two lower bag support elastic straps by pressing and holding the back of the clip before pulling outwards (g. 2)
3. Align the cut out on the bag base with the lower bag support platform to align the bag pins with the holes on the trolley (g. 3)
4. Lower the bag until the pins locate with the two holes. You should hear a positive “Click” as the bag locks into position
Lower Bag Support with Non-EASILOCK™ Bag
If you are using a non-EASILOCK™ golf bag, please do not remove the two lower bag support elastic straps:
1. Position your bag so it is resting on the lower bag support platform and in the cradle of the upper bag support
2. Stretch the lower bag strap around the bag base and loop the rounded bar underneath the bag support hook (g. 4)
Fig 1 Fig 2 Fig 3 Fig 4

Page 19
Upper Bag Supports / Adjusting the Bag Supports
Upper Bag Supports
The upper bag support straps are secured in the same way as the lower straps using the following steps:
1. Stretch the elasticated strap around the bag & loop the rounded bar underneath the hook (g. 1)
2. Position the two placement straps centrally on your golf bag (g. 2)
Adjusting the Bag Supports
The bag support straps are manufactured from elasticated material to allow your golf bag to be held tightly in position. The strap
should be adjusted to be reasonably tight around the golf bag:
1. Unclip the elasticated straps from the housing by pulling outwards in the direction shown (g. 3)
2. Move the bar as required to tighten or loosen the strap tting. Pulling the bar downwards will tighten, upwards will loosen (g. 4)
3. Ensure that the straps are clipped back into the housing before use (g. 5)
Fig 1 Fig 2 Fig 3 Fig 4 Fig 5

Page 20
Pairing the Remote Control / Handset Lock function
Pairing the Remote Control
In the event that the remote is not responding or you have a new handset, it will need to be paired to the trolley.
1. Press/hold the 'On/Off' button (g. 1a) on the remote handset until a red LED is illuminated (g. 1b)
and release the button once the red LED is no longer visible
2. From the trolley Home screen select “Settings”, “Reset Remote Control” and press "Yes" to clear any
existing handset pairing
3. Navigate back to the trolley Home screen
4. Press/hold the 'On/Off' button on the remote handset until a green LED is illuminated. Release the
button and wait until the green LED stops flashing. This indicates that pairing has been successful
If the green LED continues to flash, pairing has not been successful. Restart the pairing process.
Handset Lock function
The remote handset can be locked by pressing the Lock button (g. 2a), when this is pressed the LED
will either flash green or red (g. 2b). Green indicates that the handset is unlocked and red indicates locked.
When it is locked the directional buttons will be disabled and a red LED will flash when they are pressed,
the Stop button will still operate and show a green LED when pressed.
If the handset is locked whilst the trolley is running in remote mode, the trolley will stop after 4 seconds as
the handset will stop sending a signal. If the trolley is in Manual mode it will continue to run but can still
be stopped using the Stop button on the handset.
Pressing the Lock button again (g. 2a) so the LED flashes green (g. 2b), will unlock the handset and all
buttons will be enabled.
Fig 1
Fig 2
A
B
A
B