Moxa Technologies MGate 5101-PBM-MN User manual

P/N: 1802051010013
*1802051010013*
MGate 5101-PBM-MN
Quick Installation Guide
Version 3.1, November 2019
Technical Support Contact Information
www.moxa.com/support
Moxa Americas:
Toll
-free: 1-888-669-2872
Tel:
1-714-528-6777
Fax:
1-714-528-6778
Moxa China (Shanghai office):
Toll
-free: 800-820-5036
Tel:
[phone]
Fax:
[phone]
Moxa Europe:
Tel:
[phone]
Fax:
[phone]
Moxa Asia-Pacific:
Tel:
[phone]
Fax:
[phone]
Moxa India:
Tel:
[phone]
Fax:
[phone]

2019 Moxa Inc. All rights reserved.

- 2 -
Overview
The MGate 5101-PBM-MN is an industrial Ethernet gateway for
PROFIBUS-to-Modbus-TCP network communication.
Package Checklist
Before installing the MGate 5101-PBM-MN, verify that the package
contains the following items:
•1 MGate 5101-PBM-MN gateway
•Quick installation guide (printed)
•Warranty Card
Please notify your sales representative if any of the above items are
missing or damaged.
Optional Accessories (can be purchased separately):
•CBL-F9M9-150: DB9-female-to-DB9-male serial cable, 150 cm
•CBL-F9M9-20: DB9-female-to-DB9-male serial cable, 20 cm
•Mini DB9F-to-TB: DB9-female-to-terminal-block connector
•WK-36-01: Wall-mounting kit
Hardware Introduction
LED Indicators
LED
Color
Function
PWR1
Green
Power is on
Off
Power is off
PWR2
Green
Power is on
Off
Power is off
Ready
Green
Steady on: Power is on and the MGate is
functioning normally
Blinking: The MGate has been located by the
MGate Manager’s Location function
Red
Steady on: Power is on and the MGate is booting
up
Blinking: Indicates an IP conflict, or the DHCP or
BOOTP server is not responding properly
Off
Power is off or fault condition exists
COMM
Off
No data exchange
Green
Data exchange with all slaves
Green,
flashing
Data exchange with at least one slave (not all
configured slaves can communicate with gateway)
Red
Bus control error
CFG
Off
No PROFIBUS configuration
Green
PROFIBUS configuration OK
PBM
Off
PROFIBUS master is offline
Red
PROFIBUS master is in STOP mode
Green,
flashing
PROFIBUS master is in CLEAR mode
Green
PROFIBUS master is in OPERATE mode
TOK
Green
Gateway holds the PROFIBUS token
Off
Gateway is waiting for the PROFIBUS token

- 3 -
LED
Color
Function
Ethernet
Amber
Steady: 10Mbps, no data is transmitting
Blinking: 10Mbps, data is transmitting
Green
Steady: 100Mbps, no data is transmitting
Blinking: 100Mbps, data is transmitting
Off
Ethernet cable is disconnected
Reset Button
The reset button is used to load factory defaults. Use a pointed object
such as a straightened paper clip to hold the reset button down for five
seconds. Release the reset button when the Ready LED stops blinking.
Hardware Installation Procedure
STEP 1:
Connect the power adapter. Connect the 12-48 VDC power line
or DIN
-rail power supply with the MGate 5101-PBM-MN
device’s terminal block.
Make sure the adapter is connected to
an earthed socket.
STEP 2:
Use a PROFIBUS cable to connect the unit to a PROFIBUS slave
device.
STEP 3:
Connect the unit to the Modbus TCP device.
STEP 4
:
The
MGate 5101-PBM-MN series is designed to be
attached to
a DIN
rail or mounted on a wall. For DIN-rail
mounting, push
down the spring and properly attach it to the
DIN-rail until
it
“snaps” into place. For wall
mounting, install the wall-mount
kit (optional) first
and then screw the device onto the wall.
Wall or Cabinet Mounting
Two metal plates are provided for mounting the
unit on a wall or inside a cabinet. Attach the plates
to the unit’s rear panel with screws. With the plates
attached, use screws to mount the unit on a wall.
The heads of the screws should be 5 to 7 mm in
diameter, the shafts should be 3 to 4 mm in
diameter, and the length of the screws should be
more than 10.5 mm.
For each screw, the head should be 6 mm or less in diameter, and the
shaft should be 3.5 mm or less in diameter.

- 4 -
The following figure illustrates the two mounting options:
Software Installation Information
To install MGate Manager, please download it from Moxa’s website at
http://www.moxa.com. For more detailed information about MGate
Manager, click the Documents button and select the MGate 5101-PBM-MN
User’s Manual.
The MGate 5101 also supports login via a web browser.
Default IP address: 192.168.127.254
Default account: admin
Default password: moxa
Pin Assignments
PROFIBUS Serial Port (Female DB9)
PIN
Signal Name
1
–
2
–
3
PROFIBUS D+
4
RTS
5
Signal common
6
5V
7
–
8
PROFIBUS D-
9
–

- 5 -
Power Input and Relay Output Pinouts
V2+ V2-
V1+ V1-
Shielded
Ground
DC
Power
Input 2
DC
Power
Input 2
N.O. Common N.C.
DC
Power
Input 1
DC
Power
Input 1
Specifications
Power Input
12 to 48 VDC
Power Consumption
(Input Rating)
12 to 48 VDC, 360 mA (max.)
Operating Temperature
Standard Models: 0 to 60°C (32 to 140°F)
Wide Temp. Models: -40 to 75°C (-40 to
167°F)
Storage Temperature
-40 to 85°C (-40 to 185°F)
ATEX and IECEx Information
1. ATE X Certificate number: DEMKO 14 ATEX 1288
2. IECEx number: IECEx UL 14.0023X
3. Certificate string: Ex nA IIC T4 Gc
Ambient range: 0°C ≤Tamb ≤60°C (for suffix without –T)
Ambient range: -40°C ≤Tamb ≤75°C (for suffix without –T)
4. Standards covered:
EN 60079-0: 2012+A11:2013/IEC 60079-0: Ed 6.0
EN 60079-15:2010/IEC 60079-15: Ed 4.0
5. Field-wiring connection:
The device uses a terminal block, solder on the power distribution
board, suitable for 12-24 AWG wire size, torque value 4.5 lb-in (0.51
N-m).
6. Battery information: Battery is not user replaceable.
7. Installation instructions:
•A 4 mm2conductor must be used when the connection to the
external grounding screw is utilized.
•Conductors suitable for use at an ambient temperature of 84°C
must be used for the power supply terminal.
8. Special conditions for safe use:
•The device is to be installed in an IECEx/ATEX Certified IP54
enclosure and accessible only through the use of a tool.
•The device is for use in an area of not more than pollution degree
2 in accordance with IEC 60664-1.

- 6 -
ATTENTION
For installations in hazardous locations (Class 1, Division 2):
These devices are to be installed in an enclosure with a
tool-removable cover or door, suitable for the environment.
NOTE
The equipment
must be suitable for use in Class 1, Division 2,
Groups A, B, C, D, or nonhazardous locations only.
WARNING
EXPLOSION HAZARD
Do not disconnect equipment unless the power has been switched
off, or the area is known to be nonhazardous.
WARNING
EXPLOSION HAZARD
Substitution of any components may impair suitability for Class 1,
Division 2.
WARNING
EXPOSURE TO SOME CHEMICALS MAY
DEGRADE THE SEALING
PROPERTIES OF MATERIALS USED IN THE FOLLOWING DEVICE:
Sealed Relay Device U21.
Moxa Inc.
Fl. 4, No. 135, Lane 235, Baoqiao Rd.
Xindian Dist., New Taipei City, 23145, Taiwan, R.O.C.