Moxa Technologies MGate 5102-PBM-PN User manual

– 1 – – 2 – – 3 –
P/N: 1802051020010
MGate 5102-PBM-PN
Quick Installation Guide
First Edition, January 2013
Overview
The MGate 5102-PBM-PN is an industrial Ethernet gateway for
PROFIBUS and PROFINET network communication.
Package Checklist
Before installing the MGate 5102-PBM-PN, verify that the package
contains the following items:
•1 MGate 5102-PBM-PN gateway
•RJ45 to DB9 cable (for console use)
•Documentation and software CD
•Quick installation guide
•Warranty card
Optional Accessories:
•DR-45-24: 45W/2A DIN rail 24 VDC power supply with
universal 85 to 264 VAC input
•DR-75-24: 75W/3.2A DIN rail 24 VDC power supply with
universal 85 to 264 VAC input
•DR-120-24: 120W/5A DIN rail 24 VDC power supply with 88 to
132 VAC/176 to 264 VAC input by switch
•WK-36-01: Wall mounting kit
Please notify your sales representative if any of the above items
are missing or damaged.
Hardware Introduction
LED Indicators
LED
Color
Function
PWR1
Green
Power is on
Off
Power is off
PWR2
Green
Power is on
Off
Power is off
Ready
Green
Steady on: Power is on and the MGate is
functioning normally
Blinking: The MGate has been located by the
MGate Manager’s Location function
Red
Steady on: Power is on and the MGate is
booting up
Blinking: Indicates an IP conflict, or DHCP or
BOOTP server is not responding properly
Fast blinking: microSD card failed
Off
Power is off or fault condition exists
COMM
Green
Steady on: No data exchange
Blinking: Data exchange with at least one
slave
Red
Data exchange with all slaves
Off
Bus control error
CFG
Green
PROFIBUS configuration OK
Off
No PROFIBUS configuration
TOK
Green
Gateway holds the PROFIBUS token
Off
Gateway is waiting for the PROFIBUS token
PBM
Green
Steady on: PROFIBUS master is in OPERATE
mode
Blinking: PROFIBUS master is in CLEAR
mode
Red
PROFIBUS master is in STOP mode
Off
PROFIBUS master is offline
PN Green
Steady on: PROFINET I/O is connected and
controller is in RUN mode
Blinking: PROFINET I/O is connected but
controller is in STOP mode
Off
No connection with IO Controller
Ethernet
Amber
Steady: 10 Mbps, no data is transmitting
Blinking: 10 Mbps, data is transmitting
Green
Steady: 100 Mbps, no data is transmitting
Blinking: 100 Mbps, data is transmitting
Off
Ethernet cable is disconnected
Dimensions
Reset Button
The reset button is used to load factory defaults. Use a pointed
object such as a straightened paper clip to hold the reset button in
for five seconds. Release the reset button when the Ready LED
stops blinking.

– 4 – – 5 – – 6 –
www.moxa.com/support
The Americas:
[phone] (toll-free: 1-888-669-2872)
Europe:
[phone]
Asia-Pacific:
[phone]
China:
[phone] (toll-free: 800-820-5036)
2013 Moxa Inc. All rights reserved.
Hardware Installation Procedure
1. Connect the power adaptor. Connect the 12-48 VDC power line
or DIN rail power supply to the MGate 5102-PBM-PN device’s
terminal block.
2. Use a PROFIBUS cable to connect the unit to a PROFIBUS slave
device.
3. Connect the unit to the PROFINET I/O controller.
4. The MGate 5102-PBM-PN is designed to be attached to a
DIN rail or mounted on a wall. For DIN rail mounting, push
down the spring and properly attach it to the DIN rail until it
“snaps” into place. For wall mounting, install the wall mount kit
(optional) first, and then screw the device onto the wall. The
following figure illustrates the two mounting options:
Software Installation Information
To install MGate Manager, insert the MGate Documentation and
Software CD into your PC’s CD-ROM drive, and then run the
following setup program to begin the installation process from the
“Software” directory:
MGM_Setup_[Version]_Build_[DateTime].exe
The filename of the latest version may have the following format:
MGM_Setup_Verx.x.x_Build_xxxxxxxx.exe.
For detailed information about MGate Manager, refer to the MGate
5102-PBM-PN User's Manual, which can be found in the “Document”
directory.
Pin Assignments
PROFIBUS Serial Port (female DB9)
PIN
Signal Name
1
N.C.
2
N.C.
3
PROFIBUS D+
4
RTS
5
Signal common
6
5V
7
N.C.
8
PROFIBUS D-
9
N.C.
Power Input and Relay Output Pinouts
V2+ V2- V1+ V1-
Shielded
Ground
DC
Power
Input 2
DC
Power
Input 2
N.O.
Common
N.C.
DC
Power
Input 1
DC
Power
Input 1
Specifications
Power Requirements
Power Input
12 to 48 VDC
Power Consumption
430 mA @ 12 VDC, 120 mA @ 48 VDC
Operating Temperature
Standard models: 0 to 60°C (32 to
140°F)
Wide temp. models: -40 to 75°C (-
40
to 167°F) for –T model
Ambient Relative Humidity
5 to 95% RH
Dimensions
36 x 105 x 140 mm (1.42 x 4.13 x 5.51
in)
Reliability
Alert Tools
Built-in buzzer and RTC
MTBF
980,417 hrs